VEVOR TOUGH TOOLS, HALF PRICE

Technical Support and E-Warranty Certificate

www.vevor.com/support

WEDDING ARCH BACKDROP STAND

USER MANUAL

VEVOR is committed to providing tools at competitive prices. Expressions like "Save Half" or "Half Price" are estimates of potential savings compared to major top brands and may not apply to all tool categories. Please verify savings when placing an order.

WEDDING ARCH BACKDROP STAND

Model: TFHQGM87266FT

NEED HELP? CONTACT US!

For product questions or technical support, please visit www.vevor.com/support.

This is the original instruction manual. Please read all instructions carefully before operating. VEVOR reserves the right to interpret the user manual. The product appearance is subject to the received item. VEVOR will not provide further notice for technology or software updates.

INSTRUCTIONS

Thank you for choosing this product. Please read all instructions before use to achieve the best results.

PLEASE NOTE! Drawings in this manual are for illustration purposes only and may differ in some details from the actual product.

ATTENTION! Read all safety warnings and instructions. The "wedding arch backdrop stand" is referred to throughout these warnings. This product is not a toy. Do not allow children to play with this item. Place it where children cannot climb to avoid injury from falling.

USAGE SAFETY

1. Before installation, verify that all parts listed in the manual are present in the packaging. Contact your seller if any parts are missing.
2. Select a clean assembly area free of debris to prevent tripping hazards.
3. Review the assembly instructions in the operator's manual before proceeding.
4. After assembly, thoroughly inspect the product to ensure all nuts and bolts are tightened.
5. This product is not a climbing frame or hanging tool and should only be used as a wedding arch backdrop stand.
6. Parts not marked "x FT" in the parts list are general parts of different size brackets and can be installed according to the instructions.

SAVE THESE INSTRUCTIONS

SPECIFICATIONS

PARTS LIST

8 ft

The 8ft model consists of the following parts:

• Part A: Vertical support (2 pieces)
• Part B: Horizontal base connectors (8 pieces)
• Part C: Base crossbar (1 piece)
• Part D: Base crossbar (2 pieces)
• Part E: Base crossbar (1 piece)
• Part F: Curved arch segment (2 pieces)
• Part G: Curved arch segment (3 pieces)
• Part H: Curved arch segment (1 piece)
• Part I: Wing nuts (18 pieces)
• Part J: Screws (2 pieces)
• Part K: Allen wrench (1 piece)
• Part M: Ground stakes (4 pieces)

7.2 ft

The 7.2ft model consists of the following parts:

• Part A: Vertical support (2 pieces)
• Part B: Horizontal base connectors (8 pieces)
• Part C: Base crossbar (1 piece)
• Part D: Base crossbar (1 piece)
• Part E: Base crossbar (1 piece)
• Part F: Curved arch segment (2 pieces)
• Part G: Curved arch segment (3 pieces)
• Part L: Curved arch segment (2 pieces)
• Part I: Wing nuts (16 pieces)
• Part J: Screws (2 pieces)
• Part K: Allen wrench (1 piece)
• Part M: Ground stakes (4 pieces)

6.6 ft

The 6.6ft model consists of the following parts:

• Part A: Vertical support (2 pieces)
• Part B: Horizontal base connectors (8 pieces)
• Part C: Base crossbar (1 piece)
• Part D: Base crossbar (1 piece)
• Part E: Base crossbar (1 piece)
• Part F: Curved arch segment (2 pieces)
• Part G: Curved arch segment (3 pieces)
• Part H: Curved arch segment (1 piece)
• Part I: Wing nuts (16 pieces)
• Part J: Screws (2 pieces)
• Part K: Allen wrench (1 piece)
• Part M: Ground stakes (4 pieces)

PRODUCT ASSEMBLY

8ft Assembly

1. Step 1: Assemble Part "8FT F", "8FT G", and "8FT H" as shown using hardware I (wing nuts).
2. Step 2: Assemble Part B as shown using hardware I (wing nuts).
3. Step 3: Assemble Part A as shown using hardware I (wing nuts).
4. Step 4: Assemble Parts "8FT C", "8FT D", and "8FT E" as shown using hardware I (wing nuts). Then use part J (screws) to install them onto the frame. The position of the assembled part I on the component can be adjusted before locking with part J.

7.2ft Assembly

1. Step 1: Assemble Part "7.2FT F", "7.2FT G", and "7.2FT L" as shown using hardware I (wing nuts).
2. Step 2: Assemble Part B as shown using hardware I (wing nuts).
3. Step 3: Assemble Part A as shown using hardware I (wing nuts).
4. Step 4: Assemble Parts "7.2FT C", "7.2FT D", and "7.2FT E" as shown using hardware I (wing nuts). Then use part J (screws) to install them onto the frame. The position of the assembled part I on the component can be adjusted before locking with part J.

6.6 ft Assembly

1. Step 1: Assemble Part "6.6FT F", "6.6FT G", and "6.6FT H" as shown using hardware I (wing nuts).
2. Step 2: Assemble Part B as shown using hardware I (wing nuts).
3. Step 3: Assemble Part A as shown using hardware I (wing nuts).
4. Step 4: Assemble Parts "6.6FT C", "6.6FT D", and "6.6FT E" as shown using hardware I (wing nuts). Then use part J (screws) to install them onto the frame. The position of the assembled part I on the component can be adjusted before locking with part J.

If the arch backdrop stand is installed on soft ground (e.g., grass), it can be reinforced with part "M" (ground stakes).

Manufacturer: Shanghaimuxinmuyeyouxiangongsi

Address: Shuangchenglu 803nong11hao1602A-1609shi, baoshanqu, shanghai 200000 CN

Imported to AUS: SIHAO PTY LTD. 1 ROKEVA STREET EASTWOOD NSW 2122 Australia

Imported to USA: Sanven Technology Ltd. Suite 250, 9166 Anaheim Place, Rancho Cucamonga, CA 91730

EU Representative: E-CrossStu GmbH, Mainzer Landstr.69, 60329 Frankfurt am Main.

UK Representative: YH CONSULTING LIMITED, C/O YH Consulting Limited Office 147, Centurion House, London Road, Staines-upon-Thames, Surrey, TW18 4AX

VEVO® TOUGH TOOLS, HALF PRICE

Technical Support and E-Warranty Certificate

www.vevor.com/support