Reedog Patpet T800 Pro Wireless Fence System
User Manual
Introduction
Read this user manual carefully and keep it in a safe place.
This manual provides instructions for the Reedog Patpet T800 Pro wireless fence system, including its components, setup, operation, and safety precautions.
Package Contents
- Transmitter
- Collar with receiver
- USB-C charging cable
- Short contact points
- Long contact points
- Test light
- Wrist strap
- User manual
Product Description
Transmitter
- TFT Display
- Wrist strap loop
- Lock button
- Up/Down buttons
- Settings button
- Impulse button
- Sound button
- Vibration button
- Dog 1/2/3 button
- Charging port
Transmitter Display Modes
- Fence Mode: Displays fence status and level.
- Training Mode: Shows training parameters like sound, vibration, and impulse levels.
- Bark Collars Mode: Displays sensitivity settings for anti-bark functionality.
Collar Components
- Collar strap
- LED indicator
- On/Off button
- Buckle
- Charging port with cover
- Contact points
LED Signalization (Receiver)
- Slowly flashing white LED: Receiver is charging.
- Solid white light: Receiver is fully charged.
- Flashing once every 5 seconds: Receiver is functioning normally.
- Flashing white LED: Sound, vibration, or impulse mode is active.
First Use
Before first use, fully charge the transmitter and receiver using the provided USB-C cable.
- Transmitter Charging: The battery icon indicates charging progress. It turns solid when fully charged.
- Receiver Charging: The white LED indicator will flash slowly while charging and turn solid when fully charged.
Product Power On/Off
- Transmitter: Press the Lock button briefly to turn on. Press and hold the Lock button to turn off.
- Receiver: Press the On/Off button briefly to turn on (one beep, one vibration). Press and hold the On/Off button to turn off (two beeps, two vibrations).
Test Mode
Press the On/Off button to enter test mode (display shows '0'). Mimic a dog's bark into the microphone sensor on the back of the receiver.
Switching Between Functions
Press and hold the Settings button to enter function switching mode. Briefly press the Settings button to select between Training Collar, Anti-Bark Collar, and Fence modes.
Pairing Transmitter with Receiver
For training and fence functions, the transmitter and receiver must be paired. One transmitter can be paired with up to 3 receivers.
- Turn on the transmitter and switch to Training mode.
- Press and hold the Dog 1/2/3 button on the transmitter to enter channel switching mode. Briefly press the button to switch channels.
- Turn off the receiver. Press and hold the On/Off button for 3-5 seconds until the receiver vibrates and enters pairing mode. The LED indicator will flash for 15 seconds.
- Within 15 seconds, press the Sound/Vibration button on the transmitter.
Successful pairing is confirmed by a beep. The transmitter will display the receiver's battery level after successful pairing. If the time limit is exceeded, repeat the steps.
How to Use the Fence
The fence function is disabled by default.
Turning Fence On/Off
After selecting the fence function, choose the desired dog channel and briefly press the Lock button to enable or disable the function.
Note: This function consumes more energy. Turn it off when not in use. Adjust the fence radius level using the Up/Down buttons (levels 1-8).
Note: Each dog may require a different setting. Select the appropriate dog channel before adjusting the level.
| Fence Level | Distance (meters) |
|---|---|
| Level 1 | 10 |
| Level 2 | 20 |
| Level 3 | 30 |
| Level 4 | 50 |
| Level 5 | 70 |
| Level 6 | 90 |
| Level 7 | 110 |
| Level 8 | 200 |
The above data indicates the maximum effective distance in an open environment. Obstacles or signal interference may reduce the range in real-world use. Test the device in your own environment as actual performance may vary.
Setting Alerts
The default setting is vibration. Briefly press the Vibration or Impulse button to switch modes. When the dog crosses the boundary, the collar will issue a warning and automatically increase the intensity from level 1 to 6. The transmitter will emit an audible reminder, and the corresponding dog's fence icon will flash slowly.
Note: You can also briefly press the Sound button to prevent the collar from emitting a sound when the dog leaves the allowed radius. The transmitter will still issue a warning, and the owner must manually trigger a warning to call the dog back.
How to Use the Training Function
Setting Levels
After entering the training function, select the desired dog channel. Briefly press the Settings button to cycle through sound, vibration, and impulse modes. Use the Up/Down buttons to adjust the levels for sound, vibration, and impulse.
- Sound Warning: Short or long press of the Sound button emits a sound warning (8 levels, varying tones).
- Vibration Warning: Short or long press of the Vibration button emits a vibration warning (8 levels, higher levels indicate stronger vibration).
- Impulse Warning: Short or long press of the Impulse button emits an impulse warning (16 levels, higher levels indicate stronger impulse).
- Impulse Lock/Unlock: Briefly press the Lock button to lock/unlock impulse mode.
How to Use the Anti-Bark Collar
The collar is set to automatic warning by default.
Turning Anti-Bark Collar On/Off
After activating the anti-bark function, select the desired dog channel and briefly press the Lock button to activate or deactivate the function.
Selecting Warning Mode
Ensure the anti-bark mode is active. Briefly press the vibration or static electricity button to select vibration or impulse mode. Tip: Upon activation of a warning mode, the level automatically increases from 1 to 6, with higher levels providing stronger warnings.
Setting Sensitivity Level
Use the Up/Down buttons to adjust the sensitivity level from 1 to 5. Higher levels are more prone to triggering.
Real-Time Tracking
This function is effective up to approximately 180 meters from the transmitter. Information will not be displayed beyond this distance.
Icons represent different dog activities: standing, walking, running, jumping.
How to Install Contact Points
- Attach the contact points.
- Use the test light to tighten the contact points.
How to Use the Test Light
Ensure the contact points are correctly installed and the device is paired.
Turn on the training function and unlock the impulse mode. Place the test light on the contact points and press the impulse button. If the test light illuminates, the impulse (static stimulation) is functioning correctly.
How to Assemble the Collar
- Thread the strap through the receiver.
- Thread the strap through the buckle.
- Thread the excess strap through the silicone ring.
How to Fit the Collar on the Dog
Ensure the product fits snugly but is loose enough for one finger to fit between the collar and the dog's neck. Place the receiver in the middle of the neck, with the power button facing upwards and the contact points aligned with the neck.
Note: If your dog has long fur, it may be necessary to trim the fur around the metal contact points and use the longer metal contact points. The excess strap can be trimmed.
Safety Precautions for Wearing the Collar
- Avoid prolonged or tight wearing of the collar to prevent skin irritation.
- Ensure your dog does not wear the collar for more than 12 hours a day.
- Adjust the collar's position on your pet's neck every 1-2 hours.
- Regularly check the collar's tightness to prevent excessive pressure.
- Do not attach a leash to the collar to avoid unnecessary pressure on the device.
- Clean the area around your pet's neck and the receiver's contact area with a damp cloth weekly.
- Check the contact area daily for any signs of rash or discomfort.
- If a rash or discomfort occurs, discontinue use until the skin heals. If symptoms persist for more than 48 hours, seek veterinary assistance immediately.
Compliance and Service
The device has been approved for use in EU countries and bears the CE mark. All necessary documentation is available on the website: www.elektro-obojky.cz
Technical parameters, features, and printing errors are subject to change.
Service Center and Distribution
Reedog, s.r.o.
Sedmidomky 459/8
101 00 Praha 10
Tel: +420 216 216 106
Email: info@elektro-obojky.cz
