Latitude Run L-Shaped Sleeper Sectional Sofa Assembly Instructions
Introduction
This document provides step-by-step instructions for assembling your Latitude Run L-Shaped Sleeper Sectional Sofa with Storage Chaise and Pull Out Couch.
Chaise Assembly
This section details the assembly of the chaise component.
Chaise Main Structure Accessories
- A: Long bar (9pcs)
- A1: Long bar (2pcs)
- C1: Side panel (1pc)
- D2: Base support panel (1pc)
- D3: Front base panel (1pc)
- E1: Side panel (1pc)
- F: Seat cushion (1pc)
- F3: Back cushion (1pc)
- F4: Decorative element/strap (1pc)
- H1: Frame base (1pc)
- Q: Drawer/storage base panel (1pc)
Chaise Hardware Parts
- V: Screw M6X17mm (10pcs)
- P: M8 Spanner (1pc)
Chaise Structural Accessories
- L: Support bracket (1pc)
- L1: Support bracket (1pc)
- W: Bracket (1pc)
- X: Bracket (1pc)
- M: Cylindrical support/connector (1pc)
- W1: Bracket (1pc)
- X1: Bracket (1pc)
- O: Foot/base pad (4pcs)
Assembly Steps (Chaise)
STEP 1
Attach side panel C1 to base support panel D2 using cylindrical support M.
Diagram shows C1 being attached to D2 with M.
STEP 2
Attach bracket X to base support panel D2 using screws P and cylindrical support M. Note: "First loosen the screws, then install the bracket, locken the screws later."
Diagram shows X being attached to D2 with M and P.
STEP 3
Attach front base panel D3 to the assembly using bracket W and screws P. Note: "First loosen the screws, then install the bracket, locken the screws later."
Diagram shows D3 being attached with W and P.
STEP 4
Attach side panel C1, base support panel D2, and front base panel D3 using screws P. Note: "First loosen the screws, install the mounting plate and lock the screws."
Diagram shows C1, D2, D3 being connected with P.
STEP 5
Attach the drawer/storage base panel Q.
Diagram shows Q being attached to the frame.
STEP 6
Attach bracket X1 to panel E1 using bracket W1 and screws P. Note: "Note that accessories distinguish left and right, after installation and lock the screws."
Diagram shows X1 attached to E1 with W1 and P.
STEP 7
Attach screws P.
Diagram shows P being attached.
STEP 8
Attach support bracket L1 to the frame using screws V. Note: "Note that accessories distinguish left and right, after installation and lock the screws."
Diagram shows L1 being attached with V.
STEP 9
Attach frame base H1 using support bracket L, screws V, and P. Note: "Easier to install when tilted."
Diagram shows H1 being attached with L, V, P.
STEP 10
Place the part A1 in the second position, ensuring the Velcro side is facing up.
Diagram shows A1 being placed. Note: "Place the A1 in the second position and note that the Velcro side is facing up."
Two-Seater Assembly
This section details the assembly of the two-seater component.
Two-Seater Main Structure Accessories
- B: Long bar (9pcs)
- B1: Long bar (2pcs)
- C: Side panel (1pc)
- D: Base support panel (1pc)
- D1: Base support panel (1pc)
- F: Seat cushion (2pcs)
- F1: Back cushion (1pc)
- F5: Decorative element/strap (1pc)
- G: Support bar (1pc)
- J: Frame base (1pc)
- J1: Frame base (1pc)
- Z: Side panel (1pc)
Two-Seater Hardware Parts
- V: Screw M6X17mm (4pcs)
- N: Screw M8X30mm (6pcs)
- Y: Screw M8X18mm (3pcs)
- U: Screw M5X14mm (4pcs)
Two-Seater Structural Accessories
- M: Cylindrical support/connector (2pcs)
- O: Foot/base pad (22pcs)
- W: Bracket (1pc)
- X: Bracket (1pc)
Assembly Steps (Two-Seater)
STEP 1
Attach side panel C to panel Z using screws N and P. Note: "Note that the hole of the buckle faces upward and the countersunk hole faces outward."
Diagram shows C attached to Z with N and P.
STEP 2
Attach side panel C using cylindrical support M and screw P. Note: "Loosen the screws properly first for better engagement."
Diagram shows C being attached with M and P.
STEP 3
Attach base support panels D and D1 to frame bases J and J1 using screws V and P.
Diagram shows D and D1 attached to J and J1 with V and P.
STEP 4
Attach brackets W and X to panels D and D1 using screws P. Note: "Loosen the screws properly first for better engagement."
Diagram shows W and X attached to D and D1 with P.
STEP 5
Reinforce the structure using screws U and P. Note: "Tips: Self-tapping screw is an auxiliary reinforcement function, you can choose to reinforce or not."
Diagram shows U being attached with P.
STEP 6
Attach side panel C and base support panel D1 to the mounting plate using screws P. Note: "First loosen the screws, install the mounting plate and lock the screws."
Diagram shows C and D1 being attached with P.
STEP 7
Attach support bar G to panels D and D1 using screws P. Note: "Loosen the screws properly first for better engagement."
Diagram shows G attached to D and D1 with P.
STEP 8
Place the part B1 in the second position, ensuring the Velcro side is facing up.
Diagram shows B1 being placed. Note: "Place the B1 in the second position and note that the Velcro side is facing up."
Mattress and Frame Assembly
This section covers the mattress and its supporting frame assembly.
Mattress & Frame Main Structure Accessories
- A: Long bar (9pcs)
- A1: Long bar (2pcs)
- E: Side panel (1pc)
- F2: Mattress (1pc)
- F4: Decorative element/strap (2pcs)
- H: Frame base (1pc)
- K: Support bracket (1pc)
- K1: Support bracket (1pc)
- S: Vertical support (1pc)
- S1: Vertical support (1pc)
- Z1: Long bar (1pc)
Mattress Hardware Parts
- V: Screw M6X17mm (4pcs)
- N: Screw M8X30mm (3pcs)
- Y: Screw M8X18mm (6pcs)
- U: Screw M5X14mm (4pcs)
Mattress Structural Accessories
- O: Foot/base pad (22pcs)
Assembly Steps (Mattress & Frame)
STEP 1
Attach vertical support S1 to side panel E using screws N and P. Note: "Install countersunk holes facing outward."
Diagram shows S1 attached to E with N and P.
STEP 2
Attach vertical support S to the assembly using screw P. Note: "Loosen the screws properly first for better engagement."
Diagram shows S attached to the assembly with P.
STEP 3
Attach screws U using P. Note: "Tips: Self-tapping screw is an auxiliary reinforcement function, you can choose to reinforce or not."
Diagram shows U being attached with P.
STEP 4
Attach support brackets K1 and K to frame base H using screws V and P.
Diagram shows K1 and K attached to H with V and P.
STEP 5
Attach vertical supports S and K1 to side panel E using screws Y and P.
Diagram shows S and K1 attached to E with Y and P.
STEP 6
Place parts A1 and A in their positions, noting the Velcro side of A1 faces up. Note: "Place the A1 in the second position and note that the Velcro side is facing up."
Diagram shows A1 and A being placed.
STEP 7
Pull the drawstring to adjust the supporting frame.
Diagram shows a drawstring being pulled to adjust a frame.
STEP 8
Secure the mattress F2 in place using Velcro. Note: "Secure it in place, using Velcro."
Diagram shows F2 being secured with Velcro.
Sectional Assembly (Plan A & Plan B)
This section details how to connect the chaise and two-seater sections, with two possible configurations.
Plan A: CHAISE on the Left
Follow these steps to assemble the sectional with the chaise on the left side.
Assembly Steps (Plan A)
STEP 1
Attach armrest R1 to the chaise using cylindrical support M.
Diagram shows R1 being attached to the chaise with M.
STEP 2
Connect armrest R1 to the chaise.
Diagram shows R1 being slid into place.
STEP 3
Insert the left armrest R1 into the left side of the chaise.
Diagram shows insertion of R1.
STEP 4
Connect the armrest.
Diagram shows connection points.
STEP 5
Attach armrest R2 to the two-seater using cylindrical support M.
Diagram shows R2 being attached to the two-seater with M.
STEP 6
Connect armrest R2 to the two-seater.
Diagram shows R2 being slid into place.
STEP 7
The right-side of the two-seater: insert the right armrest R2.
Diagram shows insertion of R2.
STEP 8
Connect the armrest.
Diagram shows connection points.
STEP 9
Connect the chaise and the two-seater sections.
Diagram shows the two main sections being brought together.
STEP 10
The right-side of the chaise inserts the left side of the two-seater.
Diagram shows the connection detail.
STEP 11
Connect the sections.
Diagram shows connection points.
STEP 12
Lock the screws using parts N and P.
Diagram shows N and P being used to lock screws.
STEP 13
Screw through the hole and tighten with the butterfly nut T, using parts N and P. Note: "Screw through hole and tighten with butterfly nut."
Diagram shows T, N, P used for tightening.
STEP 14
Lift it slightly and place it on the track.
Diagram shows the assembled unit being placed on a track.
STEP 15
Final positioning of the assembled unit.
Diagram shows the assembled unit in its final position.
STEP 16
Place the cushions F, F1, F2, F3, and F4 onto the sofa frame.
Diagram shows cushions being placed on the sofa.
Plan B: CHAISE on the Right
Follow these steps to assemble the sectional with the chaise on the right side.
Assembly Steps (Plan B)
STEP 1
Attach armrest R2 to the chaise using cylindrical support M.
Diagram shows R2 being attached to the chaise with M.
STEP 2
Connect armrest R2 to the chaise.
Diagram shows R2 being slid into place.
STEP 3
The right-side of the chaise: insert the right side armrest R2.
Diagram shows insertion of R2.
STEP 4
Connect the armrest.
Diagram shows connection points.
STEP 5
Attach armrest R1 to the two-seater using cylindrical support M.
Diagram shows R1 being attached to the two-seater with M.
STEP 6
Connect armrest R1 to the two-seater.
Diagram shows R1 being slid into place.
STEP 7
Insert the left armrest R1 into the left side of the two-seater.
Diagram shows insertion of R1.
STEP 8
Connect the armrest.
Diagram shows connection points.
STEP 9
Connect the chaise and the two-seater sections.
Diagram shows the two main sections being brought together.
STEP 10
The right-side of the two-seater inserts the left side of the chaise.
Diagram shows the connection detail.
STEP 11
Connect the sections.
Diagram shows connection points.
STEP 12
Lock the screws using parts N and P.
Diagram shows N and P being used to lock screws.
STEP 13
Screw through the hole and tighten with the butterfly nut T, using parts N and P. Note: "Screw through hole and tighten with butterfly nut."
Diagram shows T, N, P used for tightening.
STEP 14
Lift it slightly and place it on the track.
Diagram shows the assembled unit being placed on a track.
STEP 15
Final positioning of the assembled unit.
Diagram shows the assembled unit in its final position.
STEP 16
Place the cushions F, F1, F2, F3, and F4 onto the sofa frame.
Diagram shows cushions being placed on the sofa.
Finished Product Display
The final assembled product is an L-shaped sleeper sectional sofa with a storage chaise and pull-out couch.
Diagram shows the completed L-shaped sofa.
