Pipishell PIWFS02G Fireplace TV Stand Instruction Manual
Model: PIWFS02G
Important Safety Information
To assemble the product correctly, please read all instructions carefully before installation. If you have any questions or concerns, please contact Pipishell Technical Support at 1-800-556-9829 (US / CA), 44-808-196-3885 (UK) or Customer Service at support@pipishell.net.
This unit is not designed to be used with CRT TVs. Only use this stand with flat panel TVs and audio video equipment that meet the weight limits. Avoid the risk of personal injury or property damage. To ensure stability, place the TV in the center of the unit. The base of the TV must rest on the supporting surface of the unit without hanging over the edges.
To prevent the stand from tipping over, use the wall attachment device included with the product.
Weight Restrictions
If your products weigh more than the listed maximum weights, this TV stand is not compatible with your system.
- Top Shelf Weight Capacity: 200 lbs (90.7 kg) [max weight]
- Middle Shelf Weight Capacity: 20 lbs (9.1 kg) [max weight]
- Bottom Shelf Weight Capacity: 50 lbs (22.7 kg) [max weight]
Diagram shows the TV stand with weight capacities indicated for the top, middle, and bottom shelves.
Tools Needed (Not Included)
- Phillips Screwdriver [screwdriver]
- Rubber Mallet [rubber mallet]
- Electric Drill [electric drill]
- Hammer [hammer]
Illustrations of common tools required for assembly.
How the Assembly System Works
This section explains the core assembly mechanisms used in the product.
How to Install Wood Dowel
Insert the wood dowel [C] at least half-way. If necessary, lightly tap the wood dowel with a self-supplied rubber mallet. A diagram shows correct insertion (✔️) and incorrect insertion (❌).
Cam Lock System Operation
- Screw the cam bolt [A] into the threaded insert on the panel.
- Connect both panels together. Ensure the cam bolt [A] goes into the small pre-drilled hole on the end of the panel.
- Insert the cam lock [B] into the pre-drilled cam lock large hole on the panel. Make sure the open slot faces the head of the cam bolt [A].
- Rotate the cam lock [B] clockwise with a self-supplied Phillips screwdriver to lock the cam bolt [A] in place.
Diagrams illustrate the process of inserting wood dowels and operating the cam lock system, including correct and incorrect methods.
Contents and Parts
An exploded view diagram shows all components of the TV stand, numbered for reference. Assistance may be needed for some steps [warning].
Hardware:
- Cam Bolt [A] x 38
- Cam Lock [B] x 38
- Wood Dowel [C] x 36
- Door Stopper [D] x 2
- Screw [E] 3 x 12mm x 4
- Screw [F] 4 x 36mm x 4
- Screw [G] 3 x 12mm x 32
- Shelf Support [H] x 8
- Door Hinge [I] x 4
- Screw [J] 3.5 x 15mm x 24
- Bolt [K] 1/8" x 22mm x 4
- Door Handle [L] x 2
- Screw [M] x 2
Diagrams show the individual hardware pieces and their quantities.
STEP 1
Attach parts [D] and [E] to panels [5] and [6] using a Phillips screwdriver.
Diagrams show the placement of hardware [D] and [E] onto panels [5] and [6].
STEP 2
Insert cam bolts [A] and wood dowels [C] into panels [2], [5], and [6]. Ensure door stoppers face upward and outward, and the longer opening faces backward.
Diagrams show the insertion of cam bolts [A] and wood dowels [C] into specific panels. Notes indicate correct orientation for door stoppers and openings.
STEP 3
Attach panels [5] and [6] to panel [2] using cam locks [B] and a Phillips screwdriver. Ensure cam locks are rotated clockwise to secure.
Diagrams show panels [5] and [6] being connected to panel [2] using cam locks [B], with a close-up of the cam lock tightening process.
STEP 4
Insert wood dowels [C] into the designated holes on various panels.
Diagrams show the insertion of wood dowels [C] into multiple connection points.
STEP 5
Attach cam bolts [A] to parts [4] (x2) and [11] (x1) using a Phillips screwdriver.
Diagrams show cam bolts [A] being screwed into parts [4] and [11].
STEP 6
Align and attach parts [4] and [11] to the main structure. Ensure the raised edges of the door stiles are opposite each other.
Diagrams show the alignment and connection of parts [4] and [11] to the partially assembled unit, with a note on door stile orientation.
STEP 7
Attach cam locks [B] to panel [1] using a Phillips screwdriver.
Diagrams show cam locks [B] being inserted and tightened into panel [1].
STEP 8
Attach wood dowels [C] and screws [G] to parts [10] and [12]. Ensure the side with smaller holes on part [10] faces backward.
Diagrams illustrate the attachment of hardware [C] and [G] to parts [10] and [12], with a note on the orientation of part [10].
STEP 9
Attach cam bolts [A] to panel [7] and parts [13] and [15]. Then, connect these parts using cam locks [B] and wood dowels [C].
Diagrams show the process of attaching cam bolts [A] to panel [7] and parts [13], [15], followed by their connection using cam locks [B] and dowels [C].
STEP 10
Attach cam bolts [A] to panel [8] and parts [14] and [16]. Then, connect these parts using cam locks [B] and wood dowels [C].
Diagrams show the process of attaching cam bolts [A] to panel [8] and parts [14], [16], followed by their connection using cam locks [B] and dowels [C].
STEP 11
Attach cam locks [B] to panels [7] and [8] using a Phillips screwdriver.
Diagrams show cam locks [B] being inserted and tightened into panels [7] and [8].
STEP 12
Attach cam bolts [A] to panel [1] and wood dowels [C] to the side panels.
Diagrams illustrate the attachment of cam bolts [A] to the top panel [1] and wood dowels [C] to the side panels.
STEP 13
Align holes side-to-side and attach cam locks [B] to panel [1] using a Phillips screwdriver. Assistance may be needed [warning].
Diagrams show the alignment and connection of cam locks [B] to panel [1]. A side view is provided, and a warning icon indicates potential need for assistance.
STEP 14
Attach screws [F] to panel [1] using a Phillips screwdriver.
Diagrams show screws [F] being driven into panel [1].
STEP 15
Attach the back panel [17] to the top panel [1] using screws [G] and safety straps [M]. Do not fully tighten screws [G] until all are in correct position. Tighten all cam locks and screws to ensure the stand remains square.
Diagrams show the back panel [17] being attached to the top panel [1] with screws [G] and safety straps [M]. Close-ups show screw placement and cable management. A note emphasizes tightening all fasteners for squareness.
STEP 16
Insert four shelf supports [H] into the holes inside each side compartment. Rest the shelves [3] on the shelf supports [H].
Diagrams show shelf supports [H] being inserted into the side compartments and shelves [3] being placed onto them. Options for shelf placement are indicated.
STEP 17
Attach door hinges [I] and screws [J] to door panels [9]. Attach door handles [L] and screws [K] to the same panels.
Diagrams show the process of attaching hinges [I] and screws [J] to the doors [9], and handles [L] with screws [K].
STEP 18
Attach the doors with hinges [I] and screws [J] to the main unit. Do not fully tighten screws until Step 19 is finished. Note: There are only 2 locating holes for installing the hinge [I] on the panel. First, align the two vertical holes in the right of the hinge [I] with the 2 locating holes. Then screw the 2 screws [J] in the holes. Finally fasten the other 2 screws [J] in the panel.
Diagrams show the doors being attached to the unit. Close-ups detail hinge installation, emphasizing alignment with pre-drilled holes and the sequence of screwing.
STEP 19
Check and adjust door alignment using the three-way adjustable hinges. Turn set screws [S] clockwise to narrow gaps and counterclockwise to enlarge gaps between doors and side panels.
If the stand is not stable on the flat floor, adjust the levelers on the two front legs and two center legs until the stand is stable.
Diagrams illustrate the three adjustment points for the hinges (up/down, forward/backward, left/right) by turning set screws [S]. A note about adjusting leg levelers for stability is included.
STEP 20
Secure the TV stand to the wall using the included safety straps [M]. Follow instructions for mounting into wood studs or solid concrete/block/brick walls, using appropriate drill bit sizes and screw lengths.
Diagrams show two methods for wall mounting: one for wood studs using 1" (25mm) screws and Ø5/64" (2mm) drill bits, and another for solid concrete/block/brick walls using 1 3/16" (30mm) screws and Ø1/4" (6mm) drill bits. The straps [M] are shown attached to the unit and the wall.
