MakeID Label Printer-P1 Quick Start Guide

一、包装清单 ? Packaging List

This section details the items included in the printer's packaging.

• Printer: 1 * Printer-P1

  Description: A diagram shows a cardboard box being opened, revealing a compact label printer inside.

• USB Cable: 1 * USB Cable

  Description: A diagram shows a USB-A to USB-B cable.

• Power Adapter: 1 * Power Adapter

  Description: A diagram shows a power adapter with a cable and a wall plug.

• User Manual: 1 * User Manual

  Description: A diagram shows a booklet labeled "User Manual".

• Quick-Start Guide: 1 * Quick-Start Guide

  Description: A diagram shows a small card labeled "Quick-Start Guide".

• Type-C Adapter: 1 * Type-C Adapter

  Description: A diagram shows a USB Type-C adapter.

• Label Roll: 1 * Label Roll

  Description: A diagram shows a roll of thermal label paper.

Software Download Address: https://www.makeid.com/jj/download/pceditor/

Please visit the link above to download the software.

二、按键功能 ?️ Printer Button

This section describes the buttons and indicators on the printer.

三、如何开机 ▶️ Power On the Printer

Follow these steps to power on your label printer.

1. Step 1: Connect the power cable to the power adapter. Then, plug the adapter into the printer's power port, and the other end into an electrical socket.

   Diagram Description: Shows connecting the USB cable to the power adapter, then to the printer's power port, and finally to a wall socket.

2. Step 2: Plug one end of the USB cable into the printer's USB port and the other end into your computer. If you are using a Mac, you may need the included Type-C adapter.

   Diagram Description: Shows connecting the USB cable to the printer and a computer. An arrow indicates the potential use of a Type-C adapter for Mac computers.

3. Step 3: Power on the printer using the power button.

四、如何安装标签 ?️ Installation of Label Roll

⚠️ CAUTION: Only genuine MakeID labels can be used in this printer. Genuine MakeID labels are detected by a label recognition function, allowing the MakeID PC editor software to receive label information, such as the type of label being used.

1. Step 1: Take out the label roll.

   Diagram Description: Shows a label roll being taken out of its packaging.

2. Step 2: Open the printer's top cover.

   Diagram Description: Shows the printer's top cover being opened.

3. Step 3: Push aside the label clippers and put in the label roll with the printable side facing up.

   Diagram Description: Shows a label roll being inserted into the printer, with the printable side oriented upwards.

4. Step 4: To hold the label roll in place, ensure the clipper tabs are threaded through the center of the roll.

   Diagram Description: Shows a close-up of the label roll secured by the clipper tabs.

5. Step 5: Pull the label out to the exit slot.

   Diagram Description: Shows the label paper being pulled out of the printer's exit slot.

6. Step 6: Shut the cover.

   Diagram Description: Shows the printer's top cover being closed.

⚠️ CAUTION:

• The printable side should face up.
• Pull the label out to the exit slot.
• Ensure the clipper tabs are threaded through the center of the roll to hold it in place.

五、如何使用打印软件 ? Use of Printing Software

1. Step 1: Please ensure that the previous steps (label installation) are completed correctly in accordance with the user manual.

2. Step 2: Visit https://www.makeid.com to download and install the latest version of the MakeID label printer software, which is exclusively designed for desktop PCs.

   Description: The page shows a screenshot of the MakeID website's download section, listing software and driver downloads for various printer models.

3. Step 3: Double-click the software installation package and follow the on-screen installation guide to complete the installation of the desktop printing software.

   Diagram Description: Shows file explorer windows with folders like 'driver', 'service', 'tools', 'install', and 'uninstall', indicating the software installation structure.

4. Step 4: Edit your text using the MakeID software.

   Diagram Description: A screenshot of the MakeID label editing software interface, showing tools for adding text, QR codes, barcodes, images, and adjusting properties. A label design with text and QR codes is visible.

5. Step 5: Print out the label.

   Diagram Description: A screenshot of the MakeID software's print preview and print dialog, showing options for selecting the printer, page setup, and number of copies.

六、打印机参数 ?️ Printer Parameter

七、故障指示 ❗ Malfunction Indication

⚠️ Precautions

• Do not disassemble the printer or power adapter to avoid possible electrocution, mechanical injury, or damage to printer components.
• If the printer or power adapter shows abnormalities like smoke or unusual odor, unplug it immediately to avoid burns.
• Do not touch the print head immediately after continuous printing or when the printer just finished printing, as it is still hot.
• Do not use poor-quality labels (non-genuine labels) as this may damage the print head and shorten its life. Damages caused by poor-quality labels are not covered by warranty.
• Do not touch the print head or electronic components to prevent static electricity damage.
• Unplug the printer if it will not be used for a long period.
• Do not press or hit the printer, as this may cause damage or malfunctions.
• If the printer is soaked in water or damaged, stop using it and have it repaired immediately.
• It is recommended to use the printer within a temperature range of 5°C ~ 35°C and humidity of 20% ~ 90% for optimal performance and to prevent print head damage.
• If there is a large temperature difference between indoors and outdoors, allow the printer to acclimate to room temperature before use to prevent condensation.
• For optimal print quality and print head longevity, it is recommended not to print more than 2 meters continuously in one go, and a total daily printing length not exceeding 150 meters.
• Do not scratch the print head with hard objects. Damages from improper maintenance are not covered by warranty.

❗ WARNING: The print head is a fragile component. Pay attention to the following to avoid corrosion:

• Do not touch the print head surface with your hands.
• Do not use thermal labels containing sodium (Na), potassium (K), or chloride (Cl) ions.
• Avoid contact between the print head and any liquids or wet objects.
• Clean the print head only with anhydrous alcohol.
• Do not pull the label while the printer is working.
• Do not use non-MakeID official labels.

安全须知 ? Safety Instruction

1. 安全警告 ⚠️ Safety Warning

Please read the following precautions with attention before using the printer.

• WARNING: Do not touch the print head or its surrounding components during or just after printing, as the print head is a heat-generating component.
• WARNING: Do not touch the print head surface or the connection plug-ins to avoid causing damage to the print head due to static electricity.

2. 注意事项 ? Precaution

• Install the printer on a flat, stable surface.
• Ensure adequate space around the printer for operation and maintenance. Keep it away from water sources.
• Do not use or store the printer in high-temperature, high-humidity, or heavily polluted areas. Avoid direct sunlight, bright lights, and heat sources. Do not place it in areas subject to vibration or shock.
• Avoid condensation on the printer surface due to humid air. If condensation forms, do not power on the printer until it has disappeared.
• Connect the printer's power adapter to a properly grounded outlet. Avoid using the same outlet as large motors or devices that cause voltage fluctuations.
• Avoid water or conductive materials (e.g., metals) from entering the printer. If this occurs, power off the printer immediately.
• The printer must not be operated without labels; otherwise, the roller and print head will be seriously damaged.
• Ensure the printer is powered off when connecting or disconnecting any ports to avoid damage to control circuits.
• Do not self-disassemble the printer for maintenance or repair.
• Keep this manual for your reference.

使用电源适配器注意事项 ⚡ Precaution when Using Power Adapter

• Do not use damaged or worn-out power cables, as they might cause electrocution or fires.
• Do not touch the power adapter, plug, or output terminal with wet hands to prevent electrocution.
• Do not excessively bend or forcefully pull the power cable, nor place heavy objects on it, as this may damage the cable and cause electrocution or fires.
• When unplugging, hold the plug part, not the cable, to avoid damage and potential electrocution or fires.
• Please use the original MakeID power adapter. Using a non-original adapter may result in printer burnout or operator injury, which is not covered by the warranty.
• Keep the power adapter away from children to avoid danger.
• Always power off the printer before maintenance or repair to avoid danger.

保修说明 ? Warranty

MakeID provides a one-year warranty.

You are entitled to a one-year warranty from the date of purchase for quality and function issues. MakeID will provide free repair services.

1. For repairs or replacements within the warranty period, provide your order number, contact information, and delivery details (name, phone number, full address).
2. Products returned to MakeID must be fully packaged. MakeID is not responsible for loss or damage during shipping by the customer.
3. Product must be operated strictly according to the provided instructions. MakeID is not responsible for issues caused by accidents, misuse, modification, or negligence.
4. The MakeID label printer is designed exclusively for MakeID labels. Malfunctions or damages caused by using other manufacturers' labels are not covered by the warranty.
5. This warranty does not affect your legal rights as a consumer.

Warranty Card

封底 ? Back Cover

MakeID

Chongqing Jingranyouxu Technology Co., Ltd

Web: WWW.MakeID.COM

FCC CAUTION:

§ 15.19 Labeling requirements.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

§ 15.21 Information to user.

Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

§ 15.105 Information to the user.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.