Sylvox S40MCMA0 Installation Instructions
Model: S40MCMA0 | Compatible TV Screen: 42"-55" | Weight Capacity: 80KG/176LBS | VESA: 100x100 - 700x500mm
Product Overview
This document provides detailed installation instructions for the Sylvox S40MCMA0 rolling TV stand. It is designed for 42-inch to 55-inch screens and supports a weight capacity of up to 80KG (176LBS). The VESA mounting pattern compatibility ranges from 100x100mm to 700x500mm.
Note: Sylvox reserves the right to make modifications and changes to the product and instructions without prior notification. Please do not alter these instructions.
Important Safety Warnings
Warning! Improper assembly or installation can lead to serious injury, death, or property damage. Please read all instructions and warnings carefully before proceeding.
- If you are unsure about any part of the instructions or have questions, contact a qualified local installer.
- Do not assemble or install if any parts are damaged or missing. Contact your local dealer for assistance.
- This product is suitable for 42"-55" LCD/Plasma screens with a weight capacity of 80KG/176LBS.
- Do not use this product for any purpose other than its intended design.
- Sylvox disclaims any legal responsibility for damages or injuries resulting from product modifications, improper installation, exceeding the specified weight capacity, or misuse.
- Risk of Toppling: If children or teenagers climb on the furniture, or if objects are placed on it, the furniture may topple, resulting in serious injury or death.
- Changing the installation location or reinstalling in a place that cannot support its weight may cause the furniture to topple, resulting in serious injury or death.
- Ensure the stand is placed on a solid and level ground to maintain balance.
- Surface rust may appear on parts used outdoors. In severe weather conditions (strong winds, heavy rain), take additional protective measures to prevent potential damage.
- In case of any discrepancies between illustrations and the actual product, refer to the actual product.
Tools and Actions
Required Actions: [Tighten Direction] [Loosen Direction] [Screwdriver] [Tape Measure] [Adjustment] [Manual Operation] [Hex Wrench]
Bill of Materials
Verify all parts are present before assembly:
| Part ID | Description | Quantity | Dimensions/Type |
|---|---|---|---|
| A1 | Main Plate | 1 | |
| A2 | Wheel Bolt | 10 | M8x20mm |
| B1 | Screw | 4 | M8x20mm |
| C1 | Screw | 4 | M8x20mm |
| C2 | Screw | 2 | Φ8x1.5mm |
| D1 | Screw | 4 | M6x10mm |
| D2 | Screw | 2 | M5x10mm |
| E1 | Wheel | 4 | |
| F1 | Screw | 4 | M8x25mm |
| F2 | Screw | 4 | M6x25mm |
| G1 | Screw | 4 | M5x25mm |
| G2 | Screw | 4 | M4x25mm |
| H1 | Washer | 4 | Φ15×Φ8.2×10mm |
| H2 | Washer | 4 | Φ5×1mm |
Assembly and Installation
1. Install the Wheels
Attach the 4 wheels (E1) to the bottom of the stand's legs. Use the A2 bolts (M8x20mm) and the provided hex wrench to secure them. Tighten firmly.
Diagram Description: Shows a wheel being attached to the end of a leg. An upward arrow indicates the direction of attachment. Part A2 and a wrench are visible.
2. Mounting Tray
Attach the mounting tray to the base structure using part A1 and B1 screws (M8x20mm).
Diagram Description: Close-up views showing a horizontal tray being attached to the main base frame with screws.
3. Install the Pillar
Attach the vertical pillar components to the base. Use part A1 and screws C1 (M8x20mm) and C2 (Φ8x1.5mm) as indicated. Ensure correct orientation (Left/Right if applicable).
Diagram Description: Shows the two vertical pillar sections being mounted onto the base. Arrows indicate downward insertion. Parts A1, C1, and C2 are shown.
4. Install the Hanging Board
Attach the hanging board to the vertical pillars using part A1 and B1 screws (M8x20mm).
Diagram Description: Shows a horizontal board being attached to the upper section of the vertical pillars. Parts A1 and B1 are indicated.
5. Install the TV Mount
Attach the TV mounting brackets to the hanging board. Use F1/F2 screws with H1 washers, or G1/G2 screws with H1 and H2 washers, depending on your TV's VESA pattern. Secure the main mount to the board using fasteners (refer to diagram for specific parts, potentially E1 related components based on visual context, though E1 is listed as wheels).
Note: When installing the TV, use the height-raising pad (if provided) to prevent potential damage to your TV equipment from screws that may be too long when tightened.
Warning: Be sure to tighten all screws securely!
Diagram Description: Shows how to attach TV mounting arms to the main bracket, with options for different screw/washer combinations (F1/F2 with H1, G1/G2 with H1/H2). Also shows the main mount assembly being attached to the hanging board.
6. Install Camera Components
Attach any camera component mounting hardware (e.g., a shelf) to the top of the pillar structure using D1 (4X) and D2 (2X) screws.
Diagram Description: Shows a small shelf or bracket being attached to the top of the main pillar using screws D1 and D2.
Product Technical Specifications
The following dimensions apply to the Sylvox S40MCMA0 TV stand:
Overall Dimensions (Front View):
- Overall Width: 950mm
- Shelf Width: 255mm
- Shelf Height from Base: 160mm
- Base Width: 805mm
- Adjustable TV Height Range: 1080mm - 1330mm
- Maximum TV Screen Height (VESA area): 500mm
- Maximum TV Height Adjustment Range: 720mm
Overall Dimensions (Side View):
- Stand Depth: 120mm
- Overall Height Range: 1370mm - 1620mm (lower end) to 1440mm - 2035mm (upper end)
Diagram Description: Front, side, and top views of the TV stand with various dimensions indicated, including overall width, height, depth, shelf dimensions, and VESA mounting area height.
