ErGear Electric Standing Desk
Instruction Manual
Models: EGESD4B / EGESD4V / EGESD4N
Specifications
- Height Adjustment Range: 28.3"-46.5" (72-118cm)
- Power Input: 100V-240V
- Max. Speed: 20mm/s
- Operating Noise: <55dB
- Max. Load: 176 lbs / 80kg
Supplied Parts and Hardware
Step 1: Desk Legs and Frame Components
- 01 x1 Crossbar
- 02 x1 Left Desk Leg
- 03 x1 Right Desk Leg
- 04 x2 Leg Base
- A x4 Bolt M6 x 11mm
- B x8 Bolt M6 x 35mm
- C x1 Large Allen Wrench 3/16" (5mm)
Step 2: Side Plates and Transmission Rod
- 05 x2 Side Plate
- 06 x1 Transmission Rod
- D x1 Small Allen Wrench 5/64" (2mm)
- E x10 Rubber Pad
Step 3: Desktop and Control Components
- 07 x1 Desktop
- 08 x1 Controller
- F x20 Screw M5 x 16mm
- G x4 Wood Dowel Pin
- H x2 Desktop Panel Connector
- I x2 Headset Hook
Step 4: Power and Cable Management
- 09 x1 AC Adapter
- J x2 Cable Clip
Step 5: Cable Hole Covers
- K x2 Cable Hole Cover
Assembly Instructions
Step 1: Assembling and Connecting the Desk Legs
Assemble the crossbar (01) to the left desk leg (02) and right desk leg (03) using bolts (A) and the large Allen wrench (C). Attach the leg bases (04) to the bottom of each desk leg using bolts (B) and the large Allen wrench (C). This step may require assistance due to the weight. ⚠️
Step 2: Attaching the Side Plates and the Transmission Rod
Attach the side plates (05) to the top of the desk legs using bolts (A) and the large Allen wrench (C). Ensure the transmission rod (06) is properly inserted. Before connecting, measure the heights of both desk legs to ensure they are level. If not, adjust the transmission rod: turn clockwise ? to lower the left leg or anti-clockwise to raise it until it matches the right leg's height. Connect one end of the transmission rod to the left leg's mechanism and the other end to the right leg's motor drive shaft. Secure the transmission rod to the motor drive shaft by turning the set screw clockwise using the small Allen wrench (D). Tighten the coupling nut (E) to ensure a secure fit.
Step 3: Assembling and Attaching the Desktop
Assemble the desktop (07) by inserting wood dowel pins (G) and securing with screws (F) using a drill (not included). Then, attach the assembled desktop to the frame using screws (F). Attach the controller (08) and desktop panel connector (H) to the underside of the desktop using screws (F). Attach the headset hook (I) to the desktop using screws (F).
Step 4: Connecting the Cables
Connect the AC adapter (09) to the controller (08). Use cable clips (J) to manage the wiring neatly. Connect the motor cables to the controller. Ensure all connections are secure.
Step 5: Installing the Cable Hole Covers
Place the cable hole covers (K) into the designated holes on the desktop. ➡️
Using the Controller
The controller allows you to adjust the desk height and save preferred positions.
- Save Current Height Setting: Short-press the 'S' button. The display will flash. Press '1', '2', or '3' to save the current height to that preset.
- Select Height Setting 1: Press the '1' button. The desk will move to the saved height.
- Select Height Setting 2: Press the '2' button. The desk will move to the saved height.
- Select Height Setting 3: Press the '3' button. The desk will move to the saved height.
- Raise the Desk: Press the 'A' button to raise the desk continuously until it reaches the highest position (46.5" / 118cm) or until released. ⬆️
- Lower the Desk: Press the 'V' button to lower the desk continuously until it reaches the lowest position (28.3" / 72cm) or until released. ⬇️
Settings and Troubleshooting
Settings
- Change Display Height Units: Press and hold the 'S' button until 'S-' flashes. Press 'S' to select. Press 'A' or 'V' to toggle between 'IN' (imperial) and 'SI' (metric). Press 'S' to save.
- Change Collision Detection Sensitivity: Press and hold the 'S' button until 'S-' flashes. Press 'S' to select. Press 'A' or 'V' to toggle between 'CF' (collision force) and then press 'A' or 'V' again to select sensitivity levels (off, low, normal, high). Press 'S' to save.
- Reset: Press and hold the 'V' button for 5 seconds. The screen will show 'RES'. Continue holding until the desk moves to its lowest level and then rises slightly.
Protection Mode Error Codes
| Code | Description |
|---|---|
| Hot | Overheating Protection: The motor stops after 2 minutes of continuous operation to prevent damage. Wait at least 18 minutes before making further adjustments. |
| E10 | Sensor Malfunction Warning: Motor safety sensor not detected. Power off, check the connection between the motor and controller, and power back on. |
| E20 | Overloading Warning: Maximum load exceeded. If raising the desk, remove items and try again. If lowering, power off, remove items, power back on, and try again. |
| E02 | Operation Status Warning: Desk stops due to detected vibration, impact, or incline. If incorrect, follow the reset instructions. |
| E32 | Overvoltage Protection: Input voltage too high. If using the correct AC adapter, power off, check power and controller connections, then power on. |
| E31 | Undervoltage Protection: Input voltage too low. If using the correct AC adapter, power off, check power and controller connections, then power on. |
| E60 | Unequal Leg Height Warning: Power off the desk, check if left and right legs are at the same height. Adjust if necessary following instructions. Power on again. |
| - | Cable Disconnection Warning: Check motor and controller cable connections. Normal operation should resume once all connectors are properly connected. |
