TROFAST Storage System Assembly Instructions
This guide provides step-by-step instructions for assembling the IKEA TROFAST storage system.
Important Safety Information
Warning: Assembly should be carried out by a qualified person. Incorrect assembly can lead to the furniture toppling over, causing injury or damage. As wall materials vary, screws for fixing to the wall are not included. For advice on suitable screw systems, contact your local specialised dealer.
Tools Required: Screwdriver ?, Screws ?, Spirit level ?
Assembly Tips:
- Ensure correct assembly procedures are followed.
- Assemble on a soft surface (e.g., a rug) to prevent damage to the furniture.
- If you have questions or need assistance, contact IKEA.
Parts List
Please check that you have all the parts listed below before starting assembly.
- 16x Spring (Part ID: 112219)
- 16x Dowel (Part ID: 101350)
- 1x Allen Key (Part ID: 100006)
- 2x Wall Bracket (Part ID: 103693)
- 2x Bracket Cover (Part IDs: 115754, 118225)
- 2x Support Piece (Part ID: 115753)
- 12x Screw (Part IDs: 121008, 129893)
- 16x Screw (Part IDs: 100229, 100232)
Assembly Steps
-
Step 1: Attach runners to the side panels. Use 8x screws (Part IDs: 121008, 129893) for the first set of panels.
Diagram Description: Shows attaching horizontal runners to vertical side panels using screws. Ensure correct orientation of runners.
-
Step 2: Attach runners to the remaining side panels. Use 4x screws (Part IDs: 121008, 129893).
Diagram Description: Similar to Step 1, attaching runners to the other side panels.
-
Step 3: Attach support pieces. Use 2x screws (Part ID: 100349) and 2x dowels (Part ID: 115753) per support piece.
Diagram Description: Shows attaching the vertical support pieces to the side panels using screws and dowels.
-
Step 4: Connect the base panel to the side panels. Insert dowels (Part ID: 101350) and secure with screws.
Diagram Description: Shows the base panel being connected to the assembled side panels using dowels and screws.
-
Step 5: Attach the top panel. Use 4x screws (Part IDs: 100229, 100232).
Diagram Description: Shows the top panel being attached to the assembled structure using screws.
-
Step 6: Insert back panels. Use dowels (Part ID: 101350).
Diagram Description: Shows back panels being inserted, likely into grooves or slots, using dowels for alignment.
-
Step 7: Attach wall mounting brackets to the unit. Use 4x screws (Part IDs: 100229, 100232) and 4x springs (Part ID: 112219) for the brackets.
Diagram Description: Shows attaching the metal wall brackets to the top rear of the unit using screws and springs.
-
Step 8: Insert dowels into the unit. Use 8x dowels (Part ID: 101350).
Diagram Description: Shows inserting dowels into pre-drilled holes on the unit, likely for final assembly or stability.
-
Step 9: Attach the end panels. Arrows indicate the direction of attachment.
Diagram Description: Shows the side/end panels being attached to the main structure.
-
Step 10: Secure the unit to the wall. Use 8x screws (Part IDs: 100229, 100232) through the wall brackets.
Diagram Description: Shows the assembled unit being mounted to the wall using screws that pass through the attached brackets.
Installation Clearance
Ensure a minimum clearance of 55 cm (21 3/4") is maintained around the unit during installation, as indicated in the diagram.
Diagram Description: Shows the assembled unit with a measurement indicating a minimum clearance of 55 cm (21 3/4").
Final Wall Mounting
Step 11: Two people are shown mounting the unit to the wall. Use a spirit level to ensure it is straight.
Diagram Description: Two people are shown lifting and positioning the assembled unit against the wall. One person is using a spirit level to check alignment.
Step 12: Close-up of attaching the wall bracket to the wall using screws.
Diagram Description: A close-up view of a wall bracket being secured to the wall with screws.
Step 13: Secure the unit to the wall brackets.
Diagram Description: Shows the unit being slid or clicked onto the wall-mounted brackets, securing it in place.
