Vimar View Wireless Smart Home Connected Dial Thermostat

Operating Modes

The thermostat supports three operating modes:

• Stand Alone: Operates independently.
• Bluetooth®: Connects via Bluetooth for configuration and control using the View Wireless App.
• Zigbee: Integrates with a Zigbee Smart Home Hub for advanced control and automation.

Getting Started

Download the View Wireless App: Available on smartphone/tablet app stores for configuration.

Firmware Update: It is recommended to check for and perform firmware updates upon initial device power-up.

Required for Configuration:

• Stand Alone: View Wireless App.
• Bluetooth®: View Wireless App, smartphone/tablet with Bluetooth.
• Zigbee: View Wireless App, Smart Home Hub (e.g., Samsung SmartThings Hub), Amazon Alexa, Google Assistant, or Siri for voice control.

Create an installer account on MyVimar (on-line).

Stand Alone Configuration

1. Wire all thermostats.
2. Launch the View Wireless App and log in with your created credentials.
3. Create the system and environments.
4. Associate thermostats with environments: Select 'Add' (+), choose the environment, name it, activate Bluetooth on your device, approach the thermostat, and press for 5 seconds until the ring flashes blue.
5. Configure functions and parameters for each thermostat.
6. Set time schedules, operating mode setpoints, and current time in the 'Temperature control' menu.

Note: In case of power outage, the thermostat reverts to manual mode. Resetting the date/time is necessary to restore automatic mode.

Bluetooth® Configuration

1. Wire all devices (switches, relays, thermostats, gateway).
2. Launch the View Wireless App and log in.
3. Create the system and environments.
4. Associate all devices except the gateway (associate it last). Follow the same association steps as in Stand Alone mode.
5. Set functions, parameters, and any accessory devices (e.g., magnetic contact art. 03980).
6. Transfer device configuration to the gateway and connect it to the Wi-Fi network.
7. Transfer the system to the Administrator user.

Refer to the View Wireless App manual for full details.

Zigbee Configuration

1. Follow points 1 and 2 of Bluetooth configuration.
2. Associate the thermostat directly with a Zigbee hub (e.g., SmartThings Hub).
3. Download Zigbee software onto the thermostat using the View Wireless App. Press the button until 'bt' is displayed and the ring flashes blue.
4. After conversion or software update, the thermostat enters pairing mode for 5 minutes (ring flashes white). If not in pairing mode, cycle power.
5. Associate the thermostat following the Zigbee hub's procedure.
6. Associate the module following the Zigbee hub's procedure.
7. Set thermostat parameters. Press the relevant button for parameter editing within the first 10 minutes of power-up or after restarting.

Thermostat Controls and Display

• Dial: Adjusts setpoint. In Bluetooth mode, turning the dial can switch to manual operation.
• Buttons: Used for control and configuration.
  • Short press: Selects Celsius/Fahrenheit.
  • Long press (5s): Enters configuration phase (bt).
  • Prolonged press (30s): Resets the device (rst) within the first 5 minutes of power-up.
• Programmable function key: Controls display brightness, RGB LED, heating/air conditioning mode, and calls up scenarios.
• Display: Shows status indicators like 'bt' (Bluetooth configuration), 'off'/'on' (thermostat status), '°C'/'°F' (units), brightness levels (L-0 to L-3), operating modes (H for heating, C for air conditioning), and 'opn*' for open window detection.
• Lightable ring: Indicates power status and operating mode.

Ring Signalling

• Flashing blue: Thermostat in configuration mode.
• Lit amber: Thermostat in heating mode, relay active.
• Lit blue: Thermostat in air conditioning mode, relay active.
• Lit amber (not active): Thermostat in heating mode, relay not active.
• Lit blue (not active): Thermostat in air conditioning mode, relay not active.
• Flashing red: Thermostat lost hourly value, switched to manual mode. Returns to automatic when hourly value is received.

Thermostat Date/Time Setting

In Stand Alone mode, if the 'ON Mode' is set to 'Automatic', date and time can be set directly on the device after a power outage.

1. Press to enter 'Time entry' phase.
2. Use the dial to set the day of the week (1=Monday, 7=Sunday).
3. Press to confirm and set the hours (00-23).
4. Press to confirm and set the minutes (00-59).
5. Press to confirm. The thermostat returns to its previous status.

Note: If no selection is made within 2 minutes, the procedure times out. To change time without a blackout, press the button for 5 seconds and follow steps 1-7.

Resetting the Thermostat

Press the button for 30 seconds within the first 5 minutes of powering up. The ring flashes blue and emits 2 white flashes to confirm the reset.

Installation Rules

• Installation and configuration must be performed by qualified personnel according to local regulations.
• The C-NO relay contact must be protected against overloads with a device not exceeding 10 A.
• Do not connect SELV circuits to C-NO terminals.
• Install the device in a flush or surface mounting box at a height of 1.5 m, avoiding heat sources, drafts, or direct sunlight.

Characteristics

• Rated supply voltage: 100-240 V~, 50/60 Hz.
• Power consumption: 0.55 W.
• RF transmission power: < 100mW (20dBm).
• Frequency range: 2400-2483.5 MHz.
• Terminals: L, N for line/neutral; 2 terminals for external temperature probe (art. 02965.1, etc., max 10m cable); 2 C-NO relay terminals.
• Relay output: 5(2) A 240 V~ voltage-free contact.
• Setpoint range: 4°C - 40°C.
• Fan coil settings: 3-speed (V1, V2, V3, Auto) or proportional (33%, 66%, 100%, Auto).
• Association: Can be associated with thermostatic heads (art. 03989) or managed via actuators (art. 03985, 03986).
• Temperature measurement precision: ±0.5°C (between +15°C and +30°C).
• Operating modes: Automatic, Manual, Reduction, Economy, Protection, Off, Timed Manual (Bluetooth only).
• Temperature control algorithms: ON/OFF or PID (Bluetooth only).
• Buttons: 4 front buttons for control and configuration.
• RGB LED: For configuration status and output status signalling.
• Operating temperature: 0 °C to +40 °C.
• Protection degree: IP30.
• ErP classification: Class I (ON/OFF), Class IV (PID).
• Number of cycles: 3,000 manual, 100,000 automatic.
• Display update: Every 10 s.
• Room temperature display range: 0 °C to +40 °C.
• Hysteresis: Adjustable via App (0.1 °C to 1 °C).
• Clock error: ≤ 1 s per day.
• Configuration: Via View Wireless App (Stand Alone, Bluetooth). Controllable via View App, Amazon Alexa, Google, Siri, Homekit (Bluetooth).

Regulatory Compliance

The product complies with RED, RoHS, and ErP directives, and relevant EN standards. Full EU declaration of conformity is available on the Vimar website.

WEEE Information: Dispose of the product at the end of its life cycle at designated municipal collection centers for electrical and electronic waste.

Examples of Use

• Thermostat climate control zone management: Integrates with gateways for zone control.
• Window contact management: Uses magnetic contacts (art. 03980) and modules (art. 03983) for open window detection.
• Climate control with heads: Manages heating zones using thermostats and thermostatic heads (art. 03989) or relays.
• Circulation pump management: Controls circulation pumps for summer (air conditioning) and winter (heating) modes using thermostats, heads, and relays (art. 03981, 03983, 03985).
• Multi-zone climate control: Manages multiple independent climate control zones using thermostats and relays per valve.
• Fan coil management: Controls 3-speed or proportional fan coils using actuators (art. 03985, 03986).

Use

The front buttons, display, dial, and ring lighting allow setting and displaying all operating modes. The dial adjusts setpoints and can switch to manual operation in Bluetooth mode. The thermostat can manage thermostatic heads or fan coils via actuators.