WYBOT Robotic Pool Cleaner

WYBOT

www.wybotpool.com

NORTH AMERICA

E-mail: support@wybotpool.com

Facebook: @WybotPool

No.30, Zhongnan 4th Street West Zone, TEDA Tianjin, China

All trade names are registered trademarks of respective manufacturers listed.

EUROPE

E-mail: support@wybotpool.com

Facebook: @WybotPool

WYBOTICS CO.,LTD

No.30, Zhongnan 4th Street West Zone, TEDA Tianjin, China

All trade names are registered trademarks of respective manufacturers listed.

[FCC logo] [Intertek logo] [Recycling symbol] [Recycling symbol] [Recycling symbol] [Recycling symbol] [Recycling symbol] [Recycling symbol] [CE logo] [RoHS logo]

INTRODUCTION

Thank you for choosing WYBOT products. Your support means a lot to us. Continuous providing the best solution to free you up from pool cleaning and enjoy your family time is always our pursuit.

WYBOT Robotic Pool Cleaner is dedicated to serving you high efficiency, low power consumption, easy operation and thorough pool cleaning work.

Its unique appearance and reliable functions as one-button activation, powerful suction and scrubbing, fine filtration, smart navigation, remote control, and high compatibility with various pool shapes and constructions materials assure you a convenient, intelligent, and optimal pool cleaning.

Feel free to contact us by Email or visit our website with any questions. We are very glad to hear your advice on our continuous improvement.

SAFETY INSTRUCTIONS

Read the manual carefully before you use the cleaner. Your safety is the most important thing. Please read through and operate the device as per instructions. WYBOT Co., Ltd. is not held liable for any loss or injury caused by improper use.

Warning

Failure to operate the device as per the warnings can result in serious injury, electrocution or death.

1. Use only the accessories recommended or sold by WYBOT Co., Ltd.
2. Dry the charging port after each cleaning. Moisture in the charging socket may cause an electric shock.
3. Do not charge the cleaner when it is running (the indicator is on).
4. Use only the original and authorized power charger. Avoid charging any other devices with this charger. Improper use may result in overheating or corrosive liquid leakage from the battery.
5. Make sure the electrical outlet is protected by a ground fault circuit interrupter (GFCI) and an earth leakage circuit breaker (ELI).
6. Do not use a cord-damaged charger to avoid any electrical shock.
7. Do not try to use an extension cord to connect the charger.
8. Never allow children to ride on the cleaner or play with it as a toy.
9. Do not allow children to operate or maintain the device.
10. Do not enter the pool when the cleaner is working in it.
11. Never expose or charge the device in flammable environments.
12. Only licensed professionals can disassemble the sealing parts of the cleaner.
13. Do not operate the cleaner while the pool filter is running.

Caution

Failure to operate the device as per the warnings can cause damage to the device or personal injury.

1. Charge the unit before first use.
2. Do not put your finger between movable parts, such as the flipper hinge moving cavity. You may be injured by a sudden movement.
3. Do not overcharge the cleaner, which will reduce the battery life.
4. Charge the cleaner prior to being stored for a long time (over 6 months) to maintain an optimal battery life.
5. Disassemble the flipper if you will not use the device for a long time. Improper storage may snap the flipper.
6. Remember to wash and clean the filter basket after each use.
7. Store the cleaner in a cool and ventilated place, away from direct sunshine or any heat source.

Use only the pool cleaner in the following water conditions:

SPECIFICATIONS

PACKAGE CONTENTS

• 1 x Cleaner
• 1 x Charger
• 1 x Flipper
• 2 x Scrapers
• 1 x Retrieving Hook
• 2 x Screws
• 1 x User manual

PRODUCT DIAGRAM

Diagram showing the components of the Osprey 200 SE robotic pool cleaner:

• 1. Flipper & Handle
• 2. Top cover
• 3. Filter tray
• 4. Chassis
• 5. Adjustable wheels
• 6. Fastening clip
• 7. Scraper
• 8. Charger
• 9. Retrieving Hook

PREPARATION

a. Screw tightly included flipper using two screws from either side.

Note: You should insert these two screws in different directions. One should be inserted from the left side, and the other from the right side.

b. Install included scrapers onto the bottom to enhance cleaning capability.

Get Started

Charge your new Osprey 200 SE

The device has a lithium-ion rechargeable battery and needs to be charged before first use and when the battery is low. The charging port is on the bottom of the device.

Charging Instructions:

1. For your important safety, double-check that the device is powered off and the charging port is dry before charging.
2. For reducing fire risk, keep your device and adapter away from direct sunshine or water when charging.

Note on Charging:

1. When charging, ensure your device is at least 3m (approx. 10ft) away from the edge of the pool.
2. The temperature should be between 32°F (0°C) and 95°F (35°C) with RH between 5% and 95% when charging.

If you have installed the flipper after first use, keep the bottom on the floor after inserting the connector. Otherwise, the flipper may be broken.

The adapter has an indicator light: green light indicates charging in progress, and red light indicates the battery is full.

Run your new Osprey 200 SE

Turn on the device and put it into the pool within 3 minutes. The device will beep continuously if it exceeds 3 minutes, then you should relaunch the device.

Operation Steps:

1. Hold the handle and put it vertically into the pool and fully submerge the device.
2. After 5 seconds of auto calibration, the cleaner is ready to clean.
3. The device will automatically move to stop by the wall when finishing cleaning or when the battery is low.
4. Insert the included hook into a pool pole and lift the cleaner out of the pool. Remember to power off the device.

Do a filter cleaning

You need to clean the filter tray after each use. Before opening the top cover, ensure the device is powered off.

1. Unclip cover fasteners and remove the top cover from the cleaner.
2. Take off the filter tray.
3. Rinse off all dirt and debris.
4. Reassemble the cleaner as shown in the diagram.

How to adjust your cleaning path

If your pool shape is irregular or you are not satisfied with the default cleaning pattern, you can change the direction of the adjusting wheels to achieve better cleaning work.

Detach the adjustable wheels

You can see two wheel kits marked A, B, C, and D on the front and rear sides of the chassis. On the wheel stem, you can see a catch inserted. Hold that catch and push it to the inner side; then the wheel kit can be removed.

Reset combination path

Insert the limiting lever on the wheel kit into holes marked A/B/C/D to adjust your cleaning path.

Combination Ways and Usage Scenarios:

For example: combination B-A

MAINTENANCE AND STORAGE

Caution

Follow these steps to store your cleaner to maintain good performance:

1. Ensure the device is powered off.
2. Dry out the cleaner and filter basket.
3. Fully charge the battery.
4. Store the cleaner in a cool and ventilated place, away from direct sunshine, heat sources, and frost, with an ambient temperature between 5°C/41°F and 45°C/113°F.
5. Charge the cleaner every three months to ensure an optimal battery life.

Note: If your device does not work after a long-term low battery life or being off, please contact the after-sales team for help. For your safety, do not attempt to disassemble it without authorization.

TROUBLE SHOOTING GUIDE

If the information listed in the troubleshooting guide cannot solve your problem, please email us for help.

FAQ

WARRANTY

1. WYBOT pool cleaners in the market have been inspected and licensed to be sold as per local laws.
2. The warranty duration for the motor, battery, and PCB is one (1) year from the purchasing date. Consumable parts, including filter basket, brushes, wheels, etc., are beyond warranty.
3. The warranty applies only to original buyers and is not valid for resale or any other kind of transfer.
4. Any damages to the unit caused by improper use, unauthorized repair, or disassembly are not covered by WYBOT Co., Ltd.'s warranty.
5. The order number or record must be presented for any claim or repair within the warranty period.

Due to the need for continuous product improvement, the products in this manual are subject to the real products, and WYBOT Co., Ltd. reserves the right to update products.

If you encounter any problems during use, please contact the after-sales team. For more details, please contact WYBOT website www.wybotpool.com.

WYBOT CUSTOMER CARE

PLEASE CONTACT US BEFORE RETURNING THIS PRODUCT TO THE STORE. EMAIL WYBOT CUSTOMER CARE FOR PROBLEMS AND QUESTIONS. WE WILL RESPOND WITHIN 1 BUSINESS DAY.

Wybot Customer Service:

E-mail: support@wybotpool.com

Tel: 1-866-777-6655

We can only provide after-sales service for products sold by WYBOT authorized retailers and distributors. If you purchased your unit from a different place, please contact your seller for return and warranty issues.