Important Note
This brochure contains IMPORTANT safety information. Please read and keep for future reference.
Document Date: 01/24
Maintenance and Warning
Follow these guidelines to maintain your furniture:
- Keep furniture away from heat sources.
- Do not clean furniture with harsh cleaners or polishes. Do not use detergents, solvents, abrasives, spray packs, or leather cleaner. Use a non-colored mild soap with warm water to clean spills (Mix 1:10 soap to water).
- Do not place furniture under direct sunlight; material will possibly fade over time.
- Do not use on-site dry cleaning machines. Children should not climb or jump on the furniture.
- Do not write on furniture that is not protected by a padded barrier.
- Not for commercial use, only for residential use.
Weight Limitation
⚖️ 110 LBS
Explosive View
An exploded view illustrating all components of the nightstand disassembled, ready for assembly. The assembly is estimated to take around 65 minutes and requires 2 persons ???.
Parts List
| Part | Description | Quantity |
|---|---|---|
| A | Top Panel | x1 |
| B | Bottom Panel | x1 |
| C | Side Panel (Left) | x1 |
| D | Back Panel (Upper with Legs) | x1 |
| E | Drawer Side (Left) | x1 |
| F | Drawer Side (Right) | x1 |
| G | Back Panel (Lower) | x1 |
| H | Drawer Front Support | x1 |
| I | Drawer Box Component | x3 |
| J | Drawer Slide Runner (Left) | x1 |
| K | Drawer Slide Runner (Right) | x1 |
| L | Drawer Side (Left) | x2 |
| M | Drawer Side (Right) | x2 |
| N | Drawer Slide Support/Rail | x3 |
| O | Drawer Back Panel | x1 |
| P | Drawer Front | x2 |
Note: There may be an inconsistency in the parts list regarding the quantity of Drawer Fronts (P). The product image shows 3 drawers, but only 2 'P' parts are listed.
Hardware List
| # | Description | Quantity |
|---|---|---|
| 1 | Bolt (1/4" x 1-1/4") | x4 |
| 2 | Flat Washer (1/4") | x4 |
| 3 | Screw (3*14mm) | x12 |
| 4 | Screw (8#*1") | x31 |
| 5 | Screw (5/32" * 1/2") | x12 |
| 6 | Power Outlet Unit | x1 |
| 7 | Anti-collapse Bracket | x4 |
| 8 | Screw (3*16mm*6#) | x4 |
| 9 | Screw (3.5*35mm*7#) | x4 |
| 10 | Expandable Screw | x4 |
| 11 | Plastic Belt | x2 |
Tool List
| # | Description | Quantity |
|---|---|---|
| 12 | Allen Key (M4) | x1 |
| 13 | Screwdriver | x1 |
Hardware Spare List
| # | Description | Quantity |
|---|---|---|
| 3 | Screw (3*14mm) | x1 |
| 4 | Screw (8#*1") | x1 |
Assembly Instructions
STEP-1
Insert part E into part F, make sure all holes align. Connect part E to part F with screw #4, tighten screw with screwdriver #13.
Diagram shows part E being inserted into part F. A close-up shows three screws (#4) being used with screwdriver #13 to secure them.
STEP-2
Insert panel (E&F) into panel D, make sure all holes aligned and then tighten it with allen key #12 as pictured.
Diagram shows the assembled E&F unit being attached to panel D. A close-up shows allen key #12 being used to tighten screws.
STEP-3
Insert panel B into panel D, make sure all holes aligned and then tighten it with allen key #12 as pictured.
Diagram shows panel B being attached to panel D. A close-up shows allen key #12 being used to tighten screws.
STEP-4
Insert side panel C into the corresponding hole of the pre-assembled unit from step 3. Make sure all holes align and use allen key #12 to tighten it as pictured.
Diagram shows side panel C being attached to the main structure. A close-up shows allen key #12 being used to tighten screws.
STEP-5
Connect part A to the unit pre-assembled at step 4 with bolt #1 and flat washer #2. Tighten bolt with allen key #12 as pictured.
Diagram shows the top panel A being attached to the main structure. A close-up shows bolt #1 and washer #2 being secured with allen key #12.
STEP-6
Insert back panel G into the groove of the pre-assembled unit from step 5. Make sure all holes aligned and use screw #3 to attach them. Tighten screw #3 with screwdriver #13.
Diagram shows back panel G being slid into grooves and secured with screws (#3) using screwdriver #13.
STEP-7
Connect part #7 (Anti-collapse Bracket) to parts C & D with screw #8. Tighten screw with screwdriver #13.
Diagram shows anti-collapse brackets (#7) being attached to the side and back panels (C&D) using screws (#8) and screwdriver #13.
STEP-8
Insert part H into the pre-assembled unit from step 7. Make sure all holes aligned and use screw #4 to attach them. Tighten screw #4 with screwdriver #13.
Diagram shows part H being attached to the unit. A close-up shows screws (#4) being used with screwdriver #13.
STEP-9
Insert part #6 (Power Outlet Unit) into the pre-assembled unit from step 8. Make sure all holes aligned and use screw #3 to attach them. Tighten screw #3 with screwdriver #13.
Diagram shows the power outlet unit (#6) being installed and secured with screws (#3) using screwdriver #13.
STEP-10
Connect parts J & K to part I using screw #4 and tighten it with screwdriver #13. Slide in part O into the groove in parts J&K. Make sure they are also in the groove in part I.
Diagram shows two stages: 1) Parts J and K being attached to part I with screws #4. 2) Part O being slid into the grooves of J&K, which are also in the groove of I. This step appears to be assembling a drawer box.
STEP-11
Connect parts J&K to part N using screw #4 and tighten it with screwdriver #13.
Diagram shows the assembled J&K&O unit being attached to part N using screws (#4) and screwdriver #13. This appears to be assembling the drawer slide mechanism.
STEP-12
Pull out the slide and attach the drawer (assembled in previous steps, referred to as I) to it. Make sure the slide is in the groove of part(J/K) and the end reaches the drawer front. Connect the drawer to the slide with screw #5 and tighten it with screwdriver #13.
Diagram shows a drawer box (labeled I) being attached to the drawer slides (part of J/K/N assembly). A close-up shows screws (#5) being used with screwdriver #13 to secure the drawer to the slide mechanism.
STEP-13
Connect parts L&M to part I using screw #4 and tighten it with screwdriver #13. Slide in part P into the groove in parts L&M. Make sure they are also in groove in part I.
Diagram shows two stages: 1) Parts L and M being attached to part I with screws #4. 2) Part P (drawer front) being slid into the grooves of L&M, which are also in the groove of I. This step assembles another drawer box.
STEP-14
Connect parts L&M to part N using screw #4 and tighten it with screwdriver #13.
Diagram shows the assembled L&M&P unit being attached to part N using screws (#4) and screwdriver #13. This appears to be assembling another drawer slide mechanism.
STEP-15
Pull out the slides and attach the drawers (assembled in previous steps, referred to as I) to them. Make sure the slide is in the groove of part(L/M) and the end reaches the drawer front. Connect the drawer to the slide with screw #5 and tighten it with screwdriver #13.
Diagram shows multiple drawers (labeled I) being attached to the drawer slides within the main unit. Close-ups show screws (#5) being used with screwdriver #13 to secure the drawers to the slide mechanisms.
STEP-16
Attention: Before the next step, adjust the feet of the locker to keep it level.
Diagram shows the bottom of the nightstand legs. Two close-ups illustrate adjusting the feet: one shows a warning symbol [warning] and an 'X' indicating incorrect adjustment, the other shows a checkmark [checkmark] and arrows indicating correct leveling adjustment.
STEP-17
Install the anti-collapse device.
- Mark the position on the wall that corresponds to the location of part #7 (Anti-collapse Bracket) on the furniture (parts C&D).
- Drill holes and insert the expandable screw #10 by hammer.
- Assemble the part #7 to the wall. Align the hole in the part #7 with the expandable screw #10. Use screw #9 to attach it and tighten by screwdriver #13.
Diagram shows the nightstand against a wall. Close-ups illustrate attaching brackets (#7) to the furniture and the wall using screws (#9, #10) and an expandable screw. The process is shown in three numbered steps.
STEP-18
Let the plastic belt #11 pass through both parts #7 (on furniture and wall) and pull tightly to secure the furniture to the wall.
Diagram shows the plastic belt (#11) being threaded through the anti-collapse brackets (#7) attached to both the furniture and the wall, and then pulled taut for safety.
Warranty
1. We strive to offer high-quality products, and we also try our best to satisfy each and every customer that orders from us with product or service as needed.
2. We provide a 30-day warranty starting from the time you receive the item. Each customer must provide a record of their order, such as the order number or item receipt. For items that are out of the warranty period, you may also still receive assistance.
3. Replacement parts can be purchased from our company if they are available.
For assembly assistance or missing parts, please send an email with your order number to: customerservice@hulalahome.com
For returns, please check the return policy with the retailer or marketplace where you purchased the item.
We appreciate your purchasing from us. Pop up your life by our furniture piece!
