Infinix HOT 50 Pro+
User Manual (Model X6880)
Exploded Diagram Specification
A visual representation of the Infinix HOT 50 Pro+ components, detailing their arrangement and part numbers for assembly or repair.
| Part Number | Component Name |
|---|---|
| 1 | OLED |
| 2 | LCM HEAT FILM |
| 3 | MIDDLE FRAME COMPONENT |
| 4 | 13M CAMERA |
| 5 | 50M CAMERA |
| 6 | 2M CAMERA |
| 7 | FPCA POST-LIGHT PERCEPTION |
| 8 | MAIN BOARD |
| 9 | RECEIVER |
| 10 | COAXIAL CABLE |
| 11 | FORESIGHT GROUNDING COPPER FOIL |
| 12 | SIDEKEY FPC |
| 13 | MATHERBOARD HEAT FILM |
| 14 | BL-49UX_4900mAh_CB_ATL |
| 15 | RE_M_CAM GROUNDING COPPER FOIL |
| 16 | PROACTIVE DUSTPROOF MYLAR |
| 17 | UPPER BRACKET |
| 18 | 2M CAMERA RUBBER |
| 19 | CAMERA TRIM |
| 20 | SCREW M1.4 L3.0 |
| 21 | RE-CAM COMPOSITE PANEL TRIM |
| 22 | BATTERY COVER |
| 23 | RE-MAIN CAMERA LENSE |
| 24 | RE-SECONDARY CAMERA LENSE |
| 25 | LIGHT-SENSITIVE LENSE |
| 26 | LOW-SPEAKER HEAT |
| 27 | LOWER BRACKET |
| 28 | SCREEN FPC BTB SILICONE SHEET |
| 29 | SMALL PLATE BTB SILICONE SHEET |
| 30 | SMALL PLATE PRESSING FOAM |
| 31 | STEEL INJECTION MOLDED TRAY |
| 32 | SCREEN FPC GROUNDING CON-FOAM |
| 33 | LOWER HORN |
| 34 | SCREEN FPC SEALANT SLEEVE |
| 35 | MOTOR |
| 36 | FINGERPRINT MODULE |
| 37 | TYPE C USB RUBBER |
| 38 | SUB BOARD |
Know Your Phone
Diagrams showing the front and rear views of the Infinix HOT 50 Pro+.
- 1. Front camera
- 2. Volume + button
- 3. Volume - button
- 4. Power button
- 5. NFC (Near Field Communication)
SIM/SD Card Installation
Steps:
- Power off your phone.
- Refer to the following diagrams for SIM/SD card installation.
Illustrations showing the placement of SIM and SD cards into their respective trays.
Charging the Phone
Procedure:
- Charge your phone using a charger or by connecting it to a computer via a USB cable (included with the phone).
- Use only Infinix chargers and cables. Using other chargers or cables may damage the phone and void its warranty.
Diagram illustrating the phone being charged via a USB cable.
FCC Caution
Compliance Statement:
- This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- (1) This device may not cause harmful interference.
- (2) This device must accept any interference received, including interference that may cause undesired operation.
- Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the device.
Information to the User:
- This device has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
- This device generates, uses, and may radiate radio frequency energy. If not installed and used in accordance with the instructions, it may cause harmful interference to radio communications.
- There is no guarantee that interference will not occur in a particular installation.
- If this device causes harmful interference to radio or television reception (which can be determined by turning the device off and on), the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the device and receiver.
- Connect the device to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Specific Absorption Rate (SAR) Information
General Statement:
- This mobile phone meets government requirements for exposure to radio waves. Guidelines are based on standards developed by independent scientific organizations through periodic and thorough evaluation of scientific studies.
- The standards include a substantial safety margin to assure the safety of all persons, regardless of age or health.
FCC RF Exposure Information and Statement:
- The SAR limit for the USA (FCC) is 1.60 W/kg averaged over one gram of tissue.
- Device types: X6880 (FCC ID: 2AIZN-YYS-X6880) has been tested against this SAR limit.
- The highest SAR value reported under this standard during product certification for use at the ear is 0.84 W/kg, and when properly worn on the body is 0.76 W/kg.
Body-worn Operation:
- This device was tested for typical body-worn operations. To comply with RF exposure requirements, a minimum separation distance of 1.0 cm must be maintained between the user's body and the handset, including the antenna.
- Third-party belt-clips, holsters, and similar accessories used with this device should not contain any metallic components.
- Body-worn accessories that do not meet these requirements may not comply with RF exposure requirements and should be avoided.
- Use only the supplied or an approved antenna.
Legal and System Information
DTS Patents:
- For DTS patents, see http://patents.dts.com.
- Manufactured under license from DTS Licensing Limited.
- DTS, the DTS Symbol, and DTS and the Symbol together are registered trademarks or trademarks of DTS, Inc. in the United States and/or other countries.
- © DTS, Inc. All Rights Reserved.
Operating System:
- Operating System: Android™
- Android is a trademark of Google LLC.
