Yaheetech 612450 Console Table

Important Information

Assembly Recommendation

We recommend 2 or more people to install this product. ?‍?‍?

Assembly Time

The expected assembly time is approximately 1 hour. ⏱️

Safety Warnings

This product is not intended for use by children. ??

Keep away from fire or other heat sources. ?

Recommended Equipment

We recommend wearing protective gloves during assembly. ?

Assembly Preparation

Please follow the instruction manuals and use a pad or protective cover to avoid damage during assembly. Ensure the floor is also protected.

Diagrams illustrate proper assembly preparation: one shows a red cross (❌) over a product on a bare floor, implying damage; the other shows a green checkmark (✔️) over a product on a protective pad or cover, indicating the correct procedure to avoid damage.

Parts List

Exploded View

Diagrams showing the overall assembly structure of the console table, illustrating how the main components (panels, shelves, side frames) fit together before detailed steps.

Assembly Instructions

Step 1

Attach part ① to part ⑩ using two Ⓕ screws and fifteen Ⓗ screws. Insert two Ⓙ components.

Step 2

Drawer Slide Preparation: To disassemble the slide rails, first pull out the slide rails. Then use a screwdriver to push down the plastic parts and draw tracks to the sides.

Diagrams show the process of separating the inner and outer parts of the drawer slides.

Step 3

Attach slide rail components to parts ② and ③ using Ⓑ screws.

Step 4

Attach slide rail components to parts ⑦ and ⑧ using Ⓑ and Ⓗ screws.

Step 5

Attach part ④ to part ③ using four Ⓐ screws.

Step 6

Insert part ⑤ (Drawer Front) into the assembled drawer structure.

Step 7

Attach parts ⑥ (Shelf Panels) to part ① (Top Panel) using four Ⓐ screws and eight Ⓖ screws.

Step 8

Attach parts ⑦, ⑧, ⑨, and ⑩ using Ⓖ screws.

Step 9

Continue assembling the drawer box structure using Ⓖ screws.

Step 10

Attach part ⑬ (Drawer Back Panel) to the drawer assembly using two Ⓔ screws.

Step 11

Attach part ⑪ (Drawer Bottom Panel) to the drawer assembly using two Ⓜ screws. This step is performed twice for both drawer bottom panels.

Step 12

Assemble the main frame of the console table. Attach side supports ⑫ to the top and bottom panels using Ⓐ and Ⓓ screws. During assembly, please first half-tighten all screws. After all screws are set, fully tighten them.

Step 13

Secure the structure further using Ⓒ and Ⓔ screws.

Step 14

Drawer Slide Operation: Diagrams show how to engage and disengage the drawer slides. No.1 and No.2 show extending the slide. No.3 shows the mechanism for releasing the slide.

Step 15

Wall Anchoring Guide: Use the guide below to identify your wall material and follow the appropriate steps for secure wall anchoring.

Diagrams illustrate the process of securing the furniture to different wall types.

Step 16

Anti-Tip Strap Installation: Install the anti-tip strap (Ⓛ) as shown in the diagram to secure the furniture to the wall.

Diagram shows a cable tie securing the strap to the furniture and the wall.

Drawer Operation

Removing the Drawer

To remove the drawer, pull up the left track lever (I-L) and push down the right track lever (I-R) simultaneously. Then, slide the drawer out as shown in the diagrams.

Diagrams detail the mechanism for removing the drawer by manipulating levers on the slide rails.

Wall Anchoring

For safety, it is highly recommended to anchor this furniture to the wall to prevent tipping. Follow the guide below based on your wall material.

Drywall or plaster with available wood stud:

Mark the attachment point with a pencil. Drill a pilot hole with a diameter matching the screw into the wood stud at the marked height. Secure the screw firmly.

Drywall without available wood stud:

Mark the attachment point with a pencil. Drill a hole with a diameter matching the plastic anchor through the wall at the marked height. Drive the plastic anchor into the hole, using a hammer if needed. Insert the screw into the plastic plug firmly. Do not over-tighten.

Masonry:

Mark the attachment point with a pencil. Drill a hole with a diameter and depth matching the plastic anchor through the wall at the marked height. Insert the plastic plug into the hole, using a hammer if needed. Insert the screw into the plastic plug firmly. Do not over-tighten.

If the screw cannot be secured to the wall, please keep the product away from children. ?

If your wall material is not listed here, or if you have any questions, consult your local hardware store.

Important Safety Warning

Do not allow children to climb on the furniture. ⚠️ This can lead to serious injury or death due to tipping.

Illustration shows a person climbing on the furniture with a prohibition symbol, indicating the danger of tipping.

Customer Satisfaction

If you are not entirely satisfied with your purchase, please feel free to contact us by following these steps:

1. Go to your Order list.
2. Find your order in the list.
3. Select 'Problem with order'.
4. Choose your topic from list displayed.
5. Select Contact seller.

You can also download the electronic Installation Manual from the Product guides and documents section of the advertising page.