Infinix ZERO Flip X6962 User Manual
Exploded Diagram Specification
An exploded view diagram illustrating the internal components of the Infinix ZERO Flip X6962. Each part is numbered and corresponds to a detailed list below.
Component List
| Part Number | Description | Part Number | Description |
|---|---|---|---|
| 1 | RCAM DECO STEEL | 2 | GLASS CAMERA LENS |
| 3 | CNC WIDGET CAM DECO1 | 4 | GLASS CAMERA LENS |
| 5 | CNC WIDGET CAM DECO2 | 6 | COB MODULE AF 32M |
| 7 | COB MODULE OIS 50M | 8 | ONCELL 3.64 1056*1066 |
| 9 | UP CONN STEEL 1 | 10 | UP CONN STEEL ASM2 |
| 11 | VLCM BTBSTEEL | 12 | VICE LCM CON FOAM 2 |
| 13 | FLASH LENS AE11 2 | 14 | POLYMER BATTERY BL |
| 15 | VICE LCM CON FOAM 1 | 16 | UP BAT COVER FOAM |
| 17 | VICE LCM CON FB | 18 | GLASS BACK COVER ASSEMBLY |
| 19 | THERMAL RADIATION FILM DOWNFRAME | 20 | THERMAL RADIATION FILM DOWN SPK |
| 21 | BOX SPEAKER | 22 | SUB PCB FRAME ASM |
| 23 | RUBBER USB SEAL | 24 | FPCA RF |
| 25 | MOTOR LINEAR | 26 | FPCA MAIN 4L |
| 27 | HOMEMADE ANT SUB | 28 | FERRITE ANTENNA NFC |
| 29 | SUB BTB MYLAR | 30 | ANT FPC SUPPORT FOAM |
| 31 | CNC CARD HOLDER | 32 | HOMEMADE PCBA SUB |
| 33 | DOWN BAT FOAM A | 34 | BAT MYLAR |
| 35 | MAIN FPC FIXED MYLAR | 36 | VICE LCM FOAM |
| 37 | ANT FPC FRAME | 38 | POLYMER BATTERY BL |
| 39 | DOWN MI HSG LCM | 40 | CNC MIDDLE HOUSING |
| 41 | THERMAL RADIATION FILM | 42 | ONCELL 6.9 FHD |
| 43 | DOWN MI HSG MYLAR | 44 | DOWN MAIN FPC FRAME |
| 45 | MAIN LCM DECO DOWN | 46 | MIM WIDGET HINGE FIXED |
| 47 | FOLD AXLE | 48 | FP FPC SEAL FOAM |
| 49 | FP SUPPORT FOAM | 50 | MAIN LCM DECO UP |
| 51 | THERMAL RADIATION FILM UP MI HSG | 52 | UP MAIN FPC FRAME ASM |
| 53 | FP FRAME | 54 | SIDE KEY FPC FOAM |
| 55 | SIDE KEY FPC FOAM | 56 | SIDEKEYFPC SEAL FOAM |
| 57 | FPCA SIDEKEY | 58 | KEY FRAME |
| 59 | UP MI HSG LCMADS | 60 | CNC WIDGET VOL KEY |
| 61 | LT&F FLASH FPC FRAME | 62 | FPCA FRONT FLASH 2L |
| 63 | FLASH LENS AE11 | 64 | CNC MIDDLE HOUSING |
| 65 | VICE LCM FOAM ADS | 66 | HOMEMADE PCBA MB |
| 67 | F CAM DUST MYLAR | 68 | F CAM FIXED FRAME |
| 69 | F CAM SEAL ADS | 70 | WIDE ANGLE CAM FOAM |
| 71 | RUBBER R LT SENSOR SEAL | 72 | THERMAL RADIATION FILM SHIELD |
| 73 | COAXIAL CABLE | 74 | W ANGLE CAMFOIL |
| 75 | THERMAL RADIATION FILM UP FRAME | 76 | DOWN BAT FOAM A |
| 77 | SQUARE RECEIVER | 78 | COB MODULE AF 32M |
| 79 | MAIN FPC FIXED MYLAR | 80 | MAIN SHIELD MYLAR |
| 81 | M CAM COP FOIL | 82 | UPPER FRAME ASSEMBLY |
| 83 | CAPACITIVE FINGERPRINT | 84 | LCM FPC CONN ADS |
| 85 | NDFEB MAGNET5 IMP FOAM | 86 | NDFEB MAGNE 5 |
| 87 | SIDE KEY MYLAR | 88 | CAM SEAL FOAM |
| 89 | MB SHIELD FOIL1 | 90 | MB SHIELD COP FOIL2 1 |
| 91 | F LT SENSOR MYLAR | A | MC SCREW M1.4*L3.5*D2.5*H0.5 |
| B | SCREW MAC M1.4*L4.0*D2.3*H0.5 | C | DUALSCREW M1.4*L2.35*D2.45*H0.75 |
| D | MC SCREW M1.2*L1.7*D2.0*H0.3 | E | MC SCREW M1.4*L2*D2.5*H0.5 |
Know Your Phone
Diagrams showing the front and side views of the Infinix ZERO Flip. Key components are indicated by numbers:
- 1. Front camera
- 2. Volume + button
- 3. Volume - button
- 4. Power button & side fingerprint sensor
- 5. NFC area
SIM Card Installation
Instructions
- Power off your phone.
- Refer to the following picture for SIM card installation.
A diagram illustrating the SIM card tray location on the Infinix ZERO Flip.
Charging the Phone
You can charge your phone with a charger or by connecting it to a computer using a USB cable (comes with the phone).
Use only Infinix chargers and cables. Other chargers or cables may damage the phone and invalidate its warranty.
Diagrams showing the Infinix ZERO Flip connected to a USB cable for charging, with a close-up view of the USB-C port.
FCC Caution
Labelling Requirements
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received, including interference that may cause undesired operation.
Information to User
Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the device.
Information to the User (Class B Digital Device)
Note: This device has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This device generates, uses, and may radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this device does cause harmful interference to radio or television reception (able to be determined by turning the device off and on), the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the device and receiver.
- Connect the device to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Specific Absorption Rate (SAR) Information
This mobile phone meets the government's requirements for exposure to radio waves. The guidelines are based on standards developed by independent scientific organizations through periodic and thorough evaluation of scientific studies. The standards include a substantial safety margin designed to assure the safety of all persons regardless of age or health.
FCC RF Exposure Information and Statement: The SAR limit of USA (FCC) is 1.6 W/kg averaged over one gram of tissue. Device types: X6962 (FCC ID: 2AIZN-X6962) has also been tested against this SAR limit. The highest SAR value reported under this standard during product certification for use at the ear is 0.78 W/kg and when properly worn on the body is 0.73 W/kg.
Body-worn Operation
This device was tested for typical body-worn operations. To comply with RF exposure requirements, a minimum separation distance of 1.0 cm must be maintained between the user's body and the handset, including the antenna. Third-party belt-clips, holsters, and similar accessories used by this device should not contain any metallic components. Body-worn accessories that do not meet these requirements may not comply with RF exposure requirements and should be avoided. Use only the supplied or an approved antenna.
Legal Information
For DTS patents, see http://patents.dts.com. Manufactured under license from DTS Licensing Limited. DTS, the Symbol, & DTS and the Symbol together are registered trademarks or trademarks of DTS, Inc. in the United States and/or other countries. © DTS, Inc. All Rights Reserved.
Operating System: Android™
Android is a trademark of Google LLC.
