Sygonix RFID/Codeslot IP66 Programming Codes Overview
Product Number: 3214306
Important Information
All programming must be performed in programming mode. To start programming mode during normal operation, enter the master code twice (default "1234").
To reset the master code to factory settings, disconnect the codeslot from the power supply. Press and hold the button while reconnecting the power supply to the codeslot. Continue holding the button for another 3 seconds. The master code is reset when the codeslot emits a short beep and the right LED turns green again.
Programming Codes Overview
| Program Code | Program Code | Programming Function | Values | Input | Default Setting |
|---|---|---|---|---|---|
| *9 | 4 | Change code length | 2-6 / 2-6 digits | *9 4 [2-6 digits] (e.g., 2 digits) | 4 digits |
| *7 | — | Program master transponder card | Card read | *7 Card read | — |
| *7 | — | Remove master transponder card | Card read | *7 Card read | — |
| *0 | 2 | Change master code | Master code | *0 2 [New Master Code] | Master code |
| *0 | 0 | Enter master code | Master code | *0 0 [Master Code] | — |
| *1 | 2 | Program transponder card or user code for relay output #1 | 000-999 (User ID) | *1 2 [User ID] | — |
| *1 | 3 | Program user code for relay output #1 - 2nd possibility | 00-999 (User ID) | *1 3 [User ID] | — |
| *1 | 4 | Program transponder card or user code for relay output #1 | 0-999 (User ID) | *1 4 [User ID] | — |
| *1 | 5 | Program transponder card or user code for relay output #2 | 0-999 (User ID) | *1 5 [User ID] | — |
| *1 | 6 | Program user code for relay output #2 - 2nd possibility | 0-09 (User ID) | *1 6 [User ID] | — |
| *1 | 7 | Program user code for relay output #2 - 2nd possibility | 00-09 (User ID) | *1 7 [User ID] | — |
| *1 | 8 | Program transponder card or user code for relay output #1 | 00-999 (User ID) | *1 8 [User ID] | — |
| *5 | 1 | Program a number of transponder cards for relay output #1 | 000 (Quantity) | *5 1 [Quantity] | — |
| *5 | 2 | Program a number of transponder cards with consecutive serial numbers for Relay output #1 | 000 (Quantity) | *5 2 [Quantity] | — |
| *3 | 1 | Delete a user - relay output #1 | 000-999 (User ID) | *3 1 [User ID] | — |
| *3 | 2 | Delete a user - relay output #2 | 000-999 (User ID) | *3 2 [User ID] | — |
| *3 | 3 | Delete all users | ... | *3 3 | — |
| *5 | 3 | Activation duration - relay output #1 | 0-99 (seconds) or for toggle operation | *5 3 [Seconds] or *5 3 0 [toggle operation] | 1 second |
| *5 | 4 | Activation duration - relay output #2 | 0-99 (seconds) or for toggle operation | *5 4 [Seconds] or *5 4 0 [toggle operation] | 1 second |
| *2 | 1 | Activate/deactivate background lighting | 2 = activate, 1 = deactivate | *2 1 2 [activate background lighting] or *2 1 1 [deactivate background lighting] | Background lighting activated |
| *2 | 2 | Activate/deactivate signal tones | 2 = activate, 1 = deactivate | *2 2 2 [activate signal tones] or *2 2 1 [deactivate signal tones] | Signal tones activated |
| *2 | 3 | Activate/deactivate sabotage protection | 2 = activate, 1 = deactivate | *2 3 2 [activate sabotage protection] or *2 3 1 [deactivate sabotage protection] | Sabotage switch activated |
| *2 | 4 | Reset codeslot to factory settings | ... | *2 4 | — |
This is a publication from Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com). All rights, including translation, reserved. Reproduction of any kind, e.g. photocopying, microfilming or recording in electronic data processing equipment, requires written permission from the publisher. Reprinting, also of excerpts, is prohibited. The publication corresponds to the technical status at the time of printing. Copyright 2024 by Conrad Electronic SE.
