Wybot Osprey 200 Robotic Pool Cleaner User Manual
Thank you for purchasing the Wybot™ robotic pool cleaner. Please read this entire manual before using your new robotic pool cleaner. Wybot™ is not responsible for any loss or injury caused by improper use. If you encounter any problems with your Wybot™ product, please contact our customer service for assistance.
Wybot Customer Service:
Email: support@wybotpool.com
Web: www.wybotpool.com
Facebook: @WybotPool
Table of Contents
- IMPORTANT SAFETY INSTRUCTIONS
- 1. Introduction
- 2. List of Supplied Material
- 3. Product Diagram
- 4. Specifications
- 5. Operating Instructions
- 5.1 Assembly before use
- 5.2 To use the robotic cleaner
- 5.3 Cleaning after use
- 5.4 To adjust the operation
- 6. Buzzer Ringtone
- 7. Troubleshooting
- 8. Warranty
IMPORTANT SAFETY INSTRUCTIONS
READ AND FOLLOW ALL INSTRUCTIONS
- Read the manual carefully and use the cleaner in accordance with the manual. Wybot™ is not responsible for any loss or injury caused by improper use.
- Use only accessories recommended or sold by the manufacturer.
- This model is only applicable to swimming pools with a flat bottom.
- Do not let children climb on the cleaner or play with it as a toy.
- Use only the original and authorized charging adapter.
- The adapter cord must be repaired or replaced only by a qualified electrician.
- Do not turn on the cleaner when it is out of the water.
- The charging adapter must be connected to a leakage-protected and grounded socket when charging.
- Do not operate the cleaner when there are people in the pool.
- Always clean and wash the filter basket after use.
- Turn off the cleaner during maintenance, cleaning, or when it is not in use.
- The cleaner should be stored in a cool, ventilated place, away from direct sunlight.
- During charging, the cleaner should be kept in a cool place and should not be covered with anything to avoid damaging the internal electrical components due to overheating.
- Only certified professionals can disassemble the sealed drive kit of the cleaner.
- Do not operate the cleaner when the pool filter is running.
- The oil seals of the motor contain grease, which may cause water pollution in case of grease leakage.
- Due to limited battery capacity, the cleaner is only suitable for pools with a maximum size of 46.4 m² (500 ft²), otherwise the cleaning effect will be affected.
- When the cleaner is stored for a long period, it should be recharged every three months to maintain the battery level between 40% and 60%. Please use only the original and authorized charging adapter. If the cleaner is not charged for a long time, the battery voltage will be lower than the over-discharge protection voltage due to battery self-discharge, which may cause fatal damage.
- Do not use or store the cleaner near a heat source.
- Do not pierce the cleaner shell with nails or other sharp objects. Do not hammer, hit, or throw the cleaner.
- Make sure the charging port is dry before charging the device.
KEEP THESE INSTRUCTIONS
1. Introduction
The Wybot Osprey 200 ecological pool cleaner is a new type of automatic rechargeable cleaner that filters pool water and removes particles without replacing the pool water.
2. List of Supplied Material
| Article | Name | QTY (pc) | Remark |
|---|---|---|---|
| 1 | Cleaner | 1 | In the carton |
| 2 | Charger | 1 | In the carton |
| 3 | Flap | 1 | In the carton |
| 4 | Recovery Hook | 1 | In the carton |
| 5 | Screw | 2 | In the plastic bag |
| 6 | Scraper | 2 | In the plastic bag |
| 7 | User Manual | 1 | In the plastic bag |
| 8 | Quick Guide | 1 | In the carton |
3. Product Diagram
Charger
Scraper
Flap
Upper Cover
Filter Basket
Chassis
Recovery Hook
4. Specifications
| Product Name | WYBOT Pool Cleaner |
| Model | Osprey 200 |
| Rated Operating Voltage | 11.1V |
| Power | approx. 30W |
| Operating Cycle | max. 50min |
| Adapter Rated Input Voltage | 100Vac-240Vac |
| Adapter Rated Input Frequency | 47Hz-63Hz |
| Adapter Rated Output Voltage | 12.6Vdc |
| Adapter Rated Output Current | 1A |
| Battery Capacity | 2600mAh |
| Charging Time | 3-4 H |
| Cleaning Area | max. 46.4m² / 500ft² |
| Filter Capacity | approx. 32gal/min (121.1L/min) |
| Filter Density | 180μm |
| Travel Speed | approx. 19.8m/min (65 ft/min) |
| Water Depth | max. 7ft/2.1m |
| IP Class | IPX8 |
| Pool Water Temperature | 50°F-95°F / 10℃-35℃ |
| Charging Environment Temperature | 41°F-95°F / 5℃-35℃ |
| Storage Temperature | 41°F-95°F / 5℃-35℃ |
| Product Weight | 3.6kg / 7.9 lb |
| Product Size | 340 (L) * 350 (W) * 330 (H) mm / 13.4 (L) * 13.8 (W) * 13.0 (H) inches |
5. Operating Instructions
5.1 Assembly before use
- Attach the flap and secure it with the provided screws.
Remark: The installation direction of the 2 screws is opposite.
- Install the scrapers to improve suction effect if the pool bottom is full of debris or particles. It is not recommended to install the scrapers if the pool bottom is uneven or full of holes, which prevents the cleaner from getting stuck by the rough ground.
[Image: Diagram showing how to attach the scrapers to the cleaner.]
- Attach the recovery hook to a standard pool pole (not included).
[Image: Diagram showing the recovery hook attached to a pool pole.]
5.2 To use the robotic cleaner
- Charge the battery
Fully charge the cleaner before each use. Attach the charging connector to the charging port located at the bottom of the cleaner. Place the cleaner in a vertical position, then plug the charger into the main electrical outlet. The charger indicator light should turn red while charging. It should turn green once charging is complete.
REMARK: The robotic cleaner must be charged indoors.
REMARK: It is strictly forbidden to orient the bottom of the device upwards to avoid crushing the oscillating plate during charging.
REMARK: Clean and dry the charging port before charging.
[Image: Diagram showing the cleaner being charged, with the charging port and power button highlighted.]
[Image: Diagram showing incorrect and correct placement of the cleaner for charging.]
- Evacuate the air
Hold the robotic cleaner with both hands and immerse it in the pool. Rotate the robotic cleaner until no more air bubbles come out.
[Image: Diagram showing the cleaner being submerged in the pool to release air.]
- Power on the cleaner
While holding the entire robotic cleaner underwater, turn the product on by pressing the power button located at the bottom. Water will start to flow out of the nozzle after 5 seconds.
[Image: Diagram showing the cleaner underwater with the power button being pressed.]
- Release the robotic cleaner
Hold the robotic cleaner in a vertical position and slowly release the product. The product should slowly sink to the bottom of the pool. If the robotic cleaner is upside down, use the floating handle to correct its orientation.
[Image: Diagram showing the cleaner being released into the pool and sinking to the bottom.]
- Let the cleaner work
The robotic cleaner should travel the pool floor and suck up debris automatically for a maximum of 60 minutes. It will automatically reverse when it touches the wall. The robotic cleaner will automatically move to the pool wall and stop when it runs out of battery.
- Retrieve the cleaner
To retrieve the robot, grasp the flap and pull it out of the water and the pool. Turn off the robot. Use the recovery hook if necessary.
5.3 Cleaning after use
- Open all locking loops, detach the upper cover, and remove the filter basket.
[Image: Diagram showing how to open the cleaner and remove the filter basket.]
- Rinse all dirt and debris under running water.
[Image: Diagram showing the filter basket being rinsed under a faucet.]
- Wipe the robotic cleaner with a clean cloth and let it air dry.
5.4 To adjust the operation
- This robotic cleaner is equipped with two adjustable wheels. By changing the combination of these 2 adjustable wheels, you can change the operating mode of the robotic cleaner.
[Image: Diagram showing the adjustable wheels on the cleaner.]
- To adjust the wheel, open the locking loops and remove the upper cover. Locate the 2 adjustable wheels. Detach the wheel by pushing the wheel shaft lock. Select the correct combination and insert the wheel until the lock snaps into place.
[Image: Diagram showing how to adjust the wheels, highlighting the wheel shaft lock.]
3. Combinations:
- A - C for most pool types (factory setting)
- B - C Smaller bounce angle than A-C
- C - C Minimal maneuverability (for rectangular or longer pools)
- A - B For round pools
[Image: Diagram showing different wheel combinations.]
6. Buzzer Ringtone
| Status | Description |
|---|---|
| Power on | Beep before not fully submerged in water; beep stops after complete submersion in water |
| Power off | Stop sound signal |
7. Troubleshooting
| Problem | Scenario | Possible Cause | Solution |
|---|---|---|---|
| The buzzer does not beep, or the turbine does not work when the cleaner is out of water. | ------- | The battery is low. | Recharge the battery. |
| Internal fault | Call customer service | ||
| The buzzer always beeps, or the turbine does not work when the cleaner is in water. | Internal fault | Internal fault | Call customer service |
| The cleaner does not change direction when it hits the pool wall. | The flap does not tilt forward when approaching the pool wall. | The flap is blocked and does not rotate freely. | Clean the dirt around the flap hinge. Ensure the flap rotates freely. |
| The LED indicator does not light up when the charger is plugged in. | ------- | Defective charger | Call customer service and request a replacement charger. |
| The cleaner does not suck up the entire pool floor, or some areas are always missed. | The cleaner always bounces in the same direction, missing some areas. | Incorrect setting of the operating mode. | Try different operating modes. Refer to the "To adjust the operating mode" section of the manual. |
| Irregular shape of the pool. | |||
| The pool filter is running. | The water flow in the pool affects the cleaner's operation. | Stop the pool filtration pump when using this product. |
8. Warranty
- This product is covered by the Wybot™ warranty for 24 months (only for the drive kit and control box kit) from the date of purchase. Consumable parts are not covered by the warranty, including the filter basket, brush, wheels, and nozzles.
- This warranty is void if the product has been modified, misused, or repaired by unauthorized personnel.
- The warranty extends only to manufacturing defects and does not cover damage resulting from improper handling of the product by the owner.
- The order number or registration must be presented for any claim or repair during the warranty period.
[CE Logo] [RoHS Logo]
Environmental Programs, European WEEE Directive
Please comply with European Union regulations and contribute to environmental protection. Return waste electrical equipment to a designated facility by your municipality that correctly recycles electrical and electronic equipment. Do not dispose of them in unsorted garbage bins. For items containing removable batteries, remove the batteries before disposing of the product.
