VOOPOO DRAG 2 Manual Instruction
Introduction
Thanks for your purchase of a VOOPOO product. For the better use of all the functions of this product, please carefully read the operation notes and detailed functional instructions before your first use of this product. If you have any problems with using this product, please contact your local agent or visit our official website at www.voopoo.com.
Product Description
1. Appearance & Main Parameters
510 Thread: Located at the top of the device.
Power Button: Used for powering on/off and other functions.
Screen: Displays device information and settings.
"+" Up Button: Navigates menus and increases values.
"-" Down Button: Navigates menus and decreases values.
Micro-USB Port: For charging and firmware upgrades.
Parameters:
- Size: 88.3 x 51 x 26.5mm
- Power Output: 5-177W
- Battery: Dual 18650 batteries x 2
- Program upgradable: Yes
Resistance Range:
- Non-TC wire: 0.05-5.0Ω (±5%)
- TC wire: 0.05-1.5Ω (±5%)
2. Electric Parameters
| NO. | Item | Range | Accuracy | Unit |
|---|---|---|---|---|
| 1 | Working voltage | 6.4~8.5 | ±0.1 | V |
| 2 | Output voltage range | 0~7.5 | ±2% | V |
| 3 | Overheat protection | 80 | ±5% | °C |
| 4 | Input charging voltage | 5 | ±0.25 | V |
| 5 | Output charging voltage | 1800 | ±5% | mA |
| 6 | Quiescent currency | ≤10 | - | uA |
| 7 | Temperature Range | 200-600 °F / 100-315 °C | - | °C / °F |
| 8 | Power conversion efficiency | 95% | -5%~0 | % |
3. Eight Security Protections
- Overtime protection
- Over temperature protection
- Output over-current protection
- Overcharge protection
- Low battery protection
- Atomizer short-circuit protection
- Support balance charge with batteries from different manufacturers
- Battery anti-reverse protection
Instructions
1. Basic Operation
- Press the fire button for 5 times: Power on/off. Press the fire button for 3 times: Sequentially switch from Power mode → FIT mode → TC mode.
- Press "+" and "-" buttons simultaneously: Enter function menu.
- Press the fire and "+" buttons simultaneously: Lock/Unlock.
- Press the fire and "-" buttons simultaneously: Switch screen orientation.
2. Four Mode Settings
Power Mode: Displays wattage, voltage, resistance, and battery level.
FIT Mode: Displays "FIT" followed by a number (e.g., FIT 023).
TC Mode: Displays temperature, wire type (e.g., SS), and wattage.
Custom Mode: Displays "M" followed by a number (e.g., M2) indicating the custom profile.
3. Four Mode Operations
A. Power Mode:
Adjust the wattage from 5W to 177W. The product automatically recommends the output wattage according to the resistance of the atomizer when a new atomizer is attached.
Press up and down buttons simultaneously to enter the function menu, which includes:
- Power Mode
- Custom Mode
- Series Number
- Software Version
B. FIT Mode:
Boot default. Press "+" or "-" button to select the three options.
C. TC Mode:
Supports SS, Ni, Ti, NC, TC, 5 kinds of heating wire. Factory default is SS, Ni, Ti. Connect to a computer APP to open NC, TC.
Temperature control adjustable range: 200-600 °F / 100-315 °C.
- When the temperature setting is at 100 °C, keep pressing "-", it will turn to be 600 °F.
- When the temperature setting is at 200 °F, keep pressing "-", it will turn to be 315 °C.
To adjust wattage while in TC Mode, press the fire button 4 times rapidly to activate wattage adjustment. The "W" wattage icon will flash. The wattage can be adjusted from 5W to 80W.
Press "+" and "-" simultaneously to enter the function menu, which includes:
- TC Mode
- Coil Cooling Value
- Custom Mode
- Coil Coefficien
Coil cooling value range: 0.05~1.50Ω.
D. Custom Mode:
Custom mode can be used under Power mode or TC mode.
- Press "+" and "-" simultaneously to enter the function menu, select the [M] icon, and switch between M1 to M5.
- Press the fire button 4 times to switch modes: Power customization (W) → FIT mode → TC customization (SS, Ni, Ti).
Under Custom Mode, there are 2 ways to adjust the value:
- Manually switch custom curve per second: Shortly press the fire button 4 times to enter the curve interface, press UP/DOWN to adjust, then long press the fire button to exit. The display shows the power curve (current watt shown on top right) or TC curve (current temperature shown on top right).
- Connect to a computer app for custom settings.
More Instructions
A. Sleep Mode:
The screen will auto-turn off in 30 seconds without operations and enter standby mode in 30 minutes without operations/usage after the screen is turned off. To activate, press the power button.
B. Charging Mode:
The device enters charging state with the battery icon running when connected to a 5V power supply via USB cable. The battery icon stops running when the device is fully charged.
Note: It takes 3 hours to fully charge the device (5V/2A charger required).
C. Computer Customization:
Customization operations can be performed via the VOOPOO Firmware, including Prompt page, Temperature coefficient, Temperature curve, Wattage Curve, Increase/Decrease Coil type, and Device Upgrade.
Download address: http://www.voopoo.com.
D. Function Tips:
TIME OUT: Indicates a timeout condition.
LOW WATTAGE: Indicates the wattage is too low.
CHECK BATTERY: Indicates a battery issue.
CHECK COIL: Indicates a problem with the coil connection or resistance.
ATOMIZER SHORT: Indicates a short circuit in the atomizer.
NO ATOMIZER: Indicates no atomizer is detected.
ATOMIZER RESISTANCE HIGH: Indicates the atomizer resistance is too high.
HIGH TEMPERATURE: Indicates the device has reached a high temperature limit.
E. Accommodation Coefficient of TC Wire
| Coefficient Range | Standard Default Value |
|---|---|
| Ni: 6000-7000 | 6500 |
| Ti: 3500-4500 | 4000 |
| SS: 1000-1600 | 1300 |
| NC: 20-600 | 400 |
| TC: 100-700 | 1000 |
Note:
- The higher the coil coefficient set, the higher the coil temperature.
- Due to different wire materials, if the power feels insufficient, adjust the coil coefficient higher for a better vaping experience.
- Adjust the coil coefficient at a low rate; setting it too high risks firing cotton.
Attention
- Please keep the device away from heat, fire, and water.
- Please do not drop, throw, or immerse the device in water.
- Please use the proper working mode according to your atomizer's material.
- Please turn off or lock the device to avoid mis-firing when you take it on the go.
- Keep the contents of this package out of reach of children and pregnant women.
- Please use high rate discharge batteries; over 30A is recommended.
- Please do not use batteries with broken skin or which are not completely insulated.
Manufacturer Information
Manufacture: VOOPOO®
Address: Block 1, Shapuyangyong Industry Park, Songgang, Bao'an District, Shenzhen, Guangdong, China.
Email: support@voopootech.com
Website: www.voopoo.com
Instagram: voopootechofficial
Facebook: voopootech
Contact in EU:
Company: Vaping Legal Ltd
Address: Armstrong House, First Avenue, Robin Hood Airport, Doncaster DN9 3GA, UK
Email: compliance@tpdcompliance.eu
Certifications: FCC, CE, RoHS, 18+
Designed by Voopoo in California. Made in China.
