Hulala Home SCYL0972 Cabinet

Maintenance and Warnings

1. Keep furniture away from heat sources.
2. Do not clean furniture with harsh cleaners or polishes. Do not use detergents, solvents, abrasives, spray packs, or leather cleaner. Use a non-colored mild soap with warm water to clean spills (Mix 1:10 soap to water).
3. Do not place furniture under direct sunlight, as the material may fade over time.
4. Do not use on-site dry cleaning machines. Children should not climb or jump on the furniture.
5. Do not write on furniture that is not protected by a padded barrier.
6. For residential use only; not for commercial use.

Explosive View

The following diagram shows an exploded view of the cabinet components, labeled A1 through A14.

Parts List

• A1 x1
• A2 x1
• A3 x1
• A4 x1
• A5 x1
• A6 x1
• A7 x2
• A8 x2
• A9 x4
• A10 x1
• A11 x2
• A12 x6
• A13 x1
• A14 x1

Hardware List

• B1 x16 (1/4"*5/8")
• B2 x8 (4MM*1-1/2")
• B3 x8 (Ø8*30MM)
• B4 x22 (Ø3*15MM)
• B5 x1
• B6 x16 (1/4"*12MM)
• B7 x16 (1/4"*16MM)
• B8 x32
• B9 x4
• B10 x4 (Ø4*20MM)
• B11 x4 (Ø4*39MM)
• B12 x4
• B13 x2

Tool List

• B14 x1 (1/4" Allen Key)
• B15 x1 (Screwdriver)

Assembly Instructions

Step 1

Insert side panels (A4 & A3) into panel (A1). Ensure all holes are aligned and then tighten with Allen key #14 as shown.

Step 2

Insert side panel (A5) into panel (A1). Ensure all holes are aligned and then tighten with Allen key #14 as shown.

Step 3

Prepare part A1. Align the holes in part A1, insert wooden dowel B3 by hand. Use screw B2 to attach the wine glass holder (A8 & A7) to the corresponding hole of panel (A1), and tighten the screw with screwdriver B15.

Step 4

Insert bottom panel (A2) into the corresponding hole of the preassembled unit from step 3. Ensure all holes are aligned and use Allen key #14 to tighten as shown.

Step 5

Open the back panel. Insert back panel (A6) into the groove of the preassembled unit from step 4. Ensure all holes are aligned and use screw B4 to attach them, tightening screw B4 with screwdriver B15.

Step 6

Insert gasket B6 and B7 in sequence into screw B1. Install leg A9 onto the bottom panel A2. Ensure the corresponding holes are aligned and fix with bolt #1, then tighten the screw with an Allen key #B14.

Step 7

Swivel mount the mid-foot A10 to the cabinet.

Step 8

Attention: Before the next step, adjust the feet of the cabinet to keep it level. [Adjust feet symbol]

Step 9

Install the door panel to the pre-assembled unit from step 8. [Move button symbol]

Sliding door wheel adjustment diagram: [Sliding door wheel adjustment diagram description]

Step 10

Attach the anti-collision pad B5 to the door panel.

Step 11

Insert shelf holder B8 into the corresponding hole of panel A4 & A5 and then attach panel (A11) to it. Shelf holder can be adjusted up or down.

Step 12

Insert shelf holder B8 into the corresponding hole of panel (A5 & A3) and then attach panel (A11) to it. Shelf holder can be adjusted up or down.

Step 13

Plan 1: Assemble the A12 components and place them into the cabinet.

Step 14

Plan 2:

1. Insert shelf holder B8 into the corresponding hole of panel (A5&A4) and then attach panel (A12) to it.
2. Insert shelf holder B8 into the corresponding hole of panel (A3&A5) and then attach panel (A12) to it.

Step 15

Use screw B11 to attach part B9 to the preassembled unit from step 14. Tighten screws with screwdriver B15.

Step 16

1. Install the anti-collapse device.
2. Mark the position on the wall that corresponds to the location of part B9 on panel (A1). Drill and insert the expandable screw B10 using a hammer.
3. Assemble part B9 to the wall. Align the hole in part B9 with the expandable screw B10, use screw B12 to attach it, and tighten with screwdriver B15.

Step 17

Let the plastic belt B13 pass through both parts B9 and pull tightly.

Warranty

1. Hulala Home strives to offer high-quality products and to satisfy every customer with product or service as needed.
2. A 30-day warranty is provided starting from the time the item is received. Each customer must provide a record of their order, such as the order number or item receipt, for any items outside the warranty period.
3. Replacement parts can be purchased from Hulala Home if they are available.

Are you having difficulty with assembly or missing parts? Please send an email with your order number to AMZCustomerservice@hulalahome.com.

For returns, please check the return policy with the retailer or marketplace where the product was purchased.

Thank you for your purchase. Enhance your life with our furniture piece!