Important Safety Information
Please carefully read all instructions before attempting installation. If you do not understand the instructions or have any questions or concerns, please contact Pipishell technical support at 1-800-556-9829 (US/CA) / 44-808-196-3885 (UK) or customer service at support@pipishell.net.
CAUTION: Avoid potential injuries and property damage!
- DO NOT use this product for any purpose that is NOT explicitly specified in this manual. Pipishell is NOT liable for damage or injury caused by improper mounting, incorrect assembly, or inappropriate use.
WARNING: Choking Hazard
This product contains small items that may pose a choking hazard. Before starting assembly, verify all parts are included and undamaged. DO NOT use damaged or defective parts. If you require replacement parts, please contact Pipishell technical support at 1-800-556-9829 (US/CA) / 44-808-196-3885 (UK) or customer service at support@pipishell.net.
Weight Restrictions
Verify that the items you intend to store do not exceed the listed weight capacity:
| Location | Maximum Capacity |
|---|---|
| Top Shelf | 150 lbs (68kg) |
| Middle Shelf | 30 lbs (13.6kg) |
| Drawer | 11 lbs (5kg) |
| Bottom Shelf | 60 lbs (27.2kg) |
Visual representation shows the TV console with 'MAX' labels indicating weight limits for the top shelf, middle shelf, drawers, and bottom shelf.
Tools Needed (Not Included)
- Phillips Screwdriver
Parts List
| Part Ref | Description | Quantity |
|---|---|---|
| [1] | Left Middle Frame | 1 |
| [2] | Right Middle Frame | 1 |
| [3] | Mesh Panel | 1 |
| [4] | Bottom Panel | 1 |
| [5] | Leg | 4 |
| [6] | Bottom Frame | 1 |
| [7] | Top Support Bar | 2 |
| [8] | Left End Frame | 1 |
| [9] | Right End Frame | 4 |
| [10] | Top Panel | 1 |
| [11] | Fabric Drawer | 4 |
| [12] | Drawer Bottom | 4 |
| [A] | M6 x 30mm Bolt | 12 |
| [B] | M3.5 x 12mm Screw | 4 |
| [C] | M6 x 12mm Bolt | 8 |
| [D] | Adjustable Foot | 4 |
| [E] | M6 x 23mm Bolt | 14 |
| [F] | M4 x 12mm Screw | 8 |
| [G] | Handle | 4 |
| [H] | 5/32" (4mm) Allen Key | 1 |
Assembly Instructions
IMPORTANT INSTALLATION TIP: Align and loosely thread all bolts into the corresponding holes before fully tightening each bolt one by one.
Step 1: Assemble Main Frame Base
Attach the [1] Left Middle Frame and [2] Right Middle Frame to the [3] Mesh Panel. Use four [A] M6 x 30mm Bolts and the [H] Allen Key. Ensure the recessed side of the mesh panel faces inwards. The support bars on frames [1] and [2] must face outwards with the lip toward the back.
Diagram shows frames [1] and [2] connecting to the mesh panel [3] with bolts [A] and allen key [H]. A close-up highlights the orientation of the mesh panel and the lip on the support bars.
Step 2: Attach Bottom Panel and Feet
Connect the [4] Bottom Panel to the [6] Bottom Frame using four [B] M3.5 x 12mm Screws. Attach the four [5] Legs to the corners of the [4] Bottom Panel using eight [C] M6 x 12mm Bolts and the [H] Allen Key. Screw in the four [D] Adjustable Feet into the bottom of each leg. Ensure the feet face outwards.
Diagram shows the bottom frame [6] and bottom panel [4] being assembled with screws [B]. Legs [5] are attached to the bottom panel with bolts [C] and allen key [H]. Adjustable feet [D] are screwed into the legs. The 'TOP SIDE' note indicates the correct orientation.
Step 3: Attach Side Panels
Attach the [8] Left End Frame and [9] Right End Frame to the assembly from Step 2. Use eight [E] M6 x 23mm Bolts and the [H] Allen Key. The support bars on frames [8] and [9] must face inwards with the lip toward the back.
Diagram shows the left and right end frames [8] and [9] being attached to the base structure using bolts [E] and allen key [H]. A close-up shows the orientation of the support bars.
Step 4: Install Top Support Bars
Attach the two [7] Top Support Bars to the top of the side frames. Use four [E] M6 x 23mm Bolts and the [H] Allen Key for each bar. Ensure the large holes on the support bars [7] face outwards.
Diagram shows the two top support bars [7] being attached to the top of the side frames using bolts [E] and allen key [H]. A note specifies that the large holes on the support bars must face outwards.
Step 5: Attach Side Panels (Continued)
Attach the [8] Left End Frame and [9] Right End Frame to the main structure. Use eight [A] M6 x 30mm Bolts and the [H] Allen Key. The support bars on frames [8] and [9] must face in with the lip toward the back.
Diagram shows the left end frame [8] and right end frame [9] being attached to the structure. Bolts [A] and allen key [H] are used. A note indicates the orientation of the support bars on these frames.
Step 6: Attach Top Panel
Place the [10] Top Panel onto the assembled frame. Secure it using six [E] M6 x 23mm Bolts and the [H] Allen Key.
Diagram shows the top panel [10] being placed on the frame and secured with bolts [E] and allen key [H]. A reminder is given to fully tighten all bolts and screws after this step.
Step 7: Assemble and Install Drawers
Assemble the four drawers. For each drawer, attach the sides of the [11] Fabric Drawer to the [12] Drawer Bottom using eight [F] M4 x 12mm Screws and a Phillips Screwdriver. Attach the [G] Handles to the front of each drawer using the remaining [F] M4 x 12mm Screws. Slide the assembled drawers into the console.
Diagram shows the assembly of a fabric drawer [11] with a drawer bottom [12] using screws [F]. Handles [G] are attached. The completed drawers are shown being inserted into the console. A note advises to adjust the feet if the unit is not level.
