Assembly Instructions
Step 1
Attach the bottom crossbars to the side frames. Use 4x part 107271 screws. Gently tap screws with a hammer ? if needed.
Step 2
Insert 4x part 112614 dowels into the side frames. Then, insert 4x part 100481 cam lock screws into the corresponding holes. Ensure correct parts are used as indicated by icons (dowel 112614, cam lock screw 100481).
Step 3
Insert 4x part 112614 dowels into the side frames. Then, insert 4x part 100481 cam lock screws into the corresponding holes. Ensure correct parts are used as indicated by icons (dowel 112614, cam lock screw 100481).
Step 4
Insert 8x part 114613 dowels into the side frames. Then, insert 8x part 100481 cam lock screws into the corresponding holes. Ensure correct parts are used as indicated by icons (dowel 114613, cam lock screw 100481).
Step 5
Insert 16x part 101350 dowels into the pre-drilled holes on the frames. Ensure correct dowel (101350) is used, not 101354.
Step 6
Attach brackets to the frame assembly using 4x part 100347 screws. Note the 'R' (right) and 'L' (left) indicators.
Step 7
Attach the vertical support pieces to the frame assembly. Arrows indicate insertion direction.
Step 8
Attach another vertical support piece. Secure it using 2x part 122332 cam locks. Insert the cam lock and rotate to tighten.
Step 9
Slide a side panel into place on the frame assembly. An arrow indicates the direction of insertion.
Step 10
Attach another side panel. Secure it using 2x part 122332 cam locks.
Step 11
Insert 2x part 101350 dowels into the side panels. Ensure correct dowel (101350) is used, not 101354.
Step 12
Slide a large panel (likely a back or main side panel) into place. An arrow indicates downward movement.
Step 13
Secure the panel using 2x part 122332 cam locks.
Step 14
Attach another large panel. Use 2x part 101350 dowels. Ensure correct dowel (101350) is used, not 101354.
Step 15
Secure the panel using 2x part 122332 cam locks.
Step 16
Place the top frame/surface onto the assembled structure. Arrows indicate downward placement.
Step 17
Secure the top using 2x part 122332 cam locks.
Step 18
Secure the main structure using 6x part 122332 cam locks. Insert cam locks and rotate to tighten.
Step 19
Attach a panel using 4x part 109510 screws.
Step 20
Attach a large panel. Use 4x part 101350 dowels. Ensure correct dowel (101350) is used, not 101354.
Step 21
Attach two side pieces to a panel.
Step 22
Attach bracket 100001 using 4x part 100136 screws. Also use 4x part 120189 screws.
Step 23
Insert 2x part 114613 dowels. Ensure correct dowel (114613) is used, not 100481.
Step 24
Insert 4x part 101350 dowels. Ensure correct dowel (101350) is used, not 101354.
Step 25
Secure using 2x part 122332 cam locks.
Step 26
Insert 7x part 101354 dowels. Ensure correct dowel (101354) is used, not 101350.
Step 27
Attach bracket 100001 using 6x part 104323 screws.
Step 28
Attach 2x part 10143360 brackets.
Step 29
Attach brackets using 2x part 152526 screws and 2x part 10065533 screws.
Step 30
Insert 6x part 100481 cam lock screws. Ensure correct screw (100481) is used, not 114613.
Step 31
Attach wall mounting brackets. Use 2x part 109049 screws and 2x part 100823 washers.
Step 32
Place the main body of the changing table/chest onto the base structure. An arrow indicates downward placement.
Step 33
Secure the main body using 6x part 122332 cam locks. Insert cam locks and rotate to tighten.
Step 34
Attach brackets to the side of the unit.
Step 35
Drill holes as indicated by the drill icon ड्रिल.
Step 36
Attach components using 2x part 100823 washers and 2x part 109048 screws.
Step 37
Attach the changing table top mechanism. Use 2x part 100001 brackets, 2x part 105042 screws, and 2x part 109937 components. Follow icons for correct assembly and disposal of packaging.
Step 38
Insert 4x part 123492 dowels into the drawer base.
Step 39
Insert 4x part 101345 dowels into the drawer side panels. Ensure correct dowel (101345) is used, not 101350.
Step 40
Attach cam locks using 4x part 110a630. Ensure correct cam lock (110a630) is used, not 110630 or 119030.
Step 41
Slide the back panel into place. An arrow indicates downward movement.
Step 42
Attach a panel.
Step 43
Secure using 4x part 145718 screws.
Step 44
Attach cam locks using 4x part 119030.
Step 45
Attach drawer slide rails using 6x part 100347 screws.
Step 46
Attach bracket 123833 using 1x part 105344 screw.
Step 47
Attach component using 1x part 105344 screw.
Step 48
Assemble the drawer. Attach the knob (117616) using 1x part 119976 screw and 1x part 100823 washer.
Step 49
Final check and warning icons. Ensure the furniture is stable and properly assembled.
