Product Overview
This document provides instructions and specifications for the MI Computer Monitor Light Bar.
A sleek, modern light bar designed to attach to a computer monitor. It features a minimalist design with a matte finish and an adjustable arm.
The package typically includes the light bar, a Type-C charging cable, a remote control, and requires two AAA batteries (sold separately) for the remote.
Note: Illustrations and product details are for reference and may vary due to enhancements.
Installation
1. Install the light bar
With the light area facing downwards, attach the power contact points on the light bar to those in the base.
Diagram showing the MI Computer Monitor Light Bar being attached to a monitor. The light bar connects to a weighted base via a gravity shaft. The base features a clamp mechanism that attaches to the top edge of the monitor. Dimensions indicate compatibility with monitors up to 32mm thick.
Place the base on the upper center of the monitor. Ensure the clamp is firmly secured on the monitor, with the bottom of the base against the back of the monitor.
Notes on Installation:
- This product is compatible with monitors up to 32 mm in thickness, including hairtail monitors, curved monitors, and iMacs.
- For monitors less than 10 mm in thickness, the light bar can be supported, but the bottom of the base may not be against the monitor.
- The angle of the gravity shaft on the base can be adjusted by 40°. Avoid excessive force.
- This product is not designed for use with laptops.
1.2 Install the remote control batteries
- Place the remote control with the anti-slip pad facing downwards on your palm. Turn the remote control counterclockwise with another hand to open the back cover.
- Install two AAA batteries (sold separately), ensuring the positive (+) and negative (-) poles are correctly oriented.
- Replace the back cover, aligning the triangle on the bottom with the lock symbol on the anti-slip pad.
- Turn the remote control clockwise with another hand to secure the back cover.
Illustrations demonstrate how to open and close the remote control's battery cover by rotating it. The battery compartment is shown with indicators for correct AAA battery placement.
How to Use
2.1 Connect to power supply
Connect the charging cable to the power port on the light bar and then plug it into a power supply.
Diagram showing the MI Computer Monitor Light Bar connected to a power source via its Type-C charging cable.
Power Notes:
- The product can be powered by an adapter, power bank, or computer USB port with an output voltage of 5 V and an output current greater than 1 A. Power supplies must be Safety Extra Low Voltage (SELV) and have a peak voltage not exceeding 5.25 V.
- Use the original charging cable. Do not use USB extension cables or splitters, as they may cause the light bar to malfunction.
- Avoid fast charging cables that do not output 5 V by default.
- If the light bar flickers or makes noise, replace the power supply devices promptly.
- Do not connect the power contact points on the light bar or base to other metallic conductors to prevent damage or hazards.
- The original charging cable is designed exclusively for the Mi Computer Monitor Light Bar; it does not support fast charging or data transmission.
2.2 Control the light
Press the knob on the remote control to turn the light on/off.
After turning on the light:
- Rotate the knob to adjust brightness.
- Press and hold the knob, then simultaneously rotate it to adjust color temperature.
- Press and hold the knob for two seconds to set the light to a recommended configuration: 2700 K color temperature and 50% brightness.
Note: The remote control and light bar are paired by default. If pairing is needed with a non-original accessory of the same model, press and hold the knob on the remote control within 20 seconds after turning on the light. Slow blinking indicates successful pairing.
2.3 Adjust the angle
Rotate the light bar to adjust its angle. It has an adjustment range of 25°.
Specifications
- Model: MJGJD01YL
- Operating Temperature: -10°C to 40°C
- Operating Humidity: 0-85% RH
- Service Life: 25,000 hours
- Power Factor: > 0.9
- Rated Power: 5 W (80 × 0.2 W / LED module)
- Light Bar Dimensions: ø 23 × 448 mm
- Remote Control Dimensions: ø 66.5 × 34 mm
- Color Temperature: 2700-5000 K
- Color Rendering Index: Ra95
- Luminous Flux: 270 lm
- Rated Input: 5 V 1 A
- Wireless Connectivity: 2.4 GHz
- Operating Frequency: 2405-2470 MHz
- Maximum Output Power: 7.94 dBm
Precautions
- One remote control can manage multiple light bars, but each light bar can only be controlled by one remote at a time.
- When cleaning the light bar's surface, use a soft cotton cloth. Avoid corrosive solvents.
- When installing or moving the light bar, handle both the light bar and base carefully to prevent product damage or personal injury from falling parts.
- Ensure batteries are installed with the correct polarity (+/-) in the remote control.
- Non-rechargeable batteries should not be recharged. Do not mix battery types or old and new batteries.
- If the remote control malfunctions, the battery level may be low. Replace batteries with new ones and dispose of old batteries according to local regulations to prevent environmental pollution.
- After replacing remote control batteries, recycle old batteries to avoid environmental pollution.
- Remove batteries from the remote control if it will not be used for an extended period or is being disposed of.
- Dispose of leaking batteries from the remote control according to local rules and regulations to avoid environmental pollution.
- The light source in this luminaire should only be replaced by the manufacturer, their service agent, or a similarly qualified person.
- This product is intended for indoor use only.
- Under normal conditions, maintain a separation distance of at least 20 cm between the antenna and the user's body.
- When installing the light bar onto the base, ensure the power contact points on both parts are correctly aligned.
Compliance and Disposal
Manufactured for: Xiaomi Communications Co., Ltd.
Manufactured by: Qingdao Yeelink Information Technology Co., Ltd. (a Mi Ecosystem company)
Address: 10F-B4, Building B, Qingdao International Innovation Park, No. 1 Keyuan Weiyi Road, Laoshan District, Qingdao City, Shandong Province, P. R. China. For more information, visit www.mi.com.
EU Declaration of Conformity
Qingdao Yeelink Information Technology Co., Ltd. declares that the radio equipment type MJGJD01YL complies with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at: https://www.mi.com/en/service/support/declaration.html.
Importer
Beryko s.r.o.
Na Roudné 1162/76, 301 00 Plze
WEEE Disposal and Recycling
Products bearing the WEEE symbol are waste electrical and electronic equipment. They should not be mixed with unsorted household waste. Protect human health and the environment by handing over waste equipment to a designated collection point for recycling, appointed by government or local authorities. Correct disposal and recycling help prevent negative consequences to the environment and human health. Contact local authorities for more information.
Documents / Resources
- MI Computer Monitor Light Bar [PDF] User Manual
- Computer Monitor Light Bar
References
User Feedback
A user named Shaq reported an issue where the remote control stopped working after a few months, even after replacing the batteries.
The document also includes sections for leaving comments and user input, though no further specific feedback is detailed in the provided text.
Beryko.cz
Xiaomi United States | Xiaomi Official Website
adssettings.google.com/whythisad?source=display&reasons=AS7gl4Kx4JhWdlbtTaZP6tB0MUzY_PK6EbhOrEPzav2QX9OokIIiqMXXLt2UyC66QgvWkroB-0_Ej2ebvMu1Er7zz_5xSj11HVOuOamQJOUOP1JPYdviiFw3anzo0XtPcRiFLGI8hHzkOJb3renOsRqNiDNHbSWQz_CgvBI3QpmqYUDhDC9Tgmmik9jggn5k
googleadservices.com/pagead/aclk?sa=L&ai=CwMfM957pYravFY6N7wKJmou4Aoixwe1iqPndjb4QhIXstt4LEAEgy4nWI2DJpvWLzKTUGaABieiV7wPIAQmoAwHIA8sEqgTyAU_QEdV5lOYTlUyNrPDd8AqPJG-OecRu9L_iO9sb8EBNDLvUMz1xfTdG47zvV7cw2mHESk4UobuRVdK-Em1WY-pgE7b2wDSpynB5yu7KT1
