Infinix HOT 50 Pro User Manual
Model: X6881
Know Your Phone
This section identifies the main components of your Infinix HOT 50 Pro.
External Features:
- Front View: The front of the phone features a display. At the top center of the display is the front camera.
- Back View: The back of the phone houses a camera module in the top left area. An NFC indicator is also present on the back.
- Side View: The sides of the phone feature the volume + button, volume - button, and the power button.
SIM/SD Card Installation
Follow these steps to install your SIM and/or SD cards:
- Power off your phone.
- Refer to the illustration for SIM/SD card installation. The SIM tray typically accommodates two SIM cards or one SIM card and one SD card. Ensure correct orientation when inserting the tray back into the phone.
Charging the Phone
You can charge your phone using the provided charger and USB cable, or by connecting it to a computer via USB. It is recommended to use only Infinix-approved chargers and cables to prevent damage and warranty invalidation.
Illustration Description: The phone is shown with a USB cable connected to its charging port.
FCC Caution
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference.
- This device must accept any interference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
Information to the User
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Specific Absorption Rate (SAR) Information
This mobile phone meets the government's requirements for exposure to radio waves. The guidelines are based on standards developed by independent scientific organizations through periodic and thorough evaluation of scientific studies. The standards include a substantial safety margin designed to assure the safety of all persons regardless of age or health.
FCC RF Exposure Information and Statement: The SAR limit of USA (FCC) is 1.6 W/kg averaged over one gram of tissue. Device types: X6881 (FCC ID: 2AIZN-X6881) has also been tested against this SAR limit. The highest SAR value reported under this standard during product certification for use at the ear is 1.099 W/kg and when properly worn on the body is 0.746W/kg.
Body-worn Operation
This device was tested for typical body-worn operations. To comply with RF exposure requirements, a minimum separation distance of 1.0cm must be maintained between the user's body and the handset, including the antenna. Third-party belt-clips, holsters, and similar accessories used by this device should not contain any metallic components. Body-worn accessories that do not meet these requirements may not comply with RF exposure requirements and should be avoided. Use only the supplied or an approved antenna.
DTS Information
For DTS patents, see http://patents.dts.com. Manufactured under license from DTS Licensing Limited. DTS, the Symbol, & DTS and the Symbol together are registered trademarks or trademarks of DTS, Inc. in the United States and/or other countries. © DTS, Inc. All Rights Reserved.
Operating System
Operating System: Android™
Android is a trademark of Google LLC.
Exploded Diagram Specification
The following table lists the components identified in the exploded diagram:
| Part Number | Component Name | Part Number | Component Name |
|---|---|---|---|
| 1 | TP+LCM | 2 | FRONT COVER |
| 3 | MB CU FOIL A | 4 | RECEIVER |
| 5 | FRONT CAMERA | 6 | REAR CAMERA BTB FOAM |
| 7 | SIM CARD | 8 | MAIN BOARD |
| 9 | 2W REAR CAMERA ADHESIVE | 10 | MB CU FOIL B |
| 11 | 2W REAR CAMERA | 12 | 50M REAR CAMERA |
| 13 | SIDE KEY FPC | 14 | 2M REAR CAMERA RUBBER |
| 15 | FLASH FPC | 16 | LIGHT FPC |
| 17 | FRONT CAMERA CU FOIL | 18 | PS RUBBER |
| 19 | MAIN BOARD GRAPHITE | 20 | MIDDLE COVER |
| 21 | SCREW M1.4*L3.5 | 22 | BATTERY COVER |
| 23 | DECO FRAME | 24 | DECO PLATE |
| 25 | GLASS LENS MAIN | 26 | GLASS LENS AUX |
| 27 | COMPOSITE LENS | 28 | SCREW M1.4*L2.5 |
| 29 | AUDIO JACK RUBBER | 30 | USB RUBBER |
| 31 | MOTOR | 32 | SMALL BOARD |
| 33 | SPEAKER | 34 | FINGER FOAM |
| 35 | FINGER MODULE | 36 | COAXIAL CABLE |
| 37 | BATTERY | 38 | MAIN FPC |
| 39 | REAR CAMERA CU FOIL |
