Product Instruction
⚠️ WARNING
Serious or fatal crushing injuries can occur from furniture tip-over. To help prevent tip-over:
- Place heaviest items in the lowest drawers.
- Do not set TVs or other heavy objects on the top of this product.
- Never allow children to climb or hang on drawer, door, or shelves.
- Never open more than one drawer at a time.
- Use of tip-over restraints will only reduce but not eliminate the risk of tip-over.
MAINTENANCE TIPS
- Avoid liquid spraying or infiltrating on the product surface.
- Never use chemical cleaning products. They will damage the finish.
- To avoid dulling of finish, do not place furniture in direct sunlight.
- Do not put plastic or rubber rings under appliances. Use cloth of felt protectors.
- To clean, use a soft or slightly damp cloth, and wipe with a clean and dry cloth.
Assembly Information
General Guidance:
- Tooling: A hammer (?) is shown as a required tool. A screwdriver (?) and remote control are shown crossed out (❌), indicating they are not needed or not recommended for certain steps.
- Part Handling: Ensure parts are handled correctly to prevent damage. A diagram shows a person receiving a panel correctly, contrasting with a depiction of damaged parts.
- Surface Protection: Protect your assembly surface. A diagram illustrates a drawer being damaged when placed directly on the floor, versus being protected when placed on a rug.
- Important Information: Please read and save this information carefully.
Cam Lock System
The cam lock system requires the nut to be centered within the cam lock when joining two panels. The cam lock itself should be inserted before the nut.
Hardware List
- A: 20PCS (M3.5x14)
- B: 20PCS (M4x12)
- C: 10PCS (M3.5x30)
- D: 3PCS
- E: 1PCS
- F: 2PCS
- G: 2PCS
- H: 24PCS
- I: 6PCS
- J: 4PCS
- K: 4PCS
- L: 2PCS
- M: 2PCS
- N: 2PCS
- O: 2PCS
- P: 1PCS
- Q: 4PCS
- R: 4PCS
Parts List
The cabinet is comprised of numbered parts: 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15, 16, 17, 18.
Assembly Steps
Step 1
Attach side panels (2 and 3) to the base panel (1). Secure using screws (A) and dowels (H). Detail shows correct insertion of dowels (H) and screws (A). Also attach part 9. Hardware used: A x16, H x12, with specific counts for left/right sides.
Step 2
Connect part 1 to part 9. Use hardware A, L, and I. Hardware used: A x4, L x2, I x2.
Step 3
Attach part 1 to part 7 using hardware B and C. Hardware used: B x2, C x1, E x1.
Step 4
Connect part 7 to part 9 using hardware B and C. Hardware used: B x2, C x1.
Step 5
Attach part 17 to a base component using hardware G and I. Also attach part 17 using hardware F. Hardware used: G x2, I x4, F x2.
Step 6
Assemble the main cabinet frame using parts 1, 7, 9, 17, 2, and 4. Secure with hardware B and C. Hardware used: B x7, C x4.
Step 7
Insert drawer runners or internal dividers (part 8) and side panel (part 4) into the frame. Part 17 is also positioned. Part P is used. Hardware used: P x1.
Step 8
Attach the top panel (part 3) to the main cabinet structure. Use hardware B and C. Hardware used: B x7, C x4.
Step 9
Assemble the base support structure using parts N, J, and O. Hardware used: O x2, N x2, J x4.
Step 10
Attach the assembled base support to the main cabinet structure using hardware Q. Hardware used: Q x4.
Step 11
Install shelves (parts 11, 12) into the cabinet. Secure using hardware A, C, and B. Hardware used: A x8, C x2, B x8.
Step 12
Assemble drawer components using parts 10, 12, 13, and 14. Secure with hardware B and C. Hardware used: C x2, B x8.
Step 13
Assemble the drawer base (part 15) and sides (parts 12, 13, 14). Secure with hardware K. Hardware used: K x4.
Step 14
Attach the assembled drawer unit to the cabinet. Use hardware H and D. Hardware used: H x8, K x4, with specific counts for left/right sides (D).
Step 15
Final attachment of the drawer unit to the cabinet. Use hardware H and D. Hardware used: H x4, with specific counts for left/right sides (D).
Step 16
The cabinet is now fully assembled.
Step 17
Attach the cabinet doors (parts 5 and 6) using hardware H and M. Hardware used: M x2, H x8.
Step 18: Hinge Adjustment
If doors are not square or aligned, adjust screws on the hinges. Details show side-to-side adjustment (using screws A and B), depth adjustment (using screws A and B), and height adjustment (using screw C). Hardware used for adjustment: H x8.
⚠️ Important Safety Information
Tip-Over Hazard:
- The cabinet can tip over, causing serious or fatal crushing injuries.
- Maximum load capacity: Top shelf 70 lbs, Drawer 25 lbs.
- Ensure the furniture is anchored to the wall to prevent tipping.
General Safety & Maintenance:
- Installation must be performed by a qualified person following assembly instructions.
- Electrical or plumbing fixtures should only be installed by trained professionals.
- Wall fasteners are not included due to varied wall materials; consult a dealer for appropriate fasteners. You are responsible for wall anchoring.
- Keep hardware bags and small parts away from children to prevent choking hazards.
- Failure to follow instructions, unauthorized modifications, or use of non-original parts voids warranty and liability.
- GERMANIA is not liable for damage due to improper installation or lack of wall anchoring.
Contact Information: For questions about products or services, email: feedbackstation@163.com.
Product Registration
Register your product for safety alerts or recalls. Provide contact information, model name, model number, and manufacture date via mail or email to feedbackstation@163.com.
