Ergear Electric Standing Desk Instruction Manual

Technical Support

(US/CA) 1-800-651-9525 Mon-Fri, 8am-8pm (CST)

(UK) 44-808-196-3875 Mon-Fri, 2pm-10pm (UTC)

Other Info: support@ergear.com

Website: https://ergear.com

Tools Needed (Not Included)

A Phillips screwdriver or a drill is required for assembly.

Specifications

• Height Adjustment Range: 28.3"-46.5" (72-118cm)
• Power Input: 100V-240V
• Max. Speed: 20 mm/s
• Operating Noise: <55 dB
• Max. Load: 176 lbs / 80 kg

Assembly Instructions

Step 1: Assembling and Connecting the Desk Legs

Supplied Parts and Hardware:

• 01 Crossbar x 1
• 02 Left Desk Leg x 1
• 03 Right Desk Leg x 1
• 04 Leg Base x 2
• Bolt A (M6 x 11mm) x 4
• Bolt B (M6 x 35mm) x 8
• Large Allen Wrench C (3/16" / 5mm) x 1

Attach the crossbar (01) to the left desk leg (02) and right desk leg (03) using Bolts A. Ensure the orientation is correct as shown in the diagram. Attach the leg bases (04) to the bottom of each leg using Bolts B and the Large Allen Wrench C. Note: This step may require assistance due to the weight of the components.

Step 2: Attaching the Side Plates and the Transmission Rod

Supplied Parts and Hardware:

• Side Plates (part of 05) x 2
• Bolt A (M6 x 11mm) x 4
• Small Allen Wrench D (5/64" / 2mm) x 1
• Transmission Rod 06 x 1
• Coupling Nut (part of 06)

Attach the side plates (05) to the top of the desk legs using Bolts A and the Large Allen Wrench C. Insert the transmission rod (06) into the hole in the left leg. Ensure the heights of both legs are level before proceeding. Turn the rod clockwise to lower the left leg or anti-clockwise to raise it. Connect the other end of the transmission rod to the motor drive shaft on the right leg. Ensure the set screw faces outwards. Secure the transmission rod to the motor drive shaft by turning the set screw clockwise using the Small Allen Wrench D. Tighten the coupling nut to fine-tune the transmission rod fit.

Step 3: Assembling the Desktop

Supplied Parts and Hardware:

• Desktop 07 x 1 (may be two panels)
• Wood Dowel Pins G x 4 (for 48" desk) or x 6 (for 63" desk)
• Desktop Panel Connector H x 2

For the 48" desk, use four wood dowel pins (G) to join the two desktop panels. For the 63" desk, use six wood dowel pins (G). Insert the dowel pins into the pre-drilled holes on the edges of the desktop panels and align the panels. The diagram shows how to insert the dowel pins and join the panels.

Step 4: Attaching the Desktop

Supplied Parts and Hardware:

• Screw F (M5 x 16mm) x 16
• Desktop Panel Connector H x 2
• Storage Hook I x 2
• Controller 08 x 1

Place the assembled desktop onto the assembled frame. Secure the desktop to the frame using Screws F. Use a drill or Phillips screwdriver. Attach the desktop panel connectors (H) to join the desktop panels if applicable, using Screws F. Attach the storage hooks (I) and the controller (08) to the underside of the desktop using Screws F.

Step 5: Connecting the Cables

Supplied Parts and Hardware:

• AC Adapter 09 x 1
• Cable Clip J x 2

Connect the motor cable to the controller (08). Connect the AC adapter (09) to the controller. Use the cable clips (J) to manage and secure the cables neatly along the frame and underside of the desk.

Step 6: Installing the Cable Hole Covers

Supplied Parts and Hardware:

• Cable Hole Cover K x 2

Insert the cable hole covers (K) into the designated holes on the desktop.

Using the Controller

The controller allows you to adjust the desk height and save preferred positions.

• Save Current Height Setting: Short-press the '8' button (memory button), the display will flash. Press one of the number buttons (1, 2, or 3) to save the current height to that preset.
• Select Height Setting 1: Press the '1' button. The desk will move to the saved height for preset 1.
• Select Height Setting 2: Press the '2' button. The desk will move to the saved height for preset 2.
• Select Height Setting 3: Press the '3' button. The desk will move to the saved height for preset 3.
• Raise the Desk: Press and hold the up arrow button (?). The desk will move upwards until the button is released or the maximum height (46.5" / 118cm) is reached.
• Lower the Desk: Press and hold the down arrow button (?). The desk will move downwards until the button is released or the minimum height (28.3" / 72cm) is reached.

Settings

Change Display Height Units

Press and hold the '8' button until 'S-' is displayed and flashing. Press '8' again, and 'Un' is displayed. Press '8' to select. Use the up (?) or down (?) arrow buttons to switch between 'IN' (imperial) and 'SI' (metric). Press '8' to save your choice.

Change Collision Detection Sensitivity

Long press the '8' button until 'S-' shows and flashes. Press '8' again, and the display shows 'Un.' Press the up (?) or down (?) arrow buttons to switch to 'CF.' Press '8' to select. Use the up (?) or down (?) arrow buttons to switch between 'OFF,' Low (L), Normal (n), or Heavy (H) collision force detection. Press '8' to save your choice.

Reset

Press and hold the '✓' (check/reset) button for 5 seconds. The screen will show 'RES.' Continue holding until the desk moves to its lowest level and then rises slightly.

Protection Mode Error Codes

Product Information

Thank you for choosing Ergear. We strive to provide the best quality products and service.