Mi Computer Monitor Light Bar

Package Contents

• Type-C Charging Cable
• Remote Control (with knob)
• AAA Batteries x2 (sold separately)

Note: AAA batteries are not included and must be purchased separately. Illustrations are for reference only; actual products may vary.

Installation

1. Install the Light Bar

• Attach the light bar to the base, ensuring the power contact points align. The light area should face downwards.
• Place the base on the upper center of the monitor. Secure the clamp firmly, ensuring the bottom of the base rests against the back of the monitor.

Compatibility Notes:

• Suitable for monitors up to 32 mm thick, including hairtail, curved, and iMac monitors.
• For monitors less than 10 mm thick, the base bottom may not contact the monitor.
• The gravity shaft angle is adjustable up to 40°. Avoid excessive force.
• Not compatible with laptops.

2. Install Remote Control Batteries

1. Open the remote control's back cover by placing it on your palm (anti-slip pad down) and turning the cover counterclockwise.
2. Insert two AAA batteries, observing correct polarity (+ and -).
3. Replace the back cover, aligning the triangle with the lock symbol.
4. Secure the back cover by turning it clockwise.

How to Use

1. Connect to Power Supply

Connect the charging cable to the power port on the light bar and plug it into a power supply.

Notes:

• Power sources: Adapter, power bank, or computer USB port with 5V output and at least 1A current. Power supplies must be Safety Extra Low Voltage (SELV) with a peak voltage not exceeding 5.25V.
• Use the original charging cable. Avoid USB extension cables or splitters, which may cause malfunction.
• Do not use fast charging cables that do not output 5V by default.
• If the light bar flickers or makes noise, replace the power supply.
• Do not connect power contact points to other metallic conductors to prevent damage or hazards.
• The original charging cable is for the Mi Computer Monitor Light Bar only; fast charging and data transmission are not supported.

2. Control the Light

• Press the knob to turn the light on/off.
• Rotate the knob to adjust brightness.
• Press and hold the knob while rotating to adjust color temperature.
• Press and hold the knob for two seconds to set the light to 2700K color temperature and 50% brightness.

Pairing Note: The remote and light bar are pre-paired. For re-pairing with a non-original accessory of the same model, press and hold the knob within 20 seconds of turning on the light. Slow blinking indicates successful pairing.

3. Adjust the Angle

Rotate the light bar to adjust its angle. The adjustment range is 25°.

Specifications

• Model: MJGJD01YL
• Operating Temperature: -10°C to 40°C
• Operating Humidity: 0-85% RH
• Service Life: 25,000 hours
• Power Factor: > 0.9
• Rated Power: 5 W (80 × 0.2 W / LED module)
• Light Bar Dimensions: ø 23 × 448 mm
• Remote Control Dimensions: ø 66.5 × 34 mm
• Color Temperature: 2700–6500 K
• Color Rendering Index: Ra95
• Luminous Flux: 270 lm
• Rated Input: 5V 1A
• Wireless Connectivity: 2.4 GHz
• Operating Frequency: 2405–2470 MHz
• Maximum Output Power: 7.94 dBm

Manufacturer Information:

• Manufactured for: Xiaomi Communications Co., Ltd.
• Manufactured by: Qingdao Yeelink Information Technology Co., Ltd. (a Mi Ecosystem company)
• Address: 10F-B4, Building B, Qingdao International Innovation Park, No. 1 Keyuan Weiyi Road, Laoshan District, Qingdao City, Shandong Province, P. R. China

For further information, please visit www.mi.com.

Precautions

• One remote can control multiple light bars, but a light bar can only be controlled by one remote.
• Clean the light bar surface with a soft cotton cloth. Avoid corrosive solvents.
• Handle the light bar and base with care during installation or moving to prevent damage or injury from falling parts.
• Ensure correct battery polarity (+/-) when installing in the remote control.
• Non-rechargeable batteries cannot be recharged. Do not mix battery types or old and new batteries.
• If the remote control malfunctions, replace the batteries. Dispose of used batteries according to local regulations to prevent environmental pollution.
• Recycle used batteries after replacement.
• Remove batteries from the remote control if it will not be used for an extended period or when disposing of it.
• Dispose of leaking batteries according to local rules and regulations.
• The light source should only be replaced by the manufacturer, service agent, or qualified personnel.
• This product is intended for indoor use only.
• Maintain a separation distance of at least 20 cm between the antenna and the user's body during normal operation.
• Ensure power contact points on the light bar and base are correctly aligned during installation.

Importer:

Beryko s.r.o.
Na Roudné 1162/76, 301 00 Plzeň
www.beryko.cz

EU Declaration of Conformity

Qingdao Yeelink Information Technology Co., Ltd. declares that the radio equipment type MJGJD01YL complies with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at: https://www.mi.com/en/service/support/declaration.html.

WEEE Disposal and Recycling

Products with the WEEE symbol are waste electrical and electronic equipment and should not be mixed with household waste. Dispose of waste equipment at designated collection points for recycling, as appointed by government or local authorities. Proper disposal and recycling help prevent negative environmental and health consequences. Contact local authorities for information on collection points and their terms.