ASSEMBLY INSTRUCTION
Introduction
Legs and hardware are stored in the box, please take out for assembly.
⚠️ NOTE: Do not use power tools for assembly. Power tools increase the risk of over tightening which lead to splitting or cracking the wood.
Parts Identification
Location of KD parts
KD parts are typically 'knock-down' or flat-packed components.
The document identifies parts for a 2-Seater section and a Chaise section.
2-SEATER PART LIST
| No. | Description | Diagram | Quantity |
|---|---|---|---|
| A | POP-UP SLEEPER SEAT | [Seat Base] | 1 |
| B | LSF ARM (Arm for LC) | [Left Side Armrest] | 1 |
| C | RSF ARM | [Right Side Armrest] | 1 |
| D | ROUND PLASTIC LEG 50x50x50mm | [Plastic Leg] | 4 |
| E | CASTOR | [Castor Wheel] | 4 |
| F | BACK CUSHION RSF | [Right Back Cushion] | 1 |
| G | PILLOW 18"x18" (Packed in LC) | [Pillow] | 1 |
| H | BACK REST (Packed in LC) | [Backrest Panel] | 1 |
| I | METAL BRACKET | [Metal Bracket] | 2 |
CHAISE PART LIST
| No. | Description | Diagram | Quantity |
|---|---|---|---|
| J | CHAISE SEAT | [Chaise Seat Base] | 1 |
| K | BACK REST | [Chaise Backrest Panel] | 1 |
| L | PLASTIC LEG 150x50x50mm (packed in 2R) | [Longer Plastic Leg] | 3 |
| M | BACK CUSHION LSF (packed in 2R) | [Left Back Cushion] | 1 |
| I | METAL BRACKET (packed in 2R) | [Metal Bracket] | 2 |
| G | PILLOW 18"x18" | [Pillow] | 1 |
| D | ROUND PLASTIC LEG 50x50x50mm (packed in 2R) | [Plastic Leg] | 2 |
HARDWARE LIST
| No. | Description | Diagram | Quantity |
|---|---|---|---|
| SCREW Ø8x45MM | [Screw] | 12 | |
| SCREW Ø8x25MM | [Screw] | 16 | |
| Note: Some hardware may be pre-attached or not included in separate packaging. | |||
Assembly Steps
Step 1
Attach four round plastic legs (D) to the underside of the 2-seater seat base (A) using screws. A screwdriver ? is shown.
Step 2
Attach four castors (E) to the underside of the 2-seater seat base (A) using screws (N). A screwdriver ? is shown.
Step 3
Attach two metal brackets (I) to the sides of the 2-seater seat base (A). Arrows indicate the orientation and insertion points.
Step 4
Attach three plastic legs (L) to the underside of the chaise seat unit (J) using screws. A screwdriver ? is shown.
Step 5
Attach two metal brackets (I) to the sides of the chaise seat unit (J). Arrows indicate the orientation and insertion points.
Step 6
Attach the RSF arm (C) to the right side of the 2-seater seat base (A) using screws. An arrow indicates upward movement for attachment.
Step 7
Connect the chaise seat unit (J) to the 2-seater seat base (A). The metal brackets attached in Steps 3 and 5 will interlock. Arrows indicate lifting and joining the two sections.
Step 8
Attach the LSF arm (B) to the left side of the assembled unit (A+J) using screws. An arrow indicates upward movement for attachment.
Step 9
Attach back rests. Insert back rest panels (K) into the chaise seat unit (J) and back rest panels (H) into the 2-seater seat base (A). Arrows indicate downward placement.
Step 10
Place back cushions. Position the left back cushion (M) onto the chaise section (J) and the right back cushion (F) onto the 2-seater section (A). Arrows indicate downward placement.
Step 11
The assembled sofa sleeper (labeled LC and 2R) is shown. It includes integrated USB charging ports ? and an electrical outlet ⚡.
Step 12
The sofa can be converted into a bed. Place pillows (G) as desired for comfort.
Care Instructions
Care Instruction for Boucle Furniture:
In order to maintain the original appearance of your Boucle furniture, please follow below simple care procedures:
- Avoid exposing furniture directly to sunlight or heating and air conditioning outlets. Sunlight and/or exposure to heating and air conditioning outlets will fade/damage Boucle.
- Vacuum or wipe with a soft cloth to remove dust.
- Hardware may loosen over time. Periodically check to make sure all connections are tight, re-tighten if necessary.
⚠️ For item use on wooden floor, hard surfaces or carpets, it is recommended to install protective pads under all legs and supports to avoid/prevent from damages/scratches and discoloration.
