Fortin EVO-ALL Regular Installation Guide for Ford Mustang (2005-2009)

Vehicle Compatibility and Supported Functions

This guide is for the Fortin EVO-ALL interface module installation in the following vehicle:

• Vehicle: Ford Mustang
• Years: 2005-2009

The EVO-ALL module supports the following vehicle functions (if equipped):

• Immobilizer bypass
• Lock
• Unlock
• Arm
• Disarm
• Parking Light
• Horn
• Foot-Brake Status

Firmware Version: Minimum required is 71.[52]. To update firmware and options, use the separately sold FLASH LINK UPDATER or FLASH LINK MOBILE tool.

Mandatory Installation Requirements

Hood Pin Switch: The hood pin switch is a mandatory safety element and must be installed if the vehicle can be remote started with the hood open. This ensures the vehicle's safety system functions correctly.

Installer Qualification: This module must be installed by a qualified technician. Incorrect wiring connections can cause permanent damage to the vehicle.

Vehicle Connection Points

The following connection points are identified within the vehicle:

1. Ignition Harness: Connections for (+)ACCESSORY, (+)IGNITION, (+)12V, (+)STARTER.
2. Brake Switch: Connection for (+)FOOT BRAKE.
3. Parking Lights Harness: Connection for (-)PARKING LIGHTS.
4. Transponder Connector: Connections for TX and RX.
5. Driver's Kick Panel: Connection for (-)TRUNK RELEASE.
6. Passenger's Kick Panel: Connections for (-)LOCK and (-)UNLOCK.

Wiring Diagram Overview

The wiring diagram illustrates the connections between the EVO-ALL module and the vehicle's electrical system. Key connection points and wire functions are detailed:

EVO-ALL Module Connections:

• RS1: 12V BATTERY (+) (Red wire)
• RS2: Ground (-) (Black wire)
• RS3: PARKING LIGHTS (-) (Lt. Blue wire)
• RS5: IGNITION (+) (Purple wire)
• RS6: ACCESSORY (+) (Purple/White wire)
• RS7: STARTER (+) (Yellow wire)
• RS8: HOOD PIN CONTACT (-) (Green wire)
• RS9: HAND BRAKE (-) (Gray wire)
• RS10: TACHOMETER (+/-) (Orange wire)
• RS11: TRUNK RELEASE (-) (Orange/Black wire)
• RS12: DOOR (-) (Dk. Blue wire)
• RS13: FOOT BRAKE (+) (Red/Blue wire)
• RS14: GROUND OUT WHILE RUNNING (-) (Black wire)
• RS15: TRUNK (-) (Lt. Blue/Black wire)
• RS16: UNLOCK (-) (Pink wire)
• RS17: LOCK (-) (Yellow/Black wire)
• RS18: RX (Lt. Blue wire)
• A1: TX (Pink/Black wire)
• A2: (Purple/Yellow wire)
• A3: (Green/White wire)
• A4: (Green/Red wire)
• A5: (White/Black wire)
• A6: (Green wire)
• A7: (White wire)
• A8: (Orange wire)
• A9: (Orange/Black wire)
• A10: (Dk. Blue wire)
• A11: (Red/Blue wire)
• A12: (Black wire)
• A13: (Pink wire)
• A14: (Yellow/Black wire)
• A15: (Brown/White wire)
• A16: (Pink/Black wire)
• A17: (Purple/Yellow wire)
• A18: (Green/White wire)
• A19: (Green/Red wire)
• A20: (White/Black wire)

Vehicle Connection Locations:

• Passenger's Kick Panel: 26-Pin Black Connector (Pins 1-26).
• Driver's Kick Panel: 10-Pin Black Connector (Pins 1-10).
• Brake Switch: 2-Pin Gray Connector.
• Parking Lights Harness: 10-Pin Black Connector.
• Transponder Connector: 4-Pin Black Connector.
• Ignition Harness: 7-Pin Black Connector.

Data-Link Connection: Note whether the Data-Link connection is always required, not required with Data-Link, or direct connection.

Programming Procedures

2 Key Programming Procedure

This procedure requires two functional keys for the vehicle.

1. Step 1-3: Press and hold the programming button on the module. Connect the 4-Pin Data-Link harness (black connector). The Blue, Red, Yellow, and Blue & Red LEDs will illuminate alternately. Release the programming button when the RED LED is solid. If the RED LED is not solid, disconnect the Data-Link connector and return to Step 1.
2. Step 4: Insert the remaining required connectors.
3. Step 5: Turn the first key to the Ignition ON/RUN position. Wait 3 seconds.
4. Step 6: Turn the key to the OFF position and remove the first key.
5. Step 7: Turn the second key to the Ignition ON/RUN position. Wait 3 seconds.
6. Step 8: Turn the key to the OFF position and remove the second key.
7. Step 9 (Critical Timing): Within 5 seconds, press and hold the programming button until the RED LED flashes once (1x). Release the programming button.
8. Step 10 (Transmission Type):
   • Automatic Transmission: Activate the remote starter. The RED LED will flash rapidly ten (10) times.
   • Manual Transmission: Using a jumper wire, apply 12V power to the vehicle's ignition (Ignition1). The RED LED will flash rapidly ten (10) times. After programming, remove the jumper wire.
9. Step 11: If the RED LED is solid after the flashing sequence, disconnect the 4-Pin Data-Link connector and return to Step 1. Otherwise, the module is now programmed.

Testing: Use the remote starter or security system remote to test all supported features to ensure proper programming.

DCryptor Programming Procedure

This procedure requires specific software and hardware tools:

• Required Parts (not included): FLASH LINK UPDATER, FLASH LINK MOBILE, or FLASH LINK MANAGER.
• Software/Connection: A Microsoft Windows computer with internet connection, OR a Smartphone (Android/iOS) with internet connection (provider charges may apply) and the FLASH LINK MOBILE APP.

Before Programming: Set the unit options and save them.

1. Step 1-3: Press and hold the programming button. Insert the 4-Pin Data-Link connector. The Blue, Yellow, Red, and Blue & Red LEDs will illuminate alternately. Release the programming button when the RED LED is solid. If the RED LED is not solid, disconnect the 4-Pin Data-Link connector and return to Step 1.
2. Step 4: Insert the required remaining connectors.
3. Step 5: Press and release the programming button once (1x). The RED LED will flash once.
4. Step 6: Turn the key to the Ignition ON/RUN position. The RED LED will turn OFF, and the YELLOW LED will turn ON.
5. Step 7: Turn the key to the OFF position and remove the key from the ignition barrel. The YELLOW LED will turn OFF. The RED LED will turn ON.
6. Step 8: Turn the key to the Ignition ON/RUN position. The RED LED will turn OFF. The YELLOW LED will turn ON.
7. Step 9: Turn the key to the OFF position and remove the key from the ignition barrel. The YELLOW LED will turn OFF. The RED LED will turn ON.
8. Step 10: Turn the key to the Ignition ON/RUN position. The YELLOW LED will turn ON and OFF. The RED LED will turn OFF.
9. Step 11: Turn the key to the OFF position and remove the key from the ignition barrel. The RED and YELLOW LEDs will alternate.
10. Step 12: Disconnect all connectors except the Data-Link (4-pin) connector.
11. Step 13: Use the appropriate tool (FLASH LINK UPDATER or FLASH LINK MOBILE) to visit the DCryptor menu.
12. Step 14: After DCryptor programming is completed, return to the vehicle and reconnect the 4-Pin Data-Link connector, followed by all other remaining connectors.

Verification: Test the remote starter and alarm functionality to ensure proper operation.

Remote Starter Functionality

To start the vehicle remotely:

1. Ensure all doors are closed.
2. Activate the remote start function using the remote-starter remote or the OEM remote.
3. The vehicle will start.
4. To unlock the doors, use the remote-starter remote or the OEM remote.
5. Insert the key into the ignition and turn it to the ON/RUN position.
6. Press the brake pedal.
7. The vehicle is now ready to be put into gear and driven.

Notices and Warnings

Firmware and Guides: Updated firmware and installation guides are regularly posted on the Fortin website (www.fortinbypass.com). It is recommended to update the module to the latest firmware and download the latest installation guide before proceeding with installation.

Disclaimer: The information in this guide is provided "as is" without warranty. The installer is solely responsible for verifying all circuits before connection. Only a computer-safe logic probe or digital multimeter should be used. Fortin Electronic Systems assumes no liability for the accuracy or currency of the information, nor for any installation errors or damages resulting from the installation process. This module must be installed by a qualified technician. This guide is for informational purposes only and may change without notice.

Technical Support: For assistance, contact Fortin Tech Support at 514-255-HELP (4357) or 1-877-336-7797.

Website: Visit www.fortinbypass.com for web updates.

Copyright © 2006-2018, Fortin Auto Radio Inc. All rights reserved. Patents pending.