Fortin EVO-ALL Installation Guide: Standalone and THAR-NIS1 Harness

Compatibility

This installation guide is for the Fortin EVO-ALL interface module with the THAR-NIS1 harness. It is ONLY COMPATIBLE WITH AUTOMATIC TRANSMISSION VEHICLES.

Supported Vehicles:

Vehicle functions supported depend on the specific vehicle's equipment.

Firmware and Bypass Options

Firmware Version: 72.[43] (NISSAN/INFINITI MINIMUM)

To add the firmware version and specific options, use the FLASH LINK UPDATER or FLASH LINK MOBILE tool (sold separately).

Bypass Options:

• C1: OEM Remote status monitoring (Lock/Unlock).
• D6: Push-to-Start functionality.
• A11: Hood trigger (Output Status). Set to OFF/NON if the vehicle is not equipped with a functional hood pin.

Parts Required (Not Included)

• FLASH LINK UPDATER / FLASH LINK MANAGER
• Microsoft Windows Computer with Internet connection
• FLASH LINK MOBILE / FLASH LINK MOBILE APP
• Smartphone (Android or iOS) with Internet connection
• 1x 10Amp Fuse
• 2x 1 Amp Diode
• 1x THAR-NIS1 Harness
• RSPB (sold separately)

Mandatory Installation Requirements

⚠️ HOOD PIN MANDATORY: The hood pin switch must be installed. If the vehicle can be remote started with the hood open, set Function A11 to OFF.

The installation of safety elements is mandatory. The hood pin is an essential security element and must be installed.

This module must be installed by a qualified technician. Incorrect connections can cause permanent damage to the vehicle.

Standalone Configuration Options

Configure the bypass option based on your remote starter setup:

• OEM Remote Stand Alone:
• D1.10: By default, LOCK, LOCK, LOCK.
• D1.1: LOCK, UNLOCK, LOCK.
• OEM Remote Monitoring:
• C1: OEM Remote Monitoring.
• With RF KIT Antenna:
• H1 to H6: Supported RF Kits. Select the appropriate RF Kit.
• Vehicle Hybrid Only:
• D4: Hybrid mode.

Remote Starter Functionality

To remote start the vehicle:

1. Ensure all doors are closed.
2. Press the OEM remote's Lock button 3 times consecutively.

The vehicle will start. To stop the remote start, press the Lock button 3 times again.

Remote Starter Diagnostics (Module RED LED):

• x2 flash: Brake ON
• x3 flash: No tach signal
• x4 flash: Ignition detected before start
• x5 flash: Hood Open

⚠️ WARNING CARD: Cut and stick the warning card on a visible place. It states the vehicle can be started by pressing the OEM remote's Lock button 3 times or via smartphone. Activate the safety switch located under the dashboard before working on the vehicle.

Wiring Diagrams and Connections

This section details the physical connections required for installation.

Key Port Locations:

• Key Port: Located on the lower dash, left of the steering column.
• Push-to-Start Button: Located on the back of the button.
• Passenger Kick Panel: Located on the side panel near the passenger footwell.

General Wiring Overview (EVO-ALL Module Connectors):

The EVO-ALL module has multiple connectors (A, B, C, D) for various connections:

• Connector A (20-pin): Primarily for vehicle-specific connections like Lock/Unlock, Ignition, Parking Lights, Hood Pin, Door Pins, etc.
• Connector B (5-pin): For RF Kit or Data-Link connections, and 12V Battery/Ground.
• Connector C (5-pin): For CAN High/Low signals.
• Connector D (6-pin): For outputs like Brake, (+)12V, etc.

Specific Connections (Refer to Diagrams):

Automatic Transmission Wiring:

• Power: Connect (+)12V Battery (B4 Red) and Ground (B3 Black).
• Ignition: Connect to the vehicle's Ignition wire (e.g., Yellow wire in A1).
• Lock/Unlock: Connect to the vehicle's Lock (e.g., Purple wire in A2) and Unlock (e.g., Purple/White wire in A3) wires.
• Parking Lights: Connect to the vehicle's Parking Lights wire (e.g., Red wire in A15).
• Hood Pin: Connect to the vehicle's Hood Pin wire (e.g., Green wire in A19). This is mandatory.
• Push-to-Start (PTS): Connect to the vehicle's PTS signal (e.g., Lt. Blue wire in A19).
• Brake Signal: Connect to the vehicle's Brake signal (e.g., White wire in D5).
• CAN Bus: Connect CAN High (e.g., Pink wire in A20) and CAN Low (e.g., Blue wire in A18) to the vehicle's CAN bus.

T-Harness Connections:

• The THAR-NIS1 harness simplifies connections. Some provided white connectors may not be used.
• The EVO-ALL module replaces the factory OBDII connector.

Important Notes:

• Always verify connections using a multimeter.
• An incorrect connection may cause permanent damage to the module or vehicle.
• Refer to the detailed wiring diagrams on pages 4-6 for specific pin assignments and wire colors for your vehicle model.

Key Bypass Programming Procedure

Follow these steps to program the key bypass:

1. Step 1: Insert the key into the key port. Press and hold the programming button. Connect the 4-PIN Data-link harness (Black connector). Observe the Blue, Red, Yellow, and Blue & Red LEDs illuminating alternately.
2. Step 2: Release the programming button when the LED turns YELLOW.
3. Step 3: Insert the required remaining connectors.
4. Step 4: Press and release the programming button twice. Wait for the YELLOW LED to turn ON solid.
5. Step 5: Press and release the Push-to-Start (PTS) button once. The RED LED will turn ON. Wait for the BLUE LED to turn ON solid.
6. Step 6: Press and release the PTS button once to turn ON ignition. Wait for the BLUE LED to flash rapidly.
7. Step 7: Press and release the PTS button once to shut off the ignition.
8. Step 8: Press and release the PTS button twice to turn ON the ignition. The BLUE, YELLOW, and RED LEDs will rapidly alternate. The YELLOW LED flashing rapidly indicates the key bypass is programmed.
9. Step 9: Press and release the PTS button once to shut off the ignition.

The module is now programmed. Test all supported features using the remote starter or security system to ensure proper programming.

If the BLUE, YELLOW, and RED LEDs do not become solid, repeat the PTS button sequence (press twice to turn OFF, once to turn ON Accessory) until they are solid.

Remote Starter Operation Summary

To operate the remote starter:

1. Ensure all doors are closed.
2. Remote start the vehicle by pressing the Lock button 3 times on the OEM remote, remote-starter remote, or proximity remote.
3. Enter the vehicle with your intelligent key.
4. The vehicle is now ready to be put into gear and driven.

⚠️ Important: If the vehicle is not unlocked using one of the specified methods, the remote starter will shut down as soon as any door is opened.

Notices and Support

Updated firmware and installation guides are posted regularly on the Fortin website. It is recommended to update the module to the latest firmware and download the latest installation guide(s) prior to installation.

WARNING: The information provided is on an "as is" basis. The installer is solely responsible for verifying all circuits and connections. Fortin Electronic Systems assumes no liability for accuracy or installation results. This module must be installed by a qualified technician. This guide is for suggestion only and may change without notice. Visit www.fortinbypass.com for the latest version.

Tech Support:

Tel: 514-255-HELP (4357) | 1-877-336-7797

Website: www.fortinbypass.com