ErGear Electric Standing Desk

Instruction Manual

Models: EGESD25B / EGESD25WN, EGESD26B / EGESD26WN

Rev00(A)

Tools Needed (Not Included)

[Drill Icon] Drill
OR
[Phillips Screwdriver Icon] Phillips Screwdriver

Specifications

Feature	Value
Height Adjustment Range	28.4" - 46.5" (72-118cm)
Power Input	100V - 240V
Max. Speed	21mm/s
Operating Noise	≤52dB
Max. Load	176 lbs / 80 kg

Supplied Parts and Hardware

Step 1

A x 8: Bolt M6 x 12mm
B x 8: Bolt M6 x 42mm
01 x 1: Right Crossbar
02 x 1: Left Crossbar
03 x 1: Right Desk Leg
04 x 1: Left Desk Leg
05 x 2: Side Plate
06 x 2: Leg Base
C1 x 1: Allen Wrench (3/16")
C2 x 1: Allen Wrench (5/32")

Step 2

D x 4: Screw ST4.8 X 12mm
E x 8: Wood Dowel Pin
F x 2: Desktop Panel Connector
07 x 1: Desktop

Step 3

B x 1: Bolt M6 x 42mm
D x 11: Screw ST4.8 X 12mm
08 x 1: Fixed Rod
09 x 1: Middle Crossbar
C x 1: Large Allen Wrench (3/16")

Step 4

G x 2: Bolt M4 x 3.5mm
10 x 1: Transmission Rod
C3 x 1: Wrench

Step 5

D x 2: Screw ST4.8 X 12mm
11 x 1: Controller
12 x 1: Storage Hook

Step 6

D x 4: Screw ST4.8 X 12mm
13 x 1: Cable Management Tray

Step 7

14 x 1: AC Adapter
15 x 2: Cable Clip

Step 8

H x 4: Screw M6 x 35mm
16 x 1: Power Outlet Box

Step 9

17 x 1: Cable Hole Cover

Assembly Instructions

Step 1: Assembling the Leg Sections

Attach the crossbars.

Attach the Right Crossbar (01) and Left Crossbar (02) to the Right Desk Leg (03) and Left Desk Leg (04). Use Bolts (A) to secure them. Align the small round protrusions on the crossbars with the corresponding holes on the desk legs.

Attach the side plates.

Attach the Side Plates (05) to the desk legs. Use Bolts (B) and Allen Wrench (C1) for attachment.

Screw in Bolts (B) to secure the crossbars (06) to the desk legs. Do not fully tighten all four bolts until they are in place.

Slightly loosen the four pre-installed bolts on the crossbars.

Step 2: Assembling the Desktop

Connect the desktop panels.

Connect the two Desktop panels (07) using Wood Dowel Pins (E).

Secure the desktop panels.

Secure the Desktop panels (07) using Desktop Panel Connectors (F) and Screws (D). A drill or Phillips screwdriver can be used.

Step 3: Attaching the Frame to the Desktop

Position the frame components.

Place the Fixed Rod (08) and Middle Crossbar (09) on the underside of the assembled desktop, aligning screw holes.

Loosely attach the frame.

Loosely thread Bolts (B) through the Middle Crossbar (09) and Fixed Rod (08) into the desktop using Allen Wrench (C1).

Secure the frame.

Secure the frame components using Screws (D) and a drill or Phillips screwdriver.

Slide leg sections onto the middle crossbar.

Slide the two leg sections (01, 02) onto the Middle Crossbar (09).

Adjust and tighten.

Adjust the leg sections and ensure screw holes are aligned. Fully tighten the four pre-installed bolts on the crossbars securing the frame using Screws (D) and Allen Wrench (C2).

Secure the frame to the desktop.

Secure the frame to the desktop using Bolts (B) and Allen Wrench (C1) for the crossbars, and Bolts (D) and Allen Wrench (C2) for the leg sections.

Step 4: Attaching the Transmission Rod

Prepare the legs.

Measure leg heights. If unequal, insert the Transmission Rod (10) into the left leg and turn it clockwise to raise or anti-clockwise to lower the leg to match the right leg's height.

Connect the transmission rod.

Ensure the Transmission Rod (10) is inserted into the left leg. Slide the rod coupler to connect with the other end of the transmission rod. Use Wrench (C3) for fine-tuning if needed.

Step 5: Attaching the Controller and Storage Hooks

Attach the Controller (11) to the desktop using Screws (D). Attach the Storage Hook (12) to the desk leg using Screws (D).

Step 6: Attaching the Cable Management Tray

Fold the Cable Management Tray (13) along the dashed lines. Secure the tray to the desktop using Screws (D) with a drill or Phillips screwdriver.

Step 7: Connecting the Cables

Connect the Motor Cable to the Controller (11). Connect the AC Adapter (14) to the Controller. Use Cable Clips (15) to manage cables.

Step 8: Attaching the Power Outlet

Press the button on the Power Outlet Box (16) to open its cover. Loosen pre-installed bolts to separate the power outlet components.

Secure the Power Outlet Box (16) to the desktop using Screws (H).

Step 9: Installing the Cable Hole Cover

Install the Cable Hole Cover (17) into the desktop opening.

Using the Controller

Note: After initial power-on, the screen shows the current height. If displayed height is incorrect or legs are unequal, follow reset instructions.

Reset Procedure

Press and hold the [⬇️] button until the desk moves to its lowest level, then release the button.
Press and hold the [⬇️] button until 'rst' displays. Continue holding until the desk lowers and rises slightly. Release the button when the current height is displayed. Reset complete.

Save Current Height Setting

Press and hold the [⬆️] or [⬇️] button for 3 seconds. The screen will show 'S-1' or 'S-2'. Short-press the same button to move the desk to the saved height. Press any button to stop.

Raise the Desk

Press the [⬆️] button to raise the desk to its highest position (116cm) or until the button is released.

Lower the Desk

Press the [⬇️] button to lower the desk to its lowest position (72cm) or until the button is released.

Lock/Unlock

Press and hold the [⬆️] and [⬇️] buttons together for 5 seconds. The screen displays 'Loc' when locked, and buttons are disabled. Repeat to unlock.

Power-Saving Mode

The screen turns off after 1 minute of inactivity. Press any button to wake.

Protection Mode Error Codes

Code	Description
HOT	Overheating Protection: The motor stops to prevent overheating after prolonged use. Wait 18 minutes to cool before height adjustment.
rst	Reset Warning: Continue reset.
E11	Overloading Protection: Max load exceeded. Do not operate for 20 seconds. Remove items and follow reset instructions.
E12	Cable Disconnection Warning: Check motor/controller connections. Normal operation resumes when connectors are properly seated.
E14	Incline/Vibration Detection: Desk moves in opposite direction and stops if vibration, impact, or incline is detected.

	ErGear EGESD3 Electric Standing Desk Assembly and Operation Guide Comprehensive guide for assembling and operating the ErGear EGESD3 electric standing desk, including parts list, assembly steps, controller functions, and troubleshooting.
	48" Electric Standing Desk with Monitor Riser and Drawers - EGESD5B-1 / EGESD5V-1 Instruction Manual Comprehensive instruction manual for the ErGear 48" Electric Standing Desk (Models EGESD5B-1 / EGESD5V-1), detailing assembly, usage, and troubleshooting.
	ErGear Electric Standing Desk Instruction Manual Comprehensive instruction manual for the ErGear Electric Standing Desk (EGESD32/EGESD33), covering specifications, assembly, operation, safety, and troubleshooting. Includes detailed steps and error code explanations.
	ErGear Electric Standing Desk Instruction Manual & Assembly Guide Comprehensive guide for assembling, operating, and troubleshooting the ErGear Electric Standing Desk (Models EGESD4B, EGESD4V, EGESD4N). Includes parts list, step-by-step instructions, controller functions, and error code explanations.
	ErGear Electric Standing Desk Instruction Manual This manual provides instructions for assembling and using the ErGear Electric Standing Desk, including specifications, parts lists, assembly steps, controller operation, and troubleshooting.
	ErGear Electric Standing Desk Instruction Manual - Assembly and Operation Guide Comprehensive instruction manual for the ErGear Electric Standing Desk (Models EGESD8B, EGESD8V). Learn how to assemble, operate, and troubleshoot your height-adjustable desk.
	ErGear EGESD55B/EGESD55W Electric Standing Desk Frame: Assembly & User Manual Comprehensive instruction manual for the ErGear EGESD55B and EGESD55W electric standing desk frames. Learn how to assemble, use the controller, and troubleshoot common error codes for your adjustable height desk.
	Ergear Electric Standing Desk Assembly and User Manual Comprehensive guide for assembling and using the Ergear 48" / 63" Electric Standing Desk (Models EGESD5B, EGESD5V, EGESD5N, EGESD7B, EGESD7V, EGESD7N). Includes step-by-step instructions, specifications, controller functions, and troubleshooting error codes.