Assembly Instruction
43516254 ALMA DESK
Care Instructions
Wipe clean with a soft damp cloth. Do not use abrasive materials and solvents. Check and tighten all parts regularly. Do not place hot items such as coffee cups directly on the surface. Keep away from water and direct sunlight. Store in a dry place. For domestic use only. For indoor use only. A mild odour may be present when first opening this carton. Simply allow to air outside and this will fade.
Warning
Do not stand or sit on this unit. Do not use this unit unless all bolts and screws are firmly secured. Do not knock or drag this unit. Use only on a flat surface. Load top evenly to prevent from tipping over. This package contains small parts and sharp points. Keep away from children and babies. Adult assembly required. Failure to follow these warnings could result in serious injury.
Maximum Safe Load: 30kgs for top, 3kgs for drawer.
Hardware List
| Identifier | Description | Quantity |
|---|---|---|
| A | 6x35mm | 14pcs |
| B | 14pcs | |
| C | 8x30mm | 16pcs |
| D | 4x35mm | 12pcs |
| E | 3x12mm | 24pcs |
| CL | 300mm | 2pcs |
| CR | 300mm | 2pcs |
| H | 7x40mm | 6pcs |
| I | 24pcs | |
| J | 24pcs | |
| K | 4mm | 1pc |
| L | 6x12mm | 6pcs |
| M | 6x30mm | 18pcs |
| N | 4pcs | |
| O | 3x16mm | 4pcs |
Tools Required (Not Provided)
Do not tighten the screws fully during assembly. Fully tighten screws after the final assembly steps.
Part List
| Part Number | Description | Quantity |
|---|---|---|
| 1 | 1 PC | |
| 2 | 1 PC | |
| 3 | 1 PC | |
| 4 | 1 PC | |
| 5 | 1 PC | |
| 6 | 1 PC | |
| 7 | 1 PC | |
| 8 | 2 PCS | |
| 9 | 1 PC | |
| 10 | 1 PC | |
| 11 | 1 PC | |
| 12 | 1 PC | |
| 13 | 2 PCS | |
| 14 | 2 PCS | |
| 15 | 2 PCS | |
| 16 | 2 PCS | |
| 17 | 1 PC | |
| 18 | 1 PC | |
| 19 | 1 PC |
Assembly Steps
Step 1:
Attach Part 3 to Part 2. Use 4x Screw A (6x35mm), 2x Screw E (3x12mm), 2x Connector CL, and 2x Connector CR. The diagram shows screws and connectors being inserted into pre-drilled holes.
Flip the assembly 180 degrees.
Attach Part 4 to the flipped assembly. Use 4x Screw E (3x12mm) and 2x Connector CL. The diagram shows screws and connectors being inserted.
Note: Diagrams show connections between CL and DL, and CR and DR, indicating how these connectors might be used in subsequent steps or with other parts not explicitly detailed in this step's text.
Step 2:
Attach Part 1 to the base structure. Use 2x Screw A (6x35mm). The diagram shows screws being inserted into Part 1 and the base.
Attach Part 6 to Part 1. Use 2x Screw D (4x35mm) and 2x Screw C (8x30mm). The diagram shows screws being inserted into Part 6 and Part 1.
Step 3:
Attach Part 3 and Part 4 to the main frame (Parts 1 and 2). Use 6x Screw B and 8x Screw C (8x30mm). The diagram shows screws being inserted into various connection points.
The diagram also shows parts labeled I, II, III which may refer to specific types of fasteners or connection methods not fully detailed here.
Step 4:
Attach Part 5 to the structure. Use 6x Screw C (8x30mm) and 6x Screw H (7x40mm). The diagram shows screws being inserted into Part 5 and the main frame.
Attach drawer runners (Parts 7 and G) to the side panels. Use 8x Screw I and 1x Screw K. The diagram shows runners being attached with screws.
Attach Part 12 to the underside of the desk. Use 8x Screw M (6x30mm). The diagram shows screws being inserted into Part 12 and the desk frame.
Step 5:
Attach Part 19 to the frame. Use 16x Screw I and 16x Screw J. The diagram shows screws being inserted into Part 19 and the frame.
Attach Part 10 to the frame. Use 6x Screw L (6x12mm) and 10x Screw M (6x30mm). The diagram shows screws being inserted into Part 10 and the frame.
The diagram shows attaching the top frame and side supports using screws and connectors.
Step 6:
Assemble the drawer. Attach Part 15 to Part 13 and Part 14. Use 4x Screw A (6x35mm) and 4x Screw B. The diagram shows the drawer sides and back being joined.
Attach Part 17 to the drawer base. Use 6x Screw E (3x12mm). The diagram shows the drawer base being attached.
Attach drawer runners (DL, DR) to the drawer sides. Use 1x Connector DL and 1x Connector DR. The diagram shows the runners being attached to the drawer sides.
Step 7:
Attach the assembled drawer to the desk frame. Insert Part 18 into the drawer runners on the desk. Use 4x Screw A (6x35mm) and 4x Screw B. The diagram shows the drawer being slid into place and secured.
Attach drawer runners (DL, DR) to the drawer sides. Use 6x Screw E (3x12mm), 1x Connector DL, and 1x Connector DR. The diagram shows the runners being attached to the drawer sides.
Step 8:
Attach the drawer front (Part 18) to the drawer box (Part 16). Use 4x Screw N and 4x Screw O (3x16mm). The diagram shows the drawer front being attached to the drawer box with screws.
