Xiaomi Mi Computer Monitor Light Bar

Overview

Please read the following manual carefully. Keep the manual for future reference.

Diagram Description: Illustration showing the components of the Xiaomi Mi Computer Monitor Light Bar. Key parts include the lamp bar, the adjustable clamp for attaching to a monitor, the base, the USB-C charging port on the lamp, the power connector, the wireless remote control, and the USB-C charging cable. The remote requires 2x AAA batteries (not included).

Note: Batteries are not included. Images and user interface are for illustration purposes only. Images and illustrations may vary by model.

Installation

1. Installing the Lamp

Place the base onto the top center of the monitor. Attach the lamp using the clamp. Securely clip the bottom part of the clamp onto the back of the monitor. Ensure the lamp is safely attached.

Diagram Description: Illustration demonstrating how the lamp's clamp attaches to the monitor. The clamp is designed to fit monitor edges up to 32mm thick. The diagram shows the clamp mechanism securing the lamp to the monitor's rear edge.

• Note: 1) The device is compatible with flat, curved, and iMacs monitors up to 32 mm thick. 2) Monitors less than 10 mm thick can also be used (the bottom part of the clamp may not rest on the monitor). 3) The bottom part of the clamp can extend up to a 40° angle. 4) The device cannot be used on laptops.

2. Inserting Batteries into the Wireless Remote

Take the wireless remote. A lock symbol is shown on the bottom of the remote. Hold the bottom part of the remote with one hand and rotate the anti-slip cover counter-clockwise.

Insert 2x AAA batteries. Ensure correct polarity.

Replace the cover onto the bottom of the remote, aligning the lock symbol with the mark on the bottom edge.

Rotate the cover clockwise (hold the bottom part of the remote with your other hand).

Diagram Description: Diagram illustrating the process of opening and closing the battery compartment of the wireless remote. It shows the counter-clockwise rotation to open and clockwise rotation to close the cover.

Usage

1. Powering On

Connect the charging cable to the lamp's port. Then, plug the other end of the cable into a power source.

Note: The device can be charged via: a power bank, an adapter, or a computer with a 5V output voltage and a current greater than 1A. The charging device must comply with SELV standards, and the voltage must not exceed 5.25V. Please use the original charging cable. Do not use splitters or USB extensions, as this may cause the device to malfunction. Do not use fast charging adapters (only 5V). If the device emits strange sounds or the light flickers, try a different power source. Keep the magnetic contacts of the base and lamp away from other magnetic or metallic objects to avoid damage to the device or injury. The included original power cable is intended solely for the Mi Computer Light Bar.

2. Controlling the Light

To turn the device on/off: press the top of the wireless remote. To adjust brightness: rotate the remote.

To adjust light temperature: press and rotate the remote. To set 50% brightness and 2700K light temperature: press and hold the remote for 2 seconds.

Note: The lamp and wireless remote are already paired. No pairing is required.

Pairing with an additional non-original remote of the same model: Press and hold the remote for 20 seconds. Flashing light indicates pairing.

3. Adjusting the Angle

The lamp can be rotated by an angle of 25°.

Diagram Description: Illustration showing the lamp head can be tilted to adjust the light angle, with a range of 25 degrees.

Important Information and Specifications

Warnings and Notes

• One wireless remote can control multiple lamps. However, each lamp can only be controlled by one remote at a time.
• Clean the lamp with a soft, dry cloth. Do not use any chemicals.
• If you transport the lamp, carry it with its base.
• When inserting batteries, ensure correct polarity.
• Do not mix old and new batteries. Always use new ones. Do not attempt to recharge non-rechargeable batteries.
• If the remote malfunctions, insert new batteries. Recycle used batteries according to applicable regulations.
• Depleted batteries must be replaced with new ones. If the device is not used for a long time, remove the batteries.
• Immediately remove and replace any damaged batteries.
• Do not disassemble the device.
• The device is intended for indoor/room use only.
• Install the device at least 20 cm away from people or antennas.
• Ensure the lamp and base connectors are properly inserted.

Specifications