Assembly Instructions: Kmart Gaming Desk

Important Information & Warnings

Please read the instructions carefully. Be sure you have all parts before you start assembling. Place all gaming desk parts on a clean and flat surface, such as carpet or rug, to prevent from being scratched.

WARNING:

• ⚠️ This package contains small parts and sharp points. Keep away from children and babies until assembly is completed. Adult assembly required.
• ? Do not sit or stand on the desk.
• ? Avoid scratching the surface.
• ? Do not knock or drag the product. Failure to follow these warnings could result in serious injury.
• ? When cleaning the surface, use a damp cloth or dry clean cloth. Do not use detergent or chemical cleaners.
• ? Avoid contact with water and direct sunlight.
• Maximum safe load: 40 kg.
• A mild odour may be present when first opening this carton. Simply allow to air outside and this will dissipate.

Note: A DC5V 1A or lower current output USB wall adaptor is required.

Assembly Instructions

Step 1

Attach the main desk surface (D) to the leg frames (A, B) using screws. Ensure parts are correctly oriented as shown in the diagram.

Parts Used:

• 2 x Part A (Leg Frame)
• 2 x Part B (Leg Frame)
• 1 x Part D (Desk Surface)
• 8 x S2 (Screws, M8*16)
• 2 x S3 (Screws, M8*16)
• 1 x S1 (Tool, Allen Key)

[Diagram Description: Shows desk surface D with two leg frames A and B being attached from underneath using screws S2, S3, and tool S1. Part C is also shown but not yet attached.]

Step 2

Attach the support structures (G, F, E) to the underside of the desk surface (D) using screws. Connect the USB power hub (if applicable) and attach the pen holder (E).

Parts Used:

• 4 x Part G (Support)
• 2 x Part F (Support)
• 1 x Part E (Pen Holder)
• 26 x S4 (Screws, M4*14)
• 4 x S5 (Screws, M4*14)
• 1 x S1 (Tool, Allen Key)

[Diagram Description: Shows the desk surface from underneath. Support parts G, F, and E are being attached with screws S4 and S5. A USB connection point is indicated.]

⚠️ Please tighten screws.

Step 3

Attach the desk feet (J) to the bottom of the leg frames (A, B).

Parts Used:

• 2 x Part J (Desk Foot)

[Diagram Description: Shows the bottom of the leg frames where two desk feet J are attached.]

Step 4: RGB Lighting and Accessories

Connect the RGB lighting components (A, B, C) to the desk. Connect the USB power cable. Attach the holder (D) for phone/tablet and the pen holder (E).

Parts Used:

• 1 x Ax1 (RGB Strip)
• 1 x Bx1 (RGB Strip)
• 1 x Cx1 (RGB Strip)
• 7 x Dx7 (Connectors/Screws)
• 1 x Ex1 (Controller/Hub)
• 8 x Fx8 (Screws)
• 3 x Gx3 (Cable Clips)

RGB Lighting Control:

• Button C (Color Changing Key): Offers 6 optional colors. Can be set to static single color or flowing loop color.
• Button M (Mode Control Key):
  • Press M first time: Enter Mode 1 (RGB light up, press C for 6 colors or dazzling mode).
  • Press M second time: Enter Mode 2 (Special volume control mode, light controlled by voice/music).
  • Press M third time: Switch off.

Accessories:

• Holder D: For iPad/phone, boarder-brake.
• Holder E: Pen holder.

[Diagram Description: Shows the desk with RGB strips being attached to the edges. Connectors and a USB port are shown. Button C and Button M are illustrated with their functions described. Holders D and E are also shown.]

12 Month Warranty

Thank you for your purchase from Kmart.

Kmart Australia Ltd warrants your new product to be free from defects in materials and workmanship for the period stated above, from the date of purchase, provided that the product is used in accordance with accompanying recommendations or instructions where provided.

This warranty is in addition to your rights under the Australian Consumer Law.

Kmart will provide you with your choice of a refund, repair or exchange (where possible) for this product if it becomes defective within the warranty period. Kmart will bear the reasonable expense of claiming the warranty. This warranty will no longer apply where the defect is a result of alteration, accident, misuse, abuse or neglect.

Please retain your receipt as proof of purchase and contact our Customer Service Centre on 1800 124 125 (Australia) or 0800 945 995 (New Zealand) or alternatively, via Customer Help at kmart.com.au for any difficulties with your product. Warranty claims and claims for expense incurred in returning this product can be addressed to our Customer Service Centre at 690 Springvale Rd, Mulgrave Vic 3170.

Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure.

For New Zealand customers, this warranty is in addition to statutory rights observed under New Zealand legislation.