Sygonix RFID/Codeslot IP66 Programming Codes Overview
Product Number: 3214306
Important Information
All programming must be performed in programming mode. To start programming mode, enter the master code twice during normal operation (normal use: "1234").
To reset the master code to factory settings, disconnect the codeslot from the power supply. Press and hold the button while reconnecting the power to the codeslot. Hold the button for another 3 seconds. The master code is reset when the codeslot emits a short beep and the right LED turns green again.
Programming Codes Overview
| Programmer Code | Programmer Code | Programming Function | Values | Input | Default Setting |
|---|---|---|---|---|---|
| *9 | *4 | Change code length | 2-6 / 2-6 digits | *9 04 [e.g., 2 digits] |
4 digits |
| *9 | *5 | Program the master transponder card | Read card | *9 05 [Read card] |
— |
| *9 | *6 | Delete the master transponder card | Read card | *9 06 [Read card] |
— |
| *9 | *7 | Change master code | Enter master code | *9 07 [Enter master code] |
— |
| *9 | *3 | Program transponder card or user code for relay output #1 | 000-999 (User ID) | *9 03 [User ID] |
— |
| *9 | *3 | Program user code for relay output #1 - 2nd option | 00-999 (User ID) | *9 03 [User ID] |
— |
| *9 | *4 | Program transponder card or user code for relay output #1 | 0-999 (User ID) | *9 04 [User ID] |
— |
| *9 | *4 | Program user code for relay output #1 - 2nd option | 0-09 (User ID) | *9 04 [User ID] |
— |
| *9 | *5 | Program transponder card or user code for relay output #2 | 00-09 (User ID) | *9 05 [User ID] |
— |
| *9 | *5 | Program user code for relay output #2 - 2nd option | 00-999 (User ID) | *9 05 [User ID] |
— |
| *9 | *6 | Program a number of transponder cards for relay output #1 | 000 (Quantity) | *9 06 [Quantity] |
— |
| *9 | *7 | Program a number of transponder cards with sequential serial numbers for relay output #1 | 0-09 (Quantity) | *9 07 [Quantity] |
— |
| *9 | *8 | Delete a user - relay output #1 | 000-999 (User ID) | *9 08 [User ID] |
— |
| *9 | *8 | Delete a user - relay output #2 | 00-999 (User ID) | *9 08 [User ID] |
— |
| *9 | *9 | Delete all users | ... | *9 09 ## |
— |
| *1 | *5 | Activation duration - relay output #1 | 0-99 (seconds) or for toggle operation | *1 05 [0-99 seconds] (for toggle operation) |
1 second |
| *1 | *5 | Activation duration - relay output #2 | 0-99 (seconds) or for toggle operation | *1 05 [0-99 seconds] (for toggle operation) |
1 second |
| *2 | — | Activate/deactivate backlight | 1 = deactivate, 2 = activate | *2 01 [deactivate], *2 02 [activate] |
Backlight activated |
| *2 | — | Activate/deactivate signal tones | 1 = deactivate, 2 = activate | *2 03 [deactivate], *2 04 [activate] |
Signal tones activated |
| *6 | *2 | Activate/deactivate tamper protection | 1 = deactivate, 2 = activate | *6 01 [deactivate], *6 02 [activate] |
Tamper protection activated |
| *3 | — | Reset codeslot to factory settings | ... | *3 ## |
— |
Additional Information
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).
All rights, including translation, reserved. Reproduction of any kind, for example, photocopying, microfilming, or recording in electronic data processing equipment, requires the written consent of the publisher. Reprinting, also of excerpts, is prohibited. The publication complies with the technical state at the time of printing.
Copyright 2024 by Conrad Electronic SE.
Document version: *3214306_V2_0625_02_m_dm_prog_NL
