Hooke Road Inter Cargo Rack Installation Instructions
Model: BXG.4600-S
Introduction
This document provides step-by-step instructions for installing the Hooke Road Inter Cargo Rack (Model BXG.4600-S). Please read all instructions carefully before beginning the installation process.
Attention: ? Please verify all parts are present and read instructions carefully before starting installation. Please feel free to contact your distributor if you have any kind of question about your purchase.
Contents
The following parts are included in the kit:
- Part A: Mounting Brackets (x2) - L-shaped metal brackets for attaching to the vehicle's roof.
- Part B: Reinforcement Bracket (x1) - A single, angled metal bracket for structural support.
- Part C: Reinforcement Plates (x2) - Flat metal plates with a grid pattern, used to connect rack sections.
- Part D1 & D2: Back Panels (x2) - Tall, rectangular metal panels with a grid pattern, designed to fit vertically at the rear of the rack.
- Part E1 & E2: Cargo Rack (x2) - The main cargo platform sections, featuring a grid pattern.
- Net: Cargo Net (x1) - A black elastic cargo net for securing items.
Parts List & Hardware
| Qty | Part Name | Size(mm) | Picture Description |
|---|---|---|---|
| 2 | Button Bolt | M8×25 | Bolt with a rounded head. |
| 12 | Button Bolt | M8×20 | Bolt with a rounded head. |
| 6 | Button Bolt | M8×16 | Bolt with a rounded head. |
| 4 | Button Bolt | M6×25 | Bolt with a rounded head. |
| 4 | Split Lock Washer | D6 | Washer with a split, designed to prevent loosening. |
| 14 | Split Lock Washer | D8 | Washer with a split, designed to prevent loosening. |
| 20 | Flat Washer | M8×16 | Flat circular washer. |
| 4 | Flat Washer | M6×16 | Flat circular washer. |
| 20 | Flange Lock Nut | M8 | Nut with an integrated flange to distribute pressure. |
Tools Required
- ? Drive Socket Ratchet Wrench
- ? 4mm, 5mm Hex Bit Socket
- ? 13mm Wrench
Installation Instructions
Step 1: Prepare the Vehicle
Place the vehicle in park, empty the rear row, and prepare to install the cargo rack.
Diagram Description: The interior rear section of an SUV is shown, with the headliner and grab handles visible. The vehicle is parked and ready for installation.
Step 2: Attach Mounting Brackets
Remove the handle and the plastic panel from the vehicle's headliner. Locate the factory installation holes. Repeat this step on the other side of the vehicle.
Secure the mounting bracket (A) to the vehicle using the provided hardware. Do not fully tighten the bolts at this stage to allow for adjustability. Repeat this step on the other side of the vehicle.
Hardware Used: (4) M6×25 Button Bolts, (4) D6 Split Lock Washers, (4) M6×16 Flat Washers.
Diagram Description: A close-up of the vehicle's headliner highlights factory-drilled holes after a handle and plastic panel have been removed. These are the mounting points. An illustration shows one mounting bracket (A) being attached to the vehicle's headliner using the specified hardware.
Step 3: Assemble Cargo Rack Sections and Panels
Assemble the cargo rack sections (E1&E2) with the back panels (D1&D2) and reinforcement plates (C). Tighten the hardware as specified.
Hardware for Reinforcement Plates (C): (4) M8×20 Button Bolts, (4) M8×16 Flat Washers, (4) D8 Split Lock Washers, (4) M8 Flange Lock Nuts.
Hardware for Back Panels (D1&D2): (4) M8×20 Button Bolts, (4) M8×16 Flat Washers, (4) D8 Split Lock Washers, (4) M8 Flange Lock Nuts.
Diagram Description: Shows two Reinforcement Plates (C) being attached to the Cargo Rack (E1&E2) using M8 hardware. Another diagram shows two Back Panels (D1&D2) being attached to the Cargo Rack (E1&E2) using M8 hardware. The step also involves attaching Reinforcement Brackets (B) using (2) M8×20 Button Bolts, (2) M8×16 Flat Washers, (2) D8 Split Lock Washers, and (2) M8 Flange Lock Nuts.
Step 4: Mount Cargo Rack Assembly
Secure the assembled cargo rack to the mounting brackets (A) already attached to the vehicle. Adjust the rack to the desired position. Finally, tighten all hardware securely. Repeat this step on the other side of the vehicle.
Hardware for attaching rack to brackets: (6) M8×16 Button Bolts, (6) M8×16 Flat Washers, (6) M8 Flange Lock Nuts.
Hardware for final vehicle attachment: (4) M8×20 Button Bolts, (4) D8 Split Lock Washers, (4) M8×16 Flat Washers, (4) M8 Flange Lock Nuts.
Diagram Description: The main cargo rack assembly is shown being secured to the mounting brackets (A) attached to the vehicle's headliner. The image depicts the use of M8 bolts, washers, and nuts for this final attachment.
Step 5: Installation Complete
The installation is complete. We hope you enjoy a wonderful off-road life with this quality Hooke Road product!
Diagram Description: The installed Hooke Road Inter Cargo Rack is shown mounted inside the rear of an SUV, holding cargo.
