Pipishell Installation Instructions

Important Safety Information

• Check package contents against Supplied Parts and Hardware Lists to assure that all components were received undamaged. Do not use damaged or defective parts. If you require replacement parts, contact customer service at supportus@pipishell.net.
• Not all parts and hardware included will be used.
• Carefully read all instructions before attempting installation. If you do not understand the instructions or have any concerns or questions, please contact customer service at supportus@pipishell.net.
• This product may contain moving parts. Use with caution.
• Do not use this product for any purpose or in any configuration not explicitly specified in this instruction. Pipishell disclaims any liability for injury or damage arising from incorrect assembly, incorrect mounting, or incorrect use of this product.
• DO NOT INSTALL INTO DRYWALL ALONE.

Tools Needed (Not Included)

• Stud finder
• Tape measure
• Pencil
• Drill
• Hammer
• 7/32 in.(5.5mm) Wood drill
• 25/64 in.(10mm) Concrete drill
• 25/64in.(10mm) socket wrench
• 1/2in.(13mm) socket wrench
• Screw driver

Supplied Parts

• [01] Wall Plate - 1 PC
• [02] TV Brackets - 2 PCS

Supplied Hardware

Hardware for Attaching Wall Plate to Wall

• A1: Lag Bolts M8X65 (x4)
• A2: Washers M8 (x4)
• A3: Wall Anchor (x4) - ⚠️ CAUTION: These anchors are for concrete or brick walls ONLY. DO NOT use them in drywall or wood studs.

Hardware for Attaching TV Bracket to TV

• B: Washers M6 (x4)
• C1: Spacers L5mm (x8)
• C2: Spacers L10mm (x8)
• D1: Philips Screws M6 x 15mm (x4)
• D2: Philips Screws M6 x 30mm (x4)
• E1: Philips Screws M8 x 15mm (x4)
• E2: Philips Screws M8 x 45mm (x4)
• F: Philips Screws M4 x 30mm (x4)

Step 1: Measure VESA and Check TV Screws

Measure the distance between the holes located at the back of your TV. These measures may form the shape of a square or a rectangle. Check that these measurements are within the VESA range for this wall mount. VESA is an international standard established by TV manufacturers used to determine if LCD/LED TVs are compatible with wall mounts.

VESA Dimensions:

• 75 mm ≈ 2 7/8 in
• 100 mm ≈ 4 in
• 200 mm ≈ 7 7/8 in
• 300 mm ≈ 11 3/4 in
• 400 mm ≈ 15 3/4 in

When attaching brackets to the flat screen, be careful not to overtighten screws and ensure that screws do not bottom out in the mounting holes.

Check TV Screws: Hand thread screws into the threaded inserts on the back of your TV to determine which screw diameter (M4, M6, or M8) to use.

Screw Fit Examples:

• Too Short ❌
• Too Long ❌
• Correct ✔️
• Correct ✔️

Step 2: Attach the TV Brackets to the TV

For FLAT BACK TV (UNIVERSAL MONITOR PLATE)

Attach the TV brackets [02] using the appropriate screws (D1 or E1) and washers (B) as shown in the diagram. Ensure the brackets are vertically centered and level.

For ROUND BACK TV (UNIVERSAL MONITOR PLATE)

First, make sure the diameter of the bolt (D1-F) fits your TV. Then, use the washer (B) and spacer (C1 or C2) as needed. Ensure the monitor brackets [02] are vertically centered and level with each other.

Step 3: Attach Wall Plate to Wall

For wood stud installation, follow STEP 3A. For concrete installation, follow STEP 3B.

STEP 3A: Wood Stud Option

WARNING: Avoid potential personal injury or property damage! DO NOT overtighten the lag bolts [A1]. Tighten the lag bolts [A1] only until the washers [A2] are pulled firmly against the wall plate [01].

WARNING: Ensure the wall plate is securely fastened to the wall before continuing on to the next step.

WARNING:

• Drywall covering the wall must not exceed 5/8 in. (16 mm).
• Nominal wood stud size: common 2 x 4 in. (51 x 102 mm) minimum 1 1/2 x 3 1/2 in. (38 x 89 mm).
• Stud center must be verified.

3A-1: Locate Stud

Use a stud finder (not included) to locate wood stud. Mark the edge and center locations.

3A-2: Mark Center

Ensure marking is at the center of the stud.

3A-3: Drill Pilot Holes

Drill 4 pilot holes using a 7/32 in. (5.5mm) Wood Drill bit. Make sure the depth is not less than 65mm (approx. 2 1/2 in.).

3A-4: Mount Wall Plate

Mount the wall plate [01] using 4 sets of M8X65 lag bolts [A1] and washers [A2] with a 1/2 in. socket wrench (not included).

STEP 3B: Solid Concrete or Concrete Block Option

WARNING: Avoid potential personal injury or property damage! DO NOT overtighten the lag bolts [A1]. Tighten the lag bolts [A1] only until the washers [A2] are pulled firmly against the wall plate [01].

WARNING: Ensure the wall plate is securely fastened to the wall before continuing on to the next step.

WARNING:

• Mount the wall plate [01] directly onto the concrete surface.
• Minimum solid concrete thickness: 203 mm (8 in.).
• Minimum concrete block size: 203 x 203 x 406 mm (8 x 8 x 16 in.).
• Drywall covering the wall must not exceed 5/8 in. (16 mm).

3B-1: Position and Mark

Position the wall plate at your desired height, level the wall plate and mark the 4 pilot hole locations.

3B-2: Drill Pilot Holes

Drill 4 pilot holes using a 25/64 in.(10mm) Concrete Drill bit. Make sure the depth is not less than 2 3/4 in. (70mm).

3B-3: Insert Anchors

Use the hammer to knock anchors [A3] into the wall.

3B-4: Mount Wall Plate

Install wall plate using lag bolts [A1], washers [A2] and anchors [A3]. Be sure the anchors [A3] are seated flush with the concrete surface. Tighten the lag bolts [A1] only until the washers [A2] are pulled firmly against the wall plate [01]. DO NOT over-tighten the lag bolts [A1].

STEP 4: Level Adjustment

If needed, the TV can be leveled using the adjustment screws on the brackets.

STEP 5: Hang the TV onto the Wall Plate

Carefully hang the TV, with the attached brackets, onto the wall plate. Ensure it is securely locked in place. Tilt adjustment and locking mechanisms are available.