WYBOT Robotic Pool Cleaner User Manual

Introduction

Thank you for choosing WYBOT products. Continuous providing the best solution to free you up from pool cleaning and enjoy your family time is always our pursuit.

WYBOT Robotic Pool Cleaner is dedicated to serving you high efficiency, low power consumption, easy operation and thorough pool cleaning work.

Its unique appearance and reliable functions as one-button activation, powerful suction and scrubbing, fine filtration, smart navigation, remote control, and high compatibility with various pool shapes and constructions materials assure you a convenient, intelligent, and optimal pool cleaning.

Feel free to contact WYBOTICS CO.,LTD by Email or visit our website with any questions. We are very glad to hear your advice on our continuous improvement.

Specifications

Packing List

• 1 x Cleaner
• 1 x Charger
• 1 x Flipper
• 2 x Scrapers
• 1 x Retrieving Hook
• 2 x Screws
• 1 x User manual
• 1 x Quick Start Guide

Product Diagram

a Flipper & Handle: Screwed to the device. Transport and remove the device with it.

b Flow outlet: Two flow outlets on the top of the device for a quick water release.

c Sealed part: Important components are sealed there. For your safety, do not try to disassemble it without authorization.

d Filter Tray: Filter dirt and debris after suction.

e Storage cavity: Store all collected debris.

f Front and Rear Adjustable Wheel: Adjust two adjust wheels to run in a different cleaning pattern.

g Charger: Fully charge the cleaner.

h Scraper: Wipe out the dirt and debris from the pool floor.

i Assembly fastener: Lock and unlock the top cover from the chassis. There are two on either side of the device.

j Device Wheel: Running on the flat floor.

k Hook: Remove the cleaner from the pool.

On/Off Button

Charging Port

Note:

• Do not operate the device when the top cover is broken.
• If there is any liquid leakage from the sealing part, stop charging or running the device.

Get Started

Assemble your new OSPERY 200/200 Max

Install flipper

Take out of the included flipper and two screws and prepare a Phillips head screwdriver. Screw tightly the flipper using two screws from either side.

Note:

• You should insert these two screws in a different directions. One should be inserted from left side, and the other from right side.
• Keep your finger away from the flipper hinge moving cavity. A sudden movement may cause you injury.

Install scrapers

Insert the scrapers into the suction opening, you can hear a "click" after a full insertion into the notched of the opening.

Note:

• You can install the scrapers to knock loose debris and dirt. If your pool floor is not so flat, with tiny protrusions or pits, you may not install it to prevent it from being stuck.

Charge your new OSPERY 200/200 Max

The device has a lithium-ion rechargeable battery, and you need to charge the battery before first use and when the battery is low.

The charging port is on the bottom of the device.

Note:

• When charging, you should ensure your device at least 3m (appr. 10ft) away from the edge of the pool.
• The temperature should be at between 32°F(0℃) and 95°F (35℃) with RH between 5% and 95% when charging.
• If you have installed the flipper after first use, you should keep the bottom on the floor after inserting the connector. Otherwise, the flipper may be broken.

The adaptor has an indicator, it will display green light ? and red light ? to tell you battery is full or not.

Run your new OSPERY 200/200 Max

Turn on the device and put it into the pool within 3 minutes. The device will beep continuously if it exceeds 3 minutes, then you should relaunch the device.

Note:

• For your important safety, you need to double check the device is powered off (no beep sound), and charging port is dry before charging.
• For reducing fire risk, keep your device and adaptor away from direct sunshine or water when charging.

Do a Filter Cleaning

Hold the handle and put it vertically into the pool and fully submerge the device.

Note: To achieve an optimal cleaning performance, you should ensure the water depth of the pool is at least 19.5 in (50 cm) high from the top of the device.

About 12 seconds static on the floor, the cleaner is ready to clean.

The device will automatically move to stop by the edge of its nearest wall when finishing cleaning or battery low.

Insert the included hook into a pool pole and lift the cleaner out of the pool. Remember to power off the device.

Note: You should take the cleaner out vertically to drain inside water out quickly. Press on/off button to turn off the device.

Hold the cover fasteners and unlock them.

Note:

• You should ensure the device is power off when opening the top cover.
• You need to clean the filter basket before being dry.

Take out the filter tray. Shake off all debris and rinse it with clean water. You can also use soft soapy water to keep a better clean.

Note: The side with four protrusions in the corners of the mesh should be placed up.

After rinsing, put the filter tray back into the cleaner and fasten the cover.

Note:

• As electric components inside the cleaner, store the cleaner in a cool and ventilated place, away from direct sunshine or any heat source.
• Charge the cleaner prior to being stored for a long time (over 6 months) to maintain an optimal battery life.

How to Adjust Your Cleaning Pattern

If your pool shape is irregular or you are not satisfied with default cleaning pattern, you can change the direction of the adjustable wheels to have a better cleaning work.

Detach the adjustable wheels

You can see two wheel kits where marking A, B, C, and D on front and rear side of the chassis.

On the wheel stem, you can see a catch inserted in. You can hold that catch and push to the inner side, and then the wheel kit can be removed.

Below is the combination ways and their usage scenario of adjustable wheels, you can refer to it.

For example: combination B-A

Reset combination path

Insert the limiting lever on the wheel kit into holes marking A/B/C to modify your cleaning path.

How to Maintain Your Device

You should follow the steps to store your cleaner to maintain good performance.

1. Ensure the device is power off ?.
2. Dry out the cleaner and filter basket ✔️.
3. Fully charge the battery ?.
4. Store the cleaner in a cool and ventilated place, away from direct sunshine, heat source, frost with an ambient temperature at between 5°C/41 F and 45 °C / 113 F.
5. Charge the cleaner every three months to ensure an optimal battery life.

Note: If your device do not work after a long-term low battery life or being off, please contact after-sale team for help. For your safety, do not try to disassemble it without authorization.

FAQ & Trouble Shooting

Q: Could this cleaner do wall and waterline cleaning?

A: This cleaner is designed for floor cleaning only. It does not support any wall or waterline cleaning.

Q: Will obstacles such as steps, shallow water areas, drains, slopes etc. in the swimming pool affect the running?

A: The machine prefers to run on flat floor. High obstacles will make the device stuck. If you encounter the following situations when using the cleaner, you can check the table and solve them by yourself.

Note: If you can not find a solution from the table, please contact after-sale team.

Troubleshooting for Coverage:

Certification

WYBOT robotic pool cleaners have passed all performance and reliability tests and also has obtained relevant certifications from the countries in which they are sold. you can rest assured.

Certifications: CE, FC, RoHS, C, ETL, Intertek

Due to the need for continuous products improvement, the products in the manual are subject to the real products, and WYBOTICS Co., Ltd. reserves the right to update products.

If you encounter any problems during use, please contact after-sale team. For more details, please contact WYBOTICS website www.wybotpool.com

Wybot Customer Service:

E-mail: support@wybotpool.com

Tel: 1-866-777-6655