Fortin EVO-ALL Installation Guide

Addendum - Suggested Wiring Configuration

Vehicle Compatibility

This guide provides installation instructions for the Fortin EVO-ALL interface module for the following vehicles:

Chevrolet Cobalt: 2005-2010
Chevrolet HHR: 2006-2011

The module supports key vehicle functions, including immobilizer bypass, door lock/unlock, arm/disarm, trunk release, tachometer, door status, trunk status, hand-brake status, and foot-brake status.

Firmware and Tools

The current firmware version is 70.[18]. For firmware updates and additional options, use the separate FLASH LINK UPDATER or FLASH LINK MOBILE tool.

Programmable Bypass Options

The module offers programmable bypass options:

D2: Unlock before / Lock after (Disarms OEM alarm).
A7: Foot Brake (output status), specifically for vehicles with automatic transmission.

Mandatory Installation Component: Hood Pin

The hood pin switch is a mandatory safety element and must be installed. If the vehicle is capable of remote starting with the hood open, function A11 should be set to OFF.

Important Installation Warnings

Warning: This module must be installed by a qualified technician. Incorrect wiring connections can cause permanent damage to the vehicle. The information in this guide is for reference only and may change without notice.

Connection Points Overview

Key connection points for the module are located at:

Ignition Connector: V DATA, (+) IGNITION, (+) ACCESSORY
Transponder Connector: (+) 12V IMMO
BCM (Passenger side center console): (+) FOOT BRAKE, DATA KEY LESS

Wiring Diagram and Connections

The wiring diagram illustrates the connections between the EVO-ALL module and the vehicle's electrical system. Key connections include:

Inputs: Hood Status (A15), Hand Brake Status (A14), Trunk Release (A13), Tachometer (A12), Foot Brake (RS13), Ground While Running (A8), Trunk Status (A5), Door Status (A4), Unlock (A3), Lock (A2), 12V Battery (RS1), Ground (RS1).
Outputs: Remote Starter (RS11), Ignition (RS12), Accessory (RS5), Parking Lights (RS4).
Data-Link: Connections are differentiated for systems with or without Data-Link.
CAN Bus: Connections for CAN SW, CAN HIGH, CAN LOW (C5, C4, C3).
Immobilizer: (+) 12V Immo connections (D6, D5).

Specific vehicle connectors involved are the 72-pin white connector at the BCM (C2), the 41-pin red connector at the BCM (C3), the 6-pin green connector at the ignition harness, and the 5-pin white connector at the transponder. The OBDII connector is also utilized.

Note: Special connection procedures are required for vehicles equipped with the PK3 immobilizer system.

Programming Procedure

Follow these steps to program the Fortin EVO-ALL module:

Press and hold the programming button. Connect the 4-PIN Data-link harness (Black connector). Observe the LEDs; Blue, Red, Yellow, and Blue & Red LEDs will illuminate sequentially.
Release the programming button when the BLUE LED is solid. If the BLUE LED is not solid, disconnect the 4-pin connector and return to step 1.
Insert all other required connectors.
Turn the vehicle key to the Ignition ON/RUN position. The YELLOW LED will illuminate.
Start the vehicle and hold the CRANK position for 3 seconds. The YELLOW LED will turn OFF, and the RED LED will turn ON.
Release the key from the CRANK/START position to the ON/RUN position. The RED LED will turn OFF, and the BLUE LED will flash rapidly.
Turn the key to the OFF position. The LED will turn OFF. The module is now programmed.

Notices and Support Information

Updated Firmware and Installation Guides: Fortin regularly posts updated firmware and installation guides on their website. It is recommended to download the latest versions before installation.

General Warning: The information in this guide is provided "as is" without warranty. The installer is solely responsible for verifying all circuits before connection. Only a computer-safe logic probe or digital multimeter should be used. Fortin Electronic Systems assumes no liability for the accuracy or completeness of the information or for any installation errors. Installation must be performed by a qualified technician. This guide is for informational purposes only and may be updated without notice.

Technical Support:

Phone: 514-255-HELP (4357) or 1-877-336-7797
Website: www.fortinbypass.com

	Fortin EVO-ALL Installation and Programming Guide for Scion tC (2005-2010) Comprehensive guide for installing and programming the Fortin EVO-ALL interface module in a Scion tC (2005-2010). Features detailed wiring instructions, programming procedures, and important safety notices.
	Fortin EVO-ALL Remote Starter & Bypass Module Installation Guide for Honda Accord This guide provides detailed installation and programming instructions for the Fortin EVO-ALL module, designed for Honda Accord (2023-2025) models with Push-to-Start and Hybrid systems. It includes wiring diagrams, option configurations, and remote starter functionality, emphasizing installation by qualified technicians.
	Fortin EVO-ALL Installation Guide for Ford GT (2005-2008) Comprehensive installation and programming guide for the Fortin EVO-ALL interface module in a Ford GT vehicle (2005-2008 models). Covers wiring, key programming, key bypass, and remote start functionality.
	Fortin EVO-ALL Installation and Programming Guide for Toyota Land Cruiser Hybrid This guide provides detailed instructions for installing and programming the Fortin EVO-ALL remote starter and bypass module for Toyota Land Cruiser Hybrid (2024-2025) models. It includes wiring diagrams, step-by-step procedures, and functionality explanations.
	Fortin EVO-ALL Installation and Programming Guide for Ford Mustang (2005-2009) This guide provides detailed instructions for installing and programming the Fortin EVO-ALL interface module in a Ford Mustang model years 2005 through 2009. It covers wiring connections, key programming procedures, DCryptor setup, and remote starter functionality, along with important safety warnings and technical support information.
	Fortin EVO-ALL Installation Guide for Nissan Frontier Comprehensive installation guide for the Fortin EVO-ALL interface module in a Nissan Frontier (2005-2019), covering wiring, programming, and remote start functionality.
	Fortin EVO-ALL Stand Alone Installation Guide for Cadillac CT5 (2020-2023) Comprehensive installation guide for the Fortin EVO-ALL remote starter and bypass module for Cadillac CT5 vehicles (2020-2023) with Push-to-Start ignition. Includes wiring diagrams, programming procedures, and function descriptions.
	Fortin EVO-ALL Installation Guide: Standalone and THAR-NIS1 Harness for Infiniti Vehicles Comprehensive installation and programming guide for the Fortin EVO-ALL interface module with THAR-NIS1 harness, compatible with Infiniti FX35, FX37, and QX70 models featuring push-to-start and automatic transmissions. Includes wiring diagrams, configuration options, and step-by-step programming procedures.