Safety Instructions
To ensure safe operation and prolong the lifespan of your Anker SoundCore 2, please observe the following safety guidelines:
- Avoid dropping the device.
- Do not disassemble the device.
- Do not submerge the device in water.
- Avoid exposing the device to extreme temperatures.
- Use only original or certified cables for charging and connection.
- Do not use any corrosive cleaner or oil to clean the device.
- Do not use the device outdoors during thunderstorms.
Notice
ⓒ This product complies with the radio interference requirements of the European Community.
♼ This product is designed and manufactured with high quality materials and components, which can be recycled and reused. This symbol indicates that the product must not be discarded as household waste. It should be delivered to an appropriate collection facility for recycling. Proper disposal and recycling helps protect natural resources, human health, and the environment. For more information on disposal and recycling, contact your local municipality, disposal service, or the shop where you purchased this product.
FCC Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: (1) Reorient or relocate the receiving antenna. (2) Increase the separation between the equipment and receiver. (3) Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. (4) Consult the dealer or an experienced radio / TV technician for help.
RF Warning Statement
The device has been evaluated to meet general RF exposure requirements. The device can be used in portable exposure conditions without restriction.
Charging Your SoundCore
ⓗ The SoundCore 2 features a USB-C charging port. Connect a certified USB cable to charge the device.
| Indicator Light | Status |
|---|---|
| Flashing red | Low battery |
| Steady red | Charging |
| Steady white | Fully charged |
To preserve battery lifespan, fully charge the device at least once every 45 days.
Turn On / Off
ⓗ The power button is located on the top panel of the speaker.
| Action | Function | Indicator Light |
|---|---|---|
| Press | ON | Steady white |
| Press and hold for 1 second | OFF | Off |
Bluetooth Pairing
ⓗ The Bluetooth button is located on the top panel of the speaker.
| Action | Mode |
|---|---|
| Press | Enter pairing mode |
| Press and hold for 2 seconds | Un-pair connected device and re-enter pairing mode |
| Indicator Light | Status |
|---|---|
| Flashing blue | Pairing mode |
| Steady blue | Connected to a device |
When turned on, SoundCore will automatically connect to the last connected device if available. If not, SoundCore will enter pairing mode.
Connect via AUX
ⓗ The AUX port is located on the side of the speaker, protected by a rubber flap. Connect an AUX cable from your audio source to the SoundCore 2.
* SoundLine AUX cable sold separately.
To return to Bluetooth mode, remove the AUX cable from your SoundCore.
Controls
ⓗ The control buttons are located on the top panel of the speaker.
| Action | Music Playback | Call Management |
|---|---|---|
| ► x1 Press | Play / pause | Answer / End call |
| ► x2 Double press | Skip forward | |
| ► >1S Press and hold for 1 second | Reject call | |
| ► +/- Press | Volume up / down | |
| ► x1 Press | Put current call on hold and answer incoming call | |
| ► x1 Press | Switch between held call and active call | |
| ► >1S Press and hold for 1 second | Transfer a call between speaker and mobile phone | |
| ⓗ >1S Press and hold for 1 second | Activate Siri / other voice control software |
| Indicator Light | Call Status |
|---|---|
| Steady blue | On a call |
| Flashing blue | Incoming call |
Specifications
Specifications are subject to change without notice.
| Feature | Specification | Feature | Specification |
|---|---|---|---|
| Input | 5V = 2A | Charging time | 3 hours |
| Play time (varies by volume level and content) | Up to 24 hours | Driver (full range) | 1.5" x 2 |
| Audio output | 6 W x 2 | Frequency response | 70 Hz - 20 KHz |
| Impedance | 4 Ω | Bluetooth version | V4.2 |
| Range | 20 m / 66 ft | Waterproof rating | IPX 5 |
| Size | 168 x 47 x 56 mm / 6.6 x 1.9 x 2.2 in | Weight | 414 g / 14.6 oz |
Customer Service
For FAQs and more information, please visit: anker.com/support
18-month Limited Warranty
Anker provides an 18-month limited warranty for this product.
Lifetime Technical Support
Anker offers lifetime technical support for this product.
Contact Information
For customer service, you can reach Anker via email or phone:
- Email: support@anker.com
- Phone (US): 1-800-988-7973 (Mon-Fri 9:00-5:00 PST)
- Phone (DE): 069-9579-7960 (Mon-Fri 6:00-11:00)
- Phone (JP): 03-4455-7823 (Mon-Fri 9:00-17:00)
- Phone (UK): 01604-936200 (Mon-Fri 6:00-11:00)
- Phone (CN): 400-0550-036 (Mon-Fri 9:00-17:30)
Social Media
Follow Anker on social media for updates and support:
- Facebook: @Anker, @Anker Japan, @Anker Deutschland
- Twitter: @Anker Office, @Anker_JP
- Google+: @Anker
