VooPoo Vinci Spark 100 Kit User Manual

Introduction

Thank you for choosing the VooPoo Vinci Spark 100 Kit. Please read this manual carefully for proper and safe use. Contact your supplier for any questions.

The Vinci Spark 100 Kit is a new box mod from the VooPoo Vinci platform, offering elegance and high performance in a compact design for daily use.

Product Specifications

VooPoo Vinci Spark 100 Mod:

• Dimensions: 90.2 x 33 x 28 mm
• Battery: 1x 18650 slot (battery not included)
• Activation: Manual draw
• Output Modes: SMART / RBA / ECO
• Output Power: 5 - 100 W (adjustable)
• Output Voltage: 3.2 - 4.2 V
• Resistance Support: 0.1 - 3.0 Ω
• Charging: USB-C port (5V / 2A)
• Display: TFT 0.96"
• Material: Aluminum Alloy

VooPoo UFORCE-X Nano Tank:

• Length: 57.6 mm
• Diameter: 28 mm (at bubble glass)
• Capacity: 4.5 ml
• Airflow System: Top
• Filling System: Top
• Puffing Style: MTL (Mouth-to-Lung) / RDL (Restricted Direct Lung) / DL (Direct Lung)
• Included Coil Resistance: 0.3 Ω / 0.6 Ω
• Thread: 510
• Weight: 55.9 g
• Material: Stainless Steel + Borosilicate Glass (Pyrex)

This product is not intended for liquids containing nicotine.

Getting Started

Atomizer Setup:

1. Remove the tank from the kit and unscrew its base. If a coil is pre-installed, drip 2-3 drops of e-liquid onto the coil's center. Screw the base with the coil back onto the tank. If the coil is separate, install it first, drip 2-3 drops of e-liquid onto its center, then screw the base back on.
2. To fill the tank, unscrew the [Top Cap] and fill with e-liquid. Never use the center airflow hole for filling; use the smaller side hole with a silicone membrane. Screw the [Top Cap] back on securely.
3. After filling, let the tank stand for at least 10 minutes to allow the e-liquid to saturate the coil. Then, screw the tank onto the mod body.

Battery Installation:

Open the side panel of the device and insert one [18650 Battery] according to the polarity markings. Close the panel. (Battery not included). High-quality cells with an intact wrap and a discharge current of ≥25A are recommended.

Operation

Airflow Adjustment:

Rotate the [Airflow Ring] on the top of the tank to adjust the draw tightness.

Power On/Off:

Press the [Power Button] 5 times quickly to turn the mod on or off.

Main Interface:

The main interface displays:

• Puff Duration: Length of the current puff.
• Output Mode: SMART, RBA, or ECO.
• Resistance: Resistance of the installed coil.
• Power Output: Current wattage setting.
• Puff Count: Number of puffs taken.

Locking/Unlocking the Device:

Use the [Lock/Unlock Switch] located below the adjustment buttons to lock or unlock the device. The display will show "LOCK" when locked and "UNLOCK" when unlocked. The device cannot be fired when locked.

Changing Output Mode:

Press the [Power Button] 3 times quickly to enter the settings menu. Navigate using the [+/- Buttons] and confirm selections with the [Power Button]. Select "MODE" to choose between:

• SMART Mode: Automatically suggests suitable wattage based on coil resistance and limits the adjustable range to prevent coil damage.
• RBA Mode: Standard wattage mode with manual adjustment from 5 - 100 W.
• ECO Mode: Battery-saving mode that conserves battery life during use.

Additional Settings:

Press the [Power Button] 3 times quickly to enter the settings menu. Navigate using the [+/- Buttons] and confirm selections with the [Power Button]:

• THEME: Select the device's display theme.
• ANIMATION: Enable or disable puff animations on the display.
• LIGHT: Turn the side panel LED lighting on or off.
• PUFF CLEAR: Reset the puff counter.
• EXIT: Return to the main screen.

Vaping:

Press and hold the [Power Button] to take a puff. Release the button when finished.

Charging:

Connect the [USB-C Port] to a power source using a USB-C cable (not included). Recommended adapter specifications are 5V / 2A.

Software Upgrade:

Software upgrades can be downloaded from the official VooPoo website (www.voopoo.com). Use only the original USB-C cable from the package and ensure the device is fully charged for upgrades.

Battery Status Indicators:

• Charging: The display shows a battery icon and "Charging".
• Low Power (<10%): Red battery icon and "LOW POWER".
• Low Power (<20%): Yellow battery icon and "LOW POWER".

Error Codes and Indicators

• CHECK BATTERY: Check the power source and ensure the battery is inserted correctly.
• MAX POWER: Maximum adjustable wattage in SMART mode for the installed coil has been reached.
• CHECK ATOMIZER: Short circuit detected. Check the atomizer and coil for damage; replace the coil if necessary.
• TIME OUT: Maximum puff duration reached.
• ATOMIZER SHORT: Short circuit in the coil. Replace the coil.
• TEMP HIGH: Device temperature is too high. Allow it to cool down for a few minutes.

Warnings and Safety Precautions

• Age Restriction: This product is strictly prohibited for children and persons under 18 years of age. Not recommended for young people, non-smokers, pregnant or breastfeeding women, or individuals with heart conditions, hypertension, diabetes, depression, or asthma. Keep out of reach of children, non-smokers, and pets.
• Environment: Keep away from fire, water, and excessive heat. Store in a cool, shaded environment.
• Handling: Do not immerse the device in water, drop it, or throw it.
• Transport: Turn off or lock the device when carrying it if these functions are available.
• Usage: Use the device responsibly according to your personal situation. Stop use immediately if you experience discomfort.
• Recycling: Do not dispose of the device as regular waste. Recycle it at an electronic waste collection point. Recycle batteries separately at designated battery collection points.
• Charging: Use the original VooPoo charging cable. If the device is not used for an extended period, recharge it regularly to prevent battery discharge.
• Storage: Do not store the e-cigarette for longer than 3 months without recharging. Recommended storage temperature is -5°C to 30°C with 25% ± 75% RH humidity. Use the device within ambient temperatures of 0°C to 40°C.
• Servicing: Do not disassemble the device yourself. Contact your supplier for warranty claims or repairs.
• Charging Location: Charge the device indoors only. Use a quality UL-certified USB adapter to prevent fire or explosion hazards.

Atomizer Notes:

• E-liquid Leaks: When traveling by air, pressure changes may cause e-liquid leaks. Pack the atomizer separately and away from other items, or travel with an empty tank.
• Condensation: Condensation may form on the atomizer connection due to temperature changes. Wipe the atomizer with a dry paper tissue if this occurs.

General Operating Principles:

• Always use e-liquids with appropriate viscosity to prevent leaks or spitting.
• Never leave a charging e-cigarette unattended.
• Prevent drops and impacts to avoid battery damage.
• Keep the device away from water, flammable materials, and excessive heat.
• Do not expose the device to extreme temperatures.
• Recommended storage temperature: -5°C to 30°C. Recommended operating temperature: 0°C to 40°C.

Manufacturer Information

Manufacturer: VooPoo

Importer: 2Hservice s.r.o.

Address: Křivenická 444/33, Praha, Česká Republika

Website: www.mastervaper.cz

Phone: +420 734 645 645

CE and RoHS certifications are present.