SAT Shower Enclosure Installation Guide
Models: SIKOTLDNEW120L, SIKOTLDNEW120P
This document provides mounting instructions in English, Czech (Instalační návod), Slovak (Inštalacný návod), German (Montageanleitung), and Russian (Инструкция по установке).
Important Notes & Cleaning
Before installation, ensure the mounting area is clean and level. Follow these cleaning guidelines:
- ✔️ Use cleaning products suitable for pH levels between 6.8 and 7.2.
- ❌ Avoid cleaning products with pH levels below 6.8 or above 7.2.
Parts List
| Part No. | Description | Quantity |
|---|---|---|
| 1 | Screw ST4X40 | x3 |
| 2 | Screw ST4X40 | x6 |
| 3 | Screw ST4X40 | x1 |
| 4 | Screw ST4X40 | x9 |
| 5 | Profile | x1 |
| 6 | Profile | x1 |
| 7-L | Roller Assembly (Left) | x1 |
| 7-R | Roller Assembly (Right) | x1 |
| 8 | Handle | x1 |
| 9 | Handle Screw | x1 |
| 10 | Handle Cover | x1 |
| 11 | Roller Wheel | x2 |
| 12 | Guide Wheel | x2 |
| 13 | Guide Wheel Bracket | x2 |
| 14 | Profile Connector | x1 |
| 15 | Screw ST4X40 | x2 |
| 16 | Profile | x1 |
| 17 | Seal | x2 |
| 18 | Bottom Seal | x1 |
| 19-L | Bottom Profile (Left) | x1 |
| 19-R | Bottom Profile (Right) | x1 |
| 20-L | Bottom Profile (Left) | x1 |
| 20-R | Bottom Profile (Right) | x1 |
| 21 | Profile | x1 |
| 22-L | Profile (Left) | x1 |
| 22-R | Profile (Right) | x1 |
| 23-L | Bottom Bracket (Left) | x1 |
| 23-R | Bottom Bracket (Right) | x1 |
| 24 | Bracket | x1 |
| 25 | Screw ST4X30 | x1 |
| 26 | Profile | x1 |
| 27 | Wall Profile | x2 |
| 28 | Screw | x1 |
| 29 | Screw | x2 |
| 30 | Screw | x1 |
Assembly Instructions
Step 1: Wall Preparation
Prepare the wall for installation. Drill holes using a ?️ drill. Ensure the drilling depth is 15mm. The required wall plug diameter is Ø3.2mm, and the hole diameter for the profile is Ø6mm. The installation width should be between 1170~1200mm. Maintain a gap of 8~12mm for the wall profile.
Icons used: ?️ (drill), ? (hammer), ? (screw), ? (level).
Step 2: Attaching Wall Profiles
Attach the wall profiles (part 27) to the prepared wall. Drill Ø6mm holes. These profiles allow for an adjustment range of 0~15mm. Ensure correct orientation: "vnitřní strana koutu" (inner side of enclosure) and "vnější strana" (outer side).
Icons used: ?️ (drill), ? (screw).
Step 3: Attaching Bottom Profiles
Attach the bottom profiles (parts 21, 22-L/R, 23-L/R) to the base of the shower area. Note: "Vnitřní strana koutu -Easy Clean" (Inner side of enclosure - Easy Clean).
Icons used: ➡️ (arrow indicating placement).
Step 4: Attaching Rollers and Guides
Install the roller assemblies (parts 11, 12, 13, 14, 15, 16) onto the glass panels and corresponding profiles. Use screws and a wrench as shown.
Icons used: ? (wrench), ? (screw).
Step 5: Installing the Main Glass Panel
Carefully insert the main glass panel into the top track. Follow the directional arrows for correct placement.
Icons used: ➡️ (arrows indicating movement).
Step 6: Securing the Bottom of the Glass Panel
Secure the bottom of the glass panel to the base. Two options are provided:
- Option A: For acrylic or marble resin trays. Use screws ST4X30 and part 23.
- Option B: For tiled floors. Use screws with Ø6mm diameter and part 24.
Icons used: ?️ (drill), ? (screw).
Step 7: Attaching the Door Handle
Attach the handle (part 8) to the glass door using the provided screws (part 9) and cover (part 10). Note: "Vnitřní strana koutu -Easy Clean" (Inner side of enclosure - Easy Clean).
Icons used: ? (screw).
Step 8: Attaching the Bottom Seal
Attach the bottom seal (part 18) to the bottom edge of the glass door. Follow the directional arrows for correct placement.
Icons used: ➡️ (arrow indicating placement).
Step 9: Installing the Door onto the Track
Carefully lower the assembled door onto the bottom track. Ensure it engages correctly with the bottom profiles.
Icons used: ⬆️ (up arrow), ⬇️ (down arrow).
Step 10: Adjusting the Door
Adjust the door alignment using the provided screws and a wrench. The adjustment range is 0~15mm.
Icons used: ? (wrench), ? (screw).
Step 11: Final Checks and Adjustments
Perform final checks to ensure all parts are secure and the door operates smoothly. Make any necessary final adjustments. Be cautious around "wood" areas, likely indicating surfaces to avoid drilling or for sealing purposes.
Icons used: ✔️ (checkmark), ❌ (cross), ⚠️ (warning triangle).
Step 12: Attaching Top Profiles/Guides
Attach the top guide pieces (part 5) and rollers (parts 12, 13) to the top track. Ensure a gap of 0.5~1mm is maintained.
Icons used: ? (screw), ➡️ (arrow).
Step 13: Applying Sealing Tape
Apply double-sided adhesive tape (part 5) to the designated profile. Peel off the protective backing before proceeding.
Text: "Peel off double-sided adhesive tape."
Icons used: ➡️ (arrow).
Step 14: Sealing the Enclosure
Apply silicone sealant around the base and edges of the enclosure for waterproofing. Apply sealant at a distance of approximately 100mm from the edge. Allow 24H for the sealant to cure completely before use.
Icons used: ? (sealant gun).
