Lumary SMART Wi-Fi 3-WAY LIGHT SWITCH START GUIDE

Introduction

Thank you for purchasing your Lumary smart home product. Ready to get started? Download the Lumary app to manage your switches (and all other Lumary devices) straight from your phone or tablet. Easily connect to your home Wi-Fi and control multiple devices with the touch of your fingertips.

Contents

• Download & Register
• Install
• Reset & Restart
• Connect (Easy Mode)
• Connect (AP Mode)
• FAQ, Troubleshooting, Notices

What's in the Box

The package includes:

• 2x Smart Wi-Fi Light Switch
• 2x Face Plate
• 10x Wire Nut
• 4x Screws
• Start Guide
• Voice Control Guide

Diagram Description: The diagram shows the Lumary Smart Wi-Fi Light Switch, a faceplate, and accessories including screws and wire nuts. It indicates quantities: 4 screws (labeled X4) and 10 wire nuts (labeled X10).

Get Ready

• Turn OFF power supply at the circuit breaker or fuse. Use a noncontact voltage tester to ensure that power is off. More than one disconnect switch may be needed to turn off power.
• Confirm that you are replacing a 3-Way switch (typically involves five wires in each switch, and two switches controlling one fixture).
• Make sure the existing switch box has a neutral wire.

IMPORTANT: Please consult a licensed electrician if you cannot locate a neutral wire or are unfamiliar with electrical installations.

1. Download the Lumary app

Description: This section shows two screenshots of mobile devices. The left shows the Lumary app search result on an app store (likely iOS App Store) with a "GET" button. The right shows the Lumary app page on Google Play Store with an "INSTALL" button. Below the screenshots are buttons for "Download on the App Store" and "GET IT ON Google Play".

2. Register a Lumary account

STEP 1: Enter your mobile phone number or email address.

STEP 2: Enter the verification code and create a password.

STEP 3: Log into the app.

Description: This section details the account registration process. It shows screenshots of the Lumary app interface for registration, including fields for country/region, mobile number/email, verification code, and password. It guides the user through entering their phone number or email, receiving and entering a verification code, creating a password, and finally logging in.

3. Install

STEP 1: Shut off power at the circuit breaker for the switch that you are replacing. More than one disconnection may be required to turn off power. Use a noncontact voltage tester to ensure that power is off.

Diagram Description: Shows a circuit breaker panel with two switches, one labeled "OFF" and the other "ON". Below are symbols indicating "OK" (circle with a plus) and "Not OK" (cross with a plus).

STEP 2: Make sure the existing switch box has a neutral wire*. Remove old switch by disconnecting all wires.

*Neutral wire is typically white.

Diagram Description: Shows a standard wall light switch with wires coming out, and the text "Disconnect all wires."

STEP 3: Wiring Instructions

1. Connect Switch 1 & Switch 2's neutral wire (white) & load's neutral wire to your home's neutral wire.
2. Connect Switch 1's live wire (black) with load's live wire.
3. Connect Switch 2's live wire (black) to your home's live wire.
4. Connect Switch 1 & Switch 2's SW1 wires (brown) together.
5. Connect Switch 1 & Switch 2's SW2 wires (blue) together.
6. Connect Switch 1 & Switch 2's ground wire (green) to your home's ground wire.
7. Check that all wire nuts are secured.
8. Mark all wires with included stickers for next reference.

Diagram Description: A detailed wiring diagram shows two Lumary switches (Switch 1 and Switch 2) connected to a load (light bulb symbol), a neutral wire, a live wire, and a ground wire. The diagram color-codes the wires: Green for Ground, Brown for Load wire SW1, Blue for Load wire SW2, White for Neutral wire, and Black for Live wire. It also shows the connections to the switches and the main house wiring. The ground connection is marked as optional but recommended if present.

STEP 4: Use screws to secure Switch(s) into your wall. Snap on the included faceplate.

Diagram Description: Shows the Lumary switch being mounted into a wall box with screws. A faceplate is then snapped onto the switch.

STEP 5: Restore power by reversing step 1.

STEP 6: Once power is connected, the white indicator light will blink to indicate that switch is ready to connect to Wi-Fi. Refer to page 8 for reset instructions.

CAUTION: RISK OF ELECTRIC SHOCK OR FIRE. Please follow all safety instructions on page five before installing, serving, or removing your switch.

4. Reset and restart

QUICK TIP: On the Switch Faceplate, the Reset button is the Power Reset button, and the Restart button is also known as the Wi-Fi Reset button.

Diagram Description: Shows the Lumary switch with "RESET" and "RESTART" buttons labeled at the bottom. Lines point to these buttons with descriptions.

Power Reset: Press to reset the circuit if the switch isn't working.

Wi-Fi Reset: Press and hold to put it in Wi-Fi pairing mode.

See next page for Wi-Fi Reset instructions.

How do I reset Switch and what does the blinking light mean?

Reset Switch by pressing and holding the Wi-Fi Reset (Restart) button for 3 seconds until the indicator begins to rapidly flash. The Wi-Fi Reset button is located on the bottom right side of the switch (not the switchplate) labeled "Restart".

• Reset one time (press and hold) to reach Easy Mode (Rapidly blinking white, 2x per second).
• Reset again (press and hold) to reach AP Mode (Slowly blinking white, every 3 seconds).

Indicator Light Status:

• Solid: Connected
• Fast Blink: Easy Mode
• Slow blink: AP Mode
• On: Switched On
• Off: Switch Off

5. Connect: Easy Mode

STEP 1: Open the Lumary app. In the top corner of the Devices screen, click (+). Choose "Smart Power".

STEP 2: Make sure Switch's light is rapidly flashing white. If not, reset to reach Easy Mode to connect (Page 9). Press "Next Step" in the app.

Description: Shows the Lumary app interface. The left screen shows the "Devices" screen with a "+" icon to add a device. The right screen shows a device being connected, with a progress indicator and text "Power on the device and confirm that the indicator light is blinking quickly".

STEP 3: Enter your Wi-Fi network and password.

Description: Shows a "Set up Wi-Fi for the device" screen where the user enters their Wi-Fi credentials. It notes that the app is supported only on 2.4GHz Wi-Fi channels.

STEP 4: The Lumary app will connect to your switch.

Description: Shows a "Connecting Now" screen with an 8% progress indicator and text "Make sure your phone and device are as close to your router as possible". It lists steps like "Searching for device", "Registering device to the cloud", "Initializing your device".

NOTE: Lumary can't connect to 5GHz networks.

6. Connect: AP Mode

STEP 1: Make sure Switch's light is slowly flashing white. If not, reset to reach AP mode (page 9).

STEP 2: Open the Lumary app. In the top corner of the Devices screen, click (+). Choose "Smart Power". Choose "AP Mode" in the top corner.

Description: Similar to Easy Mode setup, but guides the user to select "AP Mode".

STEP 3: Press "Next" and enter your Wi-Fi details.

STEP 4: Follow the instructions to choose the device from your Wi-Fi list.

Description: Shows a "Connect to device's hotspot" screen. It instructs to open WLAN settings, connect to a Wi-Fi network named "Lumary-XXXX", and then click "Connect Now".

STEP 5: The Lumary app will connect to your Switch.

NOTE: Lumary can't connect to 5GHz networks.

Frequently Asked Questions

1. Can I share with family and friends?

   Yes, you can share access to your Switch and any other Lumary device. In the Lumary app, press the "Profile" button and click on "Device Sharing" to give or revoke sharing permissions. In order to share, the other user should already have downloaded the Lumary app and registered an account.

2. Can I group multiple Lumary devices together?

   Yes, you can group multiple same-type devices by room, location, or however else you want. The same devices can be in multiple groups. For example, if you create a group for "Bedroom" and another group for "Entire House," your Bedroom lights can be included in both groups. From your main device list, click on one of the devices you want to group, press the [settings icon] button on the top right for advanced settings, and click "Create Group." You'll be able to name a new group and choose which devices you'd like to group together.

3. How many devices can I control?

   Lumary app can control an unlimited amount of devices in an unlimited amount of locations. Your router may have a limit of how many devices can be connected to one router.

4. My Lumary device has a funny name. How do I rename it?

   From your main device list, click on one of the devices you want to rename, press the [settings icon] button on the top right for advanced settings, and click "Modify Device Name" (or "Modify Group Name"). You'll then be able to choose a more familiar name.

5. What should I do if the device appears offline or is unreachable?

   Make sure your Wi-Fi router is online and in range, and check that you have the latest Lumary functionality by clicking "Check for firmware update" in your device settings. If power is connected but the switch is not responding, hold down the Restart button to cycle the fuse and give the switch a jump start.

6. What's the wireless range?

   The range of your home Wi-Fi is heavily dependent on your home router and the conditions of the room. Check with your router specifications for exact range data.

7. If my Wi-Fi/Internet goes down, will Lumary App still work?

   Lumary products need to be connected to Wi-Fi in order to use them remotely.

8. What does the white light mean?

   The white light indicates power. If the white light is on, the switch is receiving power; if it is off, it is not receiving power. The white light also indicates connection. If it is solid, the switch is connected; if it is flashing quickly, the switch is ready to connect using the Easy Mode (page 10); if it is flashing slowly, the switch is ready to connect using the AP Mode (page 12).

Troubleshooting

Can't connect to Wi-Fi?

Make sure you entered the correct Wi-Fi password during the Wi-Fi setup. Check whether there are any Internet connection problems. If the Wi-Fi signal is too weak, reset your Wi-Fi router and try again.

Reset the device

To reconnect to Wi-Fi, hold down the Reset button for 3 seconds.

• Reset 1 time (press and hold) to reach Easy Mode, indicated by rapidly blinking white light. Refer to page 10 to connect in Easy Mode.
• Reset 2 times (press and hold) to reach AP Mode, indicated by slowly blinking white light. Refer to page 12 to connect in AP Mode.

System Requirements

• Existing neutral wire
• Existing single pole, one-way (not multi-location) light switch with box more than 2 inches deep
• Mobile device running iOS® 9 or higher or Android™ 4.1x or higher
• Existing 2.4GHz Wi-Fi network (not compatible with 5GHz Wi-Fi networks)
• Lumary app

IMPORTANT: Please consult a licensed electrician if you cannot locate a neutral wire or are unfamiliar with electrical installations.

Technical Specifications

• Input: 100V-240v, 50/60Hz
• Wireless Frequency: 2.4GHz
• Wireless Standard: IEEE802.11 b/g/n
• Max Output: 800W INC, 400W CFL, 400W LED

FCC Notice

This device complies with Part 15 of the FCC Rules. Operation is subject to the two following conditions:

1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

Important Information

Before installing, read and follow all precautions, including the following:

CAUTION: RISK OF ELECTRIC SHOCK OR FIRE

TAP must be installed and used in accordance with the National Electric Code. Please consult a licensed electrician if you are uncomfortable or unfamiliar with electrical work.

Disconnect power before installing or modifying this product.

CAUTION: Suitable for indoor use only.

Support

If you encounter any issues, please contact Lumary support at cs@inlintek.com for help.

To explore Lumary's full selection of products, visit: www.lumary.tech

Made in China