Hulala Home NSCS1379D Nightstand Assembly and Maintenance Instructions
Product Overview
This document provides assembly instructions, maintenance guidelines, and warranty information for the Hulala Home NSCS1379D Nightstand.
⚠️ NOTE: This brochure contains IMPORTANT safety info. Please read and keep for future reference.
Item Number: NSCS1379D
Date: 01/22
Maintenance and Warning
- Keep furniture away from heat sources.
- Do not clean furniture with harsh cleaners or polishes. Do not use detergents, solvents, abrasives, spray packs, or leather cleaner. Use non-colored mild soap with warm water to clean spills (Mix 1:10 soap to water).
- Do not place furniture under direct sunlight, as the material will possibly fade over time.
- Do not use on-site dry cleaning machines. Children should not climb or jump on the furniture.
- Do not write on furniture that is not protected by a padded barrier.
- Not for commercial use, only for residential use.
⚖️ Weight Limitation: 100 LBS
Exploded View
The following diagram shows all parts of the nightstand disassembled. Assembly requires approximately 30 minutes and is recommended for two persons.
Parts Identification:
- A: Top Panel
- B: Bottom Panel
- C: Left Side Panel
- D: Right Side Panel
- E: Shelf Panel
- F: Drawer Front Support/Rail
- G: Drawer Back Support/Rail
- H: Drawer Side Panel
- I: Drawer Base Support/Mount
- J: Legs (x4)
- K: Back Panel
- L: Drawer Side Rail (Left)
- M: Drawer Side Rail (Right)
- N: Drawer Slide Mechanism (Left)
- O: Drawer Bottom Panel
- P: Drawer Front Panel
? Two Person Assembly Recommended
⏱️ Estimated Assembly Time: Around 30 min
Parts List
| Part Label | Description | Quantity |
|---|---|---|
| A | Top Panel | x1 |
| B | Bottom Panel | x1 |
| C | Left Side Panel | x1 |
| D | Right Side Panel | x1 |
| E | Shelf Panel | x1 |
| F | Drawer Front Support/Rail | x1 |
| G | Drawer Back Support/Rail | x1 |
| H | Drawer Side Panel | x1 |
| I | Drawer Base Support/Mount | x1 |
| J | Leg | x4 |
| K | Back Panel | x1 |
| L | Drawer Side Rail (Left) | x1 |
| M | Drawer Side Rail (Right) | x1 |
| N | Drawer Slide Mechanism (Left) | x1 |
| O | Drawer Bottom Panel | x1 |
| P | Drawer Front Panel | x1 |
Hardware List
The following hardware is included for assembly:
| # | Description | Quantity |
|---|---|---|
| #1 | Bolt (Ø5/32*30MM) | x1 |
| #2 | Screw (Ø3*15MM) | x2 |
| #3 | Handle Knob | x1 |
| #4 | Screw (Ø4*25MM) | x15 |
| #5 | Power Outlet/USB Module | x1 |
| #6 | Screw (Ø3*15MM) | x16 |
| #7 | Bolt (Ø1/4*40MM) | x4 |
| #8 | Wood Dowel (Ø8*30MM) | x10 |
| #9 | Bracket/Clip | x4 |
| #10 | Expandable Screw/Anchor | x2 |
| #11 | Mounting Bracket | x2 |
| #12 | Plastic Belt/Strap | x1 |
| #13 | Screw (Ø4*38MM) | x2 |
| #14 | Screw (Ø3*20MM) | x2 |
Tools Required:
| # | Description | Quantity |
|---|---|---|
| #15 | Allen Key (M4) | x1 |
| #16 | Screwdriver (Not included) | x1 |
Hardware Spare List:
| # | Description | Quantity |
|---|---|---|
| #7 | Bolt (Ø1/4*40MM) | x1 |
| #8 | Wood Dowel (Ø8*30MM) | x1 |
| #4 | Screw (Ø4*25MM) | x1 |
| #6 | Screw (Ø3*15MM) | x1 |
Assembly Instructions
STEP-1: Attach Legs
Install leg (J) onto the bottom panel (B). Ensure the corresponding holes are aligned. Fix with wood dowel #8 and bolt #7. Tighten the screw with Allen key #15.
Hardware Used: #8 (x8), #7 (x4), #15 (x1)
Diagram Description: Shows bottom panel B with four legs J being attached to its underside using bolts and dowels, with an Allen key #15 shown tightening a bolt.
STEP-2: Attach Drawer Supports to Side Panels
Insert panels (F & H) into side panels (C & D). Make sure all holes are aligned, then pull panels (F & H) forward and fix as shown in the picture.
Diagram Description: Shows side panels C and D with horizontal panels F and H being slotted into them. An inset shows a close-up of how the panels connect via slots.
STEP-3: Attach Drawer Shelf
Insert part (G) into parts (C & D & H). Make sure all holes are aligned. Fix with wood dowel #8 and screw #4. Tighten the screw with screwdriver #16.
Hardware Used: #8 (x2), #4 (x3), #16 (x1)
Diagram Description: Shows the partially assembled frame from Step 2, with shelf G being inserted. Screws #4 and dowels #8 are shown connecting G to C, D, and H. Screwdriver #16 is shown tightening a screw.
STEP-4: Attach Side Panels to Bottom Panel
Insert panels (C & D) into part (B). Make sure all holes are aligned, then pull panels (C & D) forward and fix as shown in the picture.
Diagram Description: Shows the bottom panel B with the assembled side structure from Step 3 being attached to it. An inset shows the connection detail.
STEP-5: Attach Drawer Base Support
Insert part (I) into the preassembled structure from Step 4. Ensure all holes are aligned and use screw #4 to attach them. Tighten screw #4 with screwdriver #16.
Hardware Used: #4 (x4), #16 (x1)
Diagram Description: Shows the main body of the nightstand. Part I is being attached to the inner structure, likely at the back or bottom of the drawer cavity, using screws #4.
STEP-6: Install Power Module
Insert part #5 (power outlet/USB module) into the preassembled structure (part I). Ensure all holes are aligned and use screw #2 to attach them. Tighten screw #2 with screwdriver #16.
Hardware Used: #5 (x1), #2 (x2), #16 (x1)
Diagram Description: Shows part I with the power module #5 being inserted and secured with screws #2. Screwdriver #16 is shown.
STEP-7: Attach Front Side Panel
Insert panels (C & D) into side panel (A). Make sure all holes are aligned, then pull panels (C & D) forward and fix as shown in the picture.
Diagram Description: Shows the main body of the nightstand being attached to the front panel A. This step seems to connect the main cabinet structure to the front face of the nightstand.
STEP-8: Attach Back Panel
Insert back panel (K) into the groove of the preassembled structure from Step 7. Make sure all holes are aligned and use screw #6 to attach them. Tighten screw #6 with screwdriver #16.
Hardware Used: #6 (x16), #16 (x1)
Diagram Description: Shows the nightstand from the back. The back panel K is being slid into grooves and secured with multiple screws #6. Screwdriver #16 is shown.
STEP-9: Adjust Legs
⚠️ Attention: Before the next step, adjust the feet of the locker to keep it level.
Diagram Description: Shows the assembled nightstand. Close-ups illustrate adjusting the feet of the nightstand to ensure it is level. An icon shows a screw being turned, and another shows a level surface with a checkmark. An 'X' icon indicates an incorrect method.
STEP-10: Insert Shelf Panel
Insert part (E) into part (C & D). Insert part #9 into the preassembled structure from Step 9. Make sure all holes are aligned and fix.
Hardware Used: #9 (x4)
Diagram Description: Shows the main cabinet. Shelf E is being inserted. Brackets #9 are shown being used to secure the shelf.
STEP-11: Assemble Drawer Sides and Bottom
1. Connect parts (M & N) to part (L) using screw #4 and tighten with screwdriver #16. 2. Slide in part (O) into the groove in parts (M & N). Make sure they are also in groove in part (L).
Hardware Used: #4 (x4), #16 (x1)
Diagram Description: Two stages are shown. Stage 1: Drawer side rails L and M are connected to drawer slide mechanism N using screws #4. Stage 2: Drawer bottom panel O is slid into the grooves of the assembled drawer sides.
STEP-12: Assemble Drawer Front and Attach Handle
1. Connect the drawer assembly (P and M&N) using screw #4, and tighten with screwdriver #16. 2. Install handle #3 to panel (P) using bolt #1 and tighten with screwdriver #16.
Hardware Used: #4 (x4), #16 (x1), #1 (x1), #3 (x1)
Diagram Description: Two stages are shown. Stage 1: Drawer front panel P is attached to the drawer side assembly (M&N) using screws #4. Stage 2: Handle #3 is attached to the drawer front panel P using bolt #1.
STEP-13: Install Drawer Slides
⚠️ Attention: When installing the drawer, slide the steel ball slide rail of the side panel to the most front as pictured.
Diagram Description: Shows the assembled nightstand with the drawer being inserted. Close-ups show the "Female slider" (on the cabinet) and "Male slider" (on the drawer). A schematic diagram illustrates the correct and incorrect methods for disassembling/aligning the slide rails, using checkmarks and crosses.
STEP-14: Attach Plastic Bracket to Panel
Use screw #14 to attach plastic bracket #11 to panel (A). Make sure all holes are aligned and tighten screw #14 with screwdriver #16.
Hardware Used: #11 (x1), #14 (x2), #16 (x1)
Diagram Description: Shows the inside of the nightstand cabinet. Plastic bracket #11 is being attached to panel A using screws #14. Screwdriver #16 is shown.
STEP-15: Wall Mounting - Part 1
1. Mark the position on the wall that corresponds to the location of bracket #11 on panel A. Drill and insert the expandable screw #10 by hammer. 2. Assemble the bracket #11 to the wall. Align the hole in the bracket #11 with the expandable screw #10, use screw #13 to attach it, tighten screw #13 with screwdriver #16.
Hardware Used: #11 (x1), #10 (x2), #13 (x2), #16 (x1)
Diagram Description: Shows a brick wall. A bracket #11 is shown being marked on the wall. An inset shows drilling and inserting an expandable screw #10. Another inset shows bracket #11 being attached to the wall using screw #13 and screwdriver #16. Text "NOT PROVIDED" indicates wall mounting hardware might not be included.
STEP-16: Wall Mounting - Part 2
3. Let the plastic belt #12 pass through bracket #11 and pull tightly.
Hardware Used: #12 (x1)
Diagram Description: Shows the nightstand near a wall with brackets #11 attached. Plastic belt #12 is being threaded through the brackets and pulled tight to secure the furniture to the wall.
Warranty Information
- Hulala Home strives to offer high-quality products and aims to satisfy each customer with product or service as needed.
- A 30-day warranty is provided starting from the time the item is received. Each customer must provide a record of their order (e.g., order number or item receipt) for any warranty claims. Items out of the warranty period may still be considered.
- Replacement parts can be purchased from Hulala Home if they are available.
For assembly assistance or missing parts, please email: customerservice@hulalahome.com with your order number.
For returns, please check the return policy with the retailer or marketplace where the item was purchased.
Thank you for your purchase. Enhance your life with our furniture!
