Anker SoundCore Sport XL
Reference: SOUNDCORE SPORT XL
Model Code: 4413563
This document serves as a welcome guide and provides technical specifications for the Anker SoundCore Sport XL portable Bluetooth speaker.
What's Included
- Power button
- Volume buttons
- Play/Pause button
- Bluetooth pairing button
- Battery indicator
- Status indicator
- Microphone
- USB output
- 3.5mm Aux input
- Micro USB charging port
At a Glance
The speaker features the following controls and indicators:
- 1: Power button
- 2: Volume buttons
- 3: Play/Pause button
- 4: Bluetooth pairing button
- 5: Battery indicator
- 6: Status indicator
- 7: Microphone
- 8: USB output
- 9: 3.5mm Aux input
- 10: Micro USB charging port
Using Your SoundCore
Turn On/Off
Press and hold the power button for more than 1 second.
The SoundCore will automatically turn off after 30 minutes if no device is connected.
Pair with Your Device
Ensure Bluetooth is enabled on your device.
Pairing Indicator:
- Pairing Mode: The status indicator will flash blue rapidly ([rapidly flashing blue light]).
- Connected to a Device: The status indicator will be solid blue ([steady blue light]).
When turned on, SoundCore will automatically connect to the last connected device if available. If not, SoundCore will enter pairing mode.
To pair a different device, first disable Bluetooth on the connected device or press the [Bluetooth pairing button] to re-enter pairing mode. Then repeat the pairing steps.
Connection Problems? Remove SoundCore from your device's Bluetooth history, ensure it's less than 3 feet (approx. 90 cm) away, then try pairing again.
Connect via AUX
When using AUX mode, control audio playback via the connected device.
The status indicator will flash blue rapidly ([rapidly flashing blue light]) in AUX mode.
Charging
Check the Power Level
- 65%-100%
- 35%-65%
- 5%-35%
- <5%
Charge Your SoundCore
- Charging: The indicator light will flash white ([one flashing white light]).
- Fully Charged: The indicator light will be off ([light off]).
Ensure the protective flap is well sealed before exposing SoundCore to liquids. Do not charge near water.
Controls
Activate Voice Assistant
Press and hold the [Power button] for more than 2 seconds to activate Siri or other voice control software.
Un-pair Device
Press and hold the [Bluetooth pairing button] for more than 1 second to disconnect the current device and re-enter pairing mode.
Play / Pause
Press the [Play/Pause button] once.
Skip Forward
Press the [Play/Pause button] twice.
Volume Up / Down
Press the [Volume buttons] up or down.
Answer / End Call
Press the [Play/Pause button] once.
Reject Call
Press and hold the [Play/Pause button] for more than 1 second.
Put Current Call on Hold and Answer Incoming Call
Press the [Play/Pause button] once.
Switch Between Held Call and Active Call
Press and hold the [Play/Pause button] for more than 2 seconds.
Specifications
| Feature | Value |
|---|---|
| Waterproof Rating | IPX7 |
| Input | 5V / 2A |
| Audio Output | 8W x 2 |
| USB Output | 5V / 1A |
| Battery Capacity | 5200 mAh |
| Charging Time | 3-4 hours |
| Play Time (varies by volume level and content) | 15 hours |
| Size | 175 x 43 x 78 mm (6.9 x 1.7 x 3.1 in) |
| Weight | 600 g / 21.2 oz |
| Range | 20 m / 66 ft |
Attention
- Use original or certified cables.
- Do not disassemble the device.
- Avoid dropping the device.
- Avoid extreme temperatures.
FCC Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: (1) Reorient or relocate the receiving antenna. (2) Increase the separation between the equipment and receiver. (3) Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. (4) Consult the dealer or an experienced radio / TV technician for help.
RF Warning Statement
The device has been evaluated to meet general RF exposure requirements. The device can be used in portable exposure conditions without restriction.
Customer Service
For FAQs and more information, please visit: anker.com/support
Contact Information:
- US: 1-800-988-7973 | Mon-Fri 9:00-5:00 PST
- Japan: 03-4455-7823 | Mon-Fri 9:00-17:00
- Germany: 069-9579-7960 | Mon-Fri 6:00-11:00
- UK: 01604-936200 | Mon-Fri 6:00-11:00
- China: 400-0550-036 | Mon-Fri 9:00-17:30
Email: support@anker.com
Social Media: @Anker, @Anker Japan, @Anker Deutschland, @AnkerOfficial, @Anker_JP
Warranty: 18-month limited warranty
Support: Lifetime technical support
