VEVOR Pipe Stand: Operating Instructions and Parts Manual
Brand: VEVOR
Introduction
Please read and save these instructions. Read through this owner's manual carefully before using product. Protect yourself and others by observing all safety information, warnings, and cautions. Failure to comply with instructions could result in personal injury and/or damage to product or property. Please retain instructions for future reference.
Description
Designed to support pipes for a variety of uses. Do not exceed the maximum capacity of the product.
Inspection and Maintenance
Carefully inspect the stand prior to each use for proper assembly (such as the hand screw), wear, damage, or other issues that may affect safe usage. If any problems are found, discontinue use until the stand is repaired. Keep the stand clean and all moving parts lightly lubricated to aid in operation.
General Safety Information
WARNING: Read the warnings and instructions for all equipment being used before operating this tool to reduce the risk of serious personal injury.
WARNING: Failure to properly support the pipe may result in tipping of the stand, dropping of the pipe, or serious injuries.
WARNING: Use the appropriate safety equipment for the intended job such as eye protection, hearing protection, foot protection, dust masks, face shields, etc., to reduce the risk of injuries.
Installation and Operation
- Make sure that all equipment is inspected and set up accordingly.
- Make sure that the ground below the pipe stand is clear, stable, and level.
- The legs of the pipe stand should be fully open and the feet placed squarely on the floor.
- If the stand is equipped with rollers, ensure the rollers are properly adjusted for the pipe size.
- Fasteners on the pipe stand should be evaluated and ensure that they are secured.
- To adjust the height: grip the head assembly, loosen the hand screw, and raise the lock ring to disengage the elevator tube. Move the head assembly to the desired height. Next, lower the lock ring until it engages the elevator tube, and securely tighten the hand screw. Do not raise the elevator tube past the hand screw or past the unit specifications. The jack screw can be used for fine adjustments to height. Do so by holding the head of the assembly station and carefully turning the jack screw handle to the desired height. Do not force the jack screw handle, as it may cause the screw to come loose from the stand.
- Position the stand(s) to properly support the pipe. The pipe should be supported in at least two places at all times. The number and placement of stands depends on the size, length, and weight of the pipe.
- Carefully place the pipe on the stands. Make sure the pipe is properly centered on the stands to reduce the risk of tipping. Always stay clear of the supported load.
Attention Points
[Observation Hole Check]: Make sure you can always see the screw through the observation holes. ?
[Height Limit]: Do not exceed the maximum line of the inner tube. ⚠️
[Security]: Tighten the safety nut for more security. ?
Diagram Description: The document includes a visual sequence illustrating height adjustment steps. It shows gripping the head assembly, loosening a screw, raising a lock ring, moving the head, lowering the lock ring, and tightening the screw. Another visual shows using a jack screw handle for fine adjustments.
Product Models and Specifications
The following table lists various VEVOR pipe stand models with their specifications:
| Part Number | Pipe Capacity (In.) | Max Weight Capacity | Overall Height (In.) |
|---|---|---|---|
| 1107 | 1/8 To 12 | 2500 lbs | 28" To 52" |
| 1107A2-BALL | 1/8 To 12 | 1300lbs | 28" To 52" |
| 1107A4-BALL | 1/8 To 12 | 1500lbs | 28" To 52" |
| 1107B | 1/8 To 12 | 2500lbs | 24" To 42" |
| 1107B2-BALL | 1/8 To 12 | 1300lbs | 24" To 42" |
| 1107B4-BALL | 1/8 To 12 | 1500lbs | 24" To 42" |
| 1107C | 1/8 To 12 | 2500lbs | 20" To 37" |
| 1107C2-BALL | 1/8 To 12 | 1300lbs | 20" To 37" |
| 1107C4-BALL | 1/8 To 12 | 1500lbs | 20" To 37" |
| 1107S | 1/8 To 12 | 2500lbs | 28" To 52" |
| 1107S2-BALL | 1/8 To 12 | 1300lbs | 28" To 52" |
| 1107S4-BALL | 1/8 To 12 | 1500lbs | 28" To 52" |
| 1109 | 1/8 To 12 | 2500lbs | 32" To 55" |
| 1106 | 1/8 To 24 | 3000lbs | 28" To 52" |
| 1108 | 300lbs | 32" To 45" |
Visual Description: The document displays images of various pipe stand models including V-Head Pipe Stands, V-Head Pipe Jack Stands with Casters, V-Roller Head Pipe Stands, and a Multi-Function Jaw Stand, each associated with their part numbers.
