Hulala Home NSHM1197D Nightstand
Item Number: NSHM1197D
Important Note
This brochure contains IMPORTANT safety info. Please read and keep for future reference.
Maintenance and Warning
- Keep furniture away from heat sources.
- Do not clean furniture with harsh cleaners or polishes. Do not use detergents, solvents, abrasives, spray packs, or leather cleaner. Use a non-colored mild soap with warm water to clean spills (Mix 1:10 soap to water).
- Do not place furniture under direct sunlight; material will possibly fade over time.
- Do not use an on-site dry cleaning machine. Children should not climb or jump on the furniture.
- Do not write on furniture that is not protected by a padded barrier.
- Not for commercial use, only for residential use.
Weight Limitation: 80 LBS ⚖️
Exploded View
The exploded view diagram shows all parts disassembled, illustrating how they fit together. Assembly requires 2 persons. ?
Parts List
| Part Label | Description | Quantity |
|---|---|---|
| A | Top Panel | x1 |
| B | Bottom Panel | x1 |
| C | Side Panel (Left) | x1 |
| D | Side Panel (Right) with drawer slides | x1 |
| E | Back Panel (Upper) | x1 |
| F | Back Panel (Lower) | x1 |
| G | Back Panel (Main) | x1 |
| H | Power/LED Module Housing | x1 |
| I | Glass Shelf | x1 |
| J | Top Drawer | x1 |
| K | Drawer Front | x1 |
| L | Drawer Side (Left) | x1 |
| M | Drawer Side (Right) | x1 |
| N | Drawer Bottom Support | x1 |
| O | Drawer Bottom Panel | x1 |
Hardware List
| # | Description | Quantity |
|---|---|---|
| #1 | Screw (Ø8#*1-1/4") | x15 |
| #2 | Screw (Ø3*14mm) | x14 |
| #3 | Anti-collapse Bracket | x4 |
| #4 | Screw (Ø3*16mm*6#) | x4 |
| #5 | Screw (Ø3*12mm) | x2 |
| #6 | Power/LED Module | x1 |
| #7 | Shelf Holder | x4 |
| #8 | Drawer Knob | x1 |
| #9 | Screw (Ø32/5"*1") | x1 |
| #10 | Screw (Ø3.5*35mm*7#) | x4 |
| #11 | Expandable Screw | x4 |
| #12 | Plastic Belt (Anti-collapse) | x2 |
Tool List
| # | Description | Quantity |
|---|---|---|
| #13 | Allen Wrench (M4) | x1 |
| #14 | Screwdriver | x1 |
Assembly Instructions
STEP-1
Connect part (F) to part (E) using screw #1 and screwdriver #14. The diagram illustrates this connection with three #1 screws.
STEP-2
Insert the combined (E/F) assembly into part (D). Ensure all holes align and tighten with allen wrench #13. The diagram depicts this attachment.
STEP-3
Attach part (C) to the (E/F/D) assembly. Align holes and tighten with allen wrench #13, as shown in the diagram.
STEP-4
Connect the unit pre-assembled in Step 3 to the base part (B). Align holes and tighten using allen wrench #13, as illustrated.
STEP-5
Attach the top panel (A) to the unit assembled in Step 4. Align holes and tighten with allen wrench #13, as shown.
STEP-6
Connect the main back panel (G) to the unit using 14 screws #2 and screwdriver #14. Ensure the USB plug passes through the designated cutout in panel (G), as shown in the diagram.
STEP-7
1. Attach part (H) to the unit with 4 screws #1 and screwdriver #14. 2. Secure two anti-collapse brackets (#3) to the top panel (A) using 4 screws #4 and screwdriver #14, as depicted.
STEP-8
Mount the Power/LED Module (#6) onto housing (H) using 2 screws #5 and screwdriver #14, as illustrated.
STEP-9
Insert four shelf holders (#7) into the pre-drilled holes on the inner sides of panels (C/D) at the desired level. Place the glass shelf (I) onto the holders. The diagram indicates shelf holders are adjustable.
STEP-10
Insert the top drawer (J) into its opening. Attention: Ensure the drawer slide rails are extended fully forward. The accompanying diagrams show the correct and incorrect alignment of drawer slide components.
STEP-11
1. Attach drawer sides (L/M) to the drawer bottom support (N) using 4 screws #1 and screwdriver #14. 2. Slide the drawer bottom panel (O) into the groove of (N) and between (L/M).
STEP-12
1. Attach drawer sides (L/M) to the drawer front (K) using 4 screws #1 and screwdriver #14. 2. Secure the drawer knob (#8) to the drawer front (K) using screw #9 and screwdriver #14.
STEP-13
Insert the assembled drawer into the main unit. Attention: Ensure the drawer slide rails are extended fully forward. The accompanying diagrams show the correct and incorrect alignment of drawer slide components.
STEP-14
Connect the USB light cable to the power outlet module. The light can be toggled on/off via its button, as shown in the diagrams.
STEP-15
Install the anti-collapse device: Mark wall position for bracket (#3) on panel (A). Drill and insert expandable screw (#11). Attach bracket (#3) to the wall using screw (#10) and screwdriver (#14), aligning with screw (#11). The diagrams illustrate these steps.
STEP-16
Thread the plastic belt (#12) through the anti-collapse brackets (#3) on both the wall and the furniture, then pull tightly to secure. The diagram shows this final safety step.
Warranty
- Hulala Home strives to offer high-quality products and does its best to satisfy each customer with product or service as needed.
- A 30-day warranty is provided starting from the time you receive the item. Each customer must provide a record of their order (order number or item receipt) for any items. Items out of the warranty period may still be considered.
- Replacement parts can be purchased from Hulala Home if they are available.
Support
Are you having difficulty with assembly? Missing parts? Please send an email with your order number to customerservice@hulalahome.com.
For returns, please check the return policy with the retailer or marketplace you purchased from.
Thank you for your purchase. Enjoy your new furniture piece!
