WEDDING ARCH BACKDROP STAND

USER MANUAL

Thank you for choosing this product. This manual provides information to help you achieve the best possible results. Please read all instructions carefully before use.

Note: Drawings in this manual are for illustration purposes only and may differ in some details from the actual product.

Attention: Read all safety warnings and instructions. This product is intended for use as a wedding arch backdrop stand and is not a toy. Keep children away from it and ensure it is placed in a position where children cannot climb to avoid injury from falling.

USAGE SAFETY

1. Before installation, verify all parts are present in the packaging box. Contact your seller if any parts are missing.
2. Select a clean assembly area free of debris that could cause tripping hazards.
3. Review the assembly instructions before proceeding.
4. After assembly, thoroughly inspect the stand to ensure all nuts and bolts are securely tightened.
5. This product is not a climbing frame or hanging tool and should only be used as a wedding arch backdrop stand.
6. Parts not marked with specific dimensions (e.g., "x FT") are general parts that can be installed according to the instructions.

SAVE THESE INSTRUCTIONS

SPECIFICATIONS

PARTS LIST

8ft Stand

7.2ft Stand

6.6ft Stand

PRODUCT ASSEMBLY

8ft Stand Assembly

1. Step 1: Assemble Part “8FT F”, “8FT G” & “8FT H” using hardware "I" to form the arch shape.
2. Step 2: Assemble Part "B" (base support tubes) to the bottom of the arch segments using hardware "I".
3. Step 3: Assemble Part "A" (vertical support tubes) to the base structure using hardware "I".
4. Step 4: Assemble the remaining arch segments (“8FT C”, “8FT D” & “8FT E”) using hardware "I". Secure these segments to the main frame using part "J". The position of the assembled part "I" on the component can be adjusted before locking with part "J".

7.2ft Stand Assembly

1. Step 1: Assemble Part “7.2FT F”, “7.2FT G” & “7.2FT L” using hardware "I" to form the arch shape.
2. Step 2: Assemble Part "B" (base support tubes) to the bottom of the arch segments using hardware "I".
3. Step 3: Assemble Part "A" (vertical support tubes) to the base structure using hardware "I".
4. Step 4: Assemble the remaining arch segments (“7.2FT C”, “7.2FT D” & “7.2FT E”) using hardware "I". Secure these segments to the main frame using part "J". The position of the assembled part "I" on the component can be adjusted before locking with part "J".

6.6ft Stand Assembly

1. Step 1: Assemble Part “6.6FT F”, “6.6FT G” & “6.6FT H” using hardware "I" to form the arch shape.
2. Step 2: Assemble Part "B" (base support tubes) to the bottom of the arch segments using hardware "I".
3. Step 3: Assemble Part "A" (vertical support tubes) to the base structure using hardware "I".
4. Step 4: Assemble the remaining arch segments (“6.6FT C”, “6.6FT D” & “6.6FT E”) using hardware "I". Secure these segments to the main frame using part "J". The position of the assembled part "I" on the component can be adjusted before locking with part "J".

ADDITIONAL INFORMATION

If the arch backdrop stand is installed on soft ground, such as grass, it can be reinforced with part "M" (ground stake).

MANUFACTURER AND IMPORTER INFORMATION

Manufacturer: Shanghaimuxinmuyeyouxiangongsi

Address: Shuangchenglu 803nong11hao1602A-1609shi, baoshanqu, shanghai 200000 CN.

Imported to AUS: SIHAO PTY LTD. 1 ROKEVA STREET, EASTWOOD NSW 2122, Australia

Imported to USA: Sanven Technology Ltd. Suite 250, 9166 Anaheim Place, Rancho Cucamonga, CA 91730

European Representative: E-CrossStu GmbH, Mainzer Landstr.69, 60329 Frankfurt am Main.

UK Representative: YH CONSULTING LIMITED. C/O YH Consulting Limited Office 147, Centurion House, London Road, Staines-upon-Thames, Surrey, TW18 4AX