Diagram showing an L-shaped sofa (Right Facing) transforming into a U-shaped sofa with an arrow → indicating the change.
Diagram showing an L-shaped sofa (Left Facing) transforming into a U-shaped sofa with an arrow → indicating the change.
PRE-ASSEMBLY INFORMATION
?? TWO PERSON ASSEMBLY ⌛️ UP TO 30 MINUTES FOR ASSEMBLY
?️ LBS ONE SEAT WEIGHT LIMITATION: 300LB ? VACUUM COMPRESSION
Thank you for choosing our product. To ensure safe and satisfactory use of this product, please carefully read the below instructions before assembly.
HOW MANY PACKAGES INCLUDED?
L shaped sofa: 2 Boxes (A/B)
U shaped sofa: 3 Boxes (A/B/C)
ASSEMBLY REQUIREMENT
2 PERSON ASSEMBLY I 20-30 MINUTES ASSEMBLY TIME (APPROXIMATE)
ASSEMBLY PREPARATION
- Remove all packaging materials, hardware and parts from the carton.
- Refer to Parts List and ensure they are complete before you start assembling.
- Place all components on a clean, flat and soft surface (e.g. carpet or rug) to prevent parts from getting scratched.
Catalogue
Part List.....................................................................................................................3
Sofa Legs Assembly.....................................................................................................5
Install the Swift-loks on sofa chaise................................................................................6
Connect Sofa Base & Armrest.......................................................................................9
Connect Backrest Frame and Cover it...........................................................................13
Insert Backrest Into Armrest........................................................................................15
Footrest Assembly.....................................................................................................16
How to replace USB...................................................................................................21
Parts List
Box A Parts List
A Sofa Base: 1pc
D Armrest(D): 1pc
E Seat Cushion: 1pc
G Backrest Pillow: 2pcs
H Throw Pillow: 1pc
K Backrest Cover(K): 1pc
L Footrest: 2pcs
M Storage Basket: 1pc
W Power: 1pc
X Liner: 1pc
A1 Footrest cushion: 1pc
E1 Connection rods: 1pc
Diagram illustrating the Accessory Box, showing it contains various hardware parts.
Parts Contained in the Accessory Box
N Swyft-loks(N): 2pcs big
O Swyft-loks(O): 6pcs small
P Leg and Plastic Washer: 8pcs
Q Plastic Plug: 2pcs
R Screw M6*40mm: 4pcs
S Screw M6*16mm: 36pcs
T Screw M6*30mm: 3pcs
U Allen Key: 1pc
V Wheel: 4pcs
D1 Swyft-loks(D1): 2pcs big
G1 Angle iron: 1pc
H1 Metal Washer: 4pcs
F1 Angle iron: 1pc
Box B Parts List
B Chaise: 1pc
C Armrest(C): 1pc
F Chaise Cushion: 1pc
G Backrest Pillow: 2pcs
H Throw Pillow: 1pc
I Iron Frame(I): 1pc
J Iron Frame(J): 1pc
B1 Front bezel: 1pc
Box C Parts List
B Chaise: 1pc
F Chaise Cushion: 1pc
G Backrest Pillow: 1pc
N Swyft-loks(N): 2pcs big
O Swyft-loks(O): 2pcs small
P Leg and Plastic Washer: 4pcs
R Screw M6*40mm: 2pcs
S Screw M6*16mm: 8pcs
XY Iron Frame with Backrest Cover: 1pc
H1 Metal Washer: 2pcs
Assembly Instructions
Step 1: Installation of sofa legs with plastic washers
Diagram shows sofa base components labeled B, C, and D. Component B has four leg attachment points. Components C and D each have two. A close-up illustrates attaching a leg (P) with a plastic washer (P) to a base component using a screw. The diagram indicates a total of 12 legs (P) are used.
Step 2: Fix the swyft-loks (D1) to the armrests with M6*16mm screws (S)
Diagram shows armrest components. Swyft-loks (D1) are attached using M6*16mm screws (S) and an Allen key (U). A close-up details the orientation of D1, S, and U.
Step 3: Fix the swyft-loks (O) to Sofa Base (A) with M6*16mm screws (S)
Diagram shows Sofa Base (A). Swyft-loks (O) are attached using M6*16mm screws (S) and an Allen key (U). A note specifies the base and swyft-lok orientation (downwards). A close-up shows the attachment.
Step 4: Please decide the direction of the sofa chaise before your start installation.
Check the instructions carefully and install the Swyft-loks in the direction you want the recliner to go, which determines whether the chaise is on the left or the right.
L-Shape Configuration
Illustrates two L-shaped sofa configurations: "L shaped sofa (Right Facing)" and "L shaped sofa (Left Facing)". It shows how components B (chaise) and N/O (swyft-loks) are attached using Allen key (U) and screws (S). Close-ups show the connection points.
U-Shape Configuration
Note that the Swyft-loks on the two chaises must be installed opposite each other as shown.
Shows a U-shaped sofa configuration. Components B (chaise) and N/O (swyft-loks) are attached to form the U-shape. Close-ups detail the use of Allen key (U), screws (S), and swyft-loks (N/O).
Step 5: Connect sofa base & armrest
L-Shape (Left Facing)
Shows connecting armrest (D) to chaise (B) first. Uses connecting rod (E1), angle irons (F1), screws (S), and Allen key (U). A note explains the Velcro side of the rod and the position of iron plates. Close-ups show the connection.
L-Shape (Right Facing)
Shows connecting armrest (C) to chaise (B) first. Uses connecting rod (E1), angle irons (G1), screws (S), and Allen key (U). Similar notes and close-ups as the left-facing configuration.
U-Shape
Note that the Swyft-loks on the two chaises must be installed opposite each other as shown.
Shows attaching left and right armrests to each chaise for a U-shaped sofa. Uses connecting rod (E1), angle irons (F1, G1), screws (S), and Allen key (U). Notes and close-ups are similar to previous steps.
Step 6: Install the sofa base.
Please kindly note that the small round metal insert part O is inserted into the large square metal insert part N.
Shows installing the sofa base (A) onto components B, C, D for both L-shape and U-shape configurations. Arrows indicate the insertion of part O into part N.
Step 7: Fasten part I & J fittings with the screws R and washers H1.
L-Shaped Sofa & U-Shaped Sofa
Shows iron frames I and J being assembled using screws (R) and washers (H1) with Allen key (U). A note advises not to tighten screws until aligned. Cover K is then placed on frames I and J.
U Shaped Sofa ONLY
Shows fastening part XY and part I using screws (R) and washers (H1) with Allen key (U). Mentions removing Swyft-loks from part I and opening the zipper of XY. A note emphasizes screw insertion direction.
Step 8: Insert the backrest into the sofa.
For L-shape and U-shape, shows inserting iron frames I and J into the sofa. A note explains the correct orientation based on metal clasp placement and distance.
Step 9: Insert Plastic PART Q into backrest Side.
For L-shape and U-shape, shows inserting two plastic parts (Q) into the backrest sides.
Step 10: Fasten the 4 wheels (V) to the iron frame with screws M6*16mm (S).
Shows attaching four wheels (V) to the iron frame using screws (S) and Allen key (U). A close-up shows the attachment detail.
Step 11: Wrapping the Velcro around the iron frame to secure the storage basket (M).
Shows securing the storage basket (M) to the iron frame using Velcro straps. One basket (M) is used.
Step 12: Fix the panel (B1) on the iron frame with M6*30mm screws (T).
Shows attaching panel B1 to the iron frame using screws (T) and Allen key (U). A close-up shows the connection.
Step 13: Place Liner (X) in the storage area of footrest.
Shows placing liner X into the footrest storage area.
Step 14: Place the cushion (A1) on the Footrest (L).
A note states the back of the fabric is covered with Velcro.
Shows placing cushion A1 onto the footrest L.
Step 15: Attach the fabric to the underside of the backing board.
Note: Please completely cover the footrest support board with fabric and place Velcro on the bottom of the support board.
Shows attaching fabric to the underside of the footrest backing board.
Step 16: Please lift up the footrest L so that the wheels are above the iron frame before sliding into the sofa.
For L-shape and U-shape, shows a person lifting the footrest (L) and pushing it inward. Arrows indicate 'Up' (↑) and 'Push inward' actions.
Step 17: Put cushions and pillows on the sofa.
L-Shape Sofa
Shows the placement of seat cushions (E), chaise cushions (F), backrest cushions (G), and throw pillows (H) on the assembled L-shaped sofa.
U-Shape Sofa
Shows the placement of seat cushions (E), chaise cushions (F), backrest cushions (G), and throw pillows (H) on the assembled U-shaped sofa.
How To Replace USB?
Diagrams illustrate the process of replacing a USB module, likely integrated into the sofa. This involves unscrewing the old unit, pulling out the USB cable, and installing a new USB unit.
Cushion Care
Your cushions come vacuum packed and sealed for shipping. To restore the cushion's original shape, follow the steps below.
After packing up, place them somewhere dry and ventilated. After about 72 hours it can be restored to its best-use condition.
Diagrams show cutting open vacuum-sealed cushions, then plumping them by patting around the edges. Arrows indicate the direction of plumping.
Uneven Fabric is a normal phenomenon that the first time you open it, the fabric is uneven. Because the fabric is easy to crease after long time transport in vacuum compression. You can use an iron to smooth it out, have a try!
