SAT SIKO Shower Door Installation Guide

Introduction

This guide provides detailed instructions for the installation of SAT SIKO shower doors from the SIKOTEXP series. Please follow these steps carefully to ensure proper assembly and function. The guide covers models:

• SIKOTEXP80CRT
• SIKOTEXP90CRT
• SIKOTEXP100CRT
• SIKOTEXP80CT
• SIKOTEXP90CT
• SIKOTEXP100CT

Ensure you have all parts and tools before beginning.

Important Notes

Water pH Requirement: For optimal performance and longevity, ensure the water used in the installation area has a pH level between 6.8 and 7.2. Avoid water with pH levels below 6.8 or above 7.2. (? pH: 6.8~7.2, ? pH < 6.8; pH > 7.2)

Easy Clean Feature: The inner side of the glass is treated with an 'Easy Clean' coating to simplify maintenance.

Parts List

Required Tools

The following tools are recommended for installation:

• Drill with Ø6.0mm and Ø8mm drill bits
• Spirit Level
• Measuring Tape
• Screwdriver (Phillips/Pozidriv)
• Hammer
• Pliers
• Pencil
• Safety Glasses
• Possibly a rubber mallet

Assembly Instructions

1. Step 1: Prepare Wall Profiles. Attach the wall profiles (A) to the wall. Ensure they are level and plumb. The diagrams show attaching the profile to the wall, indicating a specific distance (150mm) from the top and bottom edges for drilling points.

   Diagram shows attaching profile A to the wall, with measurements for hole placement.

2. Step 2: Attach Profiles to Glass. Mount the fixed profile (D) and wall profile (A) to the glass panel (P). This involves sliding them into place and securing them. The diagram shows the profiles connecting to the edges of the glass panel.

   Diagram shows profiles D and A being attached to the glass panel P.

3. Step 3: Secure Wall Profiles. Drill holes in the wall at the marked positions (using Ø6 mm and Ø8 mm bits as indicated). Insert wall plugs (H) if necessary. Attach the wall profiles (A) securely to the wall using screws (F). The diagram shows drilling into the wall and screwing the profile. It also indicates angle measurements (e.g., 90 degrees) and a 12mm dimension for the wall profile attachment.

   Diagram shows drilling into the wall, inserting plugs, and screwing profile A. Also shows angle measurements (e.g., 90 degrees) and a 12mm dimension for the wall profile attachment.

4. Step 4: Attach Bottom Profile. Fix the bottom profile (B) to the shower tray or floor. The diagram shows the bottom profile being attached, with a 37mm and 22mm dimension indicated for placement relative to the wall.

   Diagram shows attaching bottom profile B to the shower tray/floor.

5. Step 5: Mount Glass Panel. Carefully lift and position the glass panel (P) with attached profiles (A, D) onto the bottom profile (B). Ensure it is seated correctly. The diagram shows the glass panel being lowered into place.

   Diagram shows the glass panel P being mounted onto the bottom profile B.

6. Step 6: Attach Top Profile. Secure the top profile (C) to the wall profile (A) and the glass panel (P). This typically involves sliding it into place and fastening it. The diagram shows the top profile being attached.

   Diagram shows attaching the top profile C.

7. Step 7: Install Bottom Seal. Attach the bottom seal (L) to the bottom edge of the glass door. The diagram shows the seal being fitted onto the glass.

   Diagram shows attaching the bottom seal L to the glass door.

8. Step 8: Adjust Door Position. Make fine adjustments to the door's position and alignment. The diagram shows a 0-20mm adjustment range for the door, indicating screws for fine-tuning the vertical position (A(H)).

   Diagram shows adjusting the door position with a 0-20mm range.

9. Step 9: Attach Rollers and Secure. Attach the top rollers (M) and bottom rollers (N) to the glass panel (P). Ensure they are properly seated and secured. The diagram shows attaching the rollers and then securing them with screws. A checkmark (✔️) indicates correct installation.

   Diagram shows attaching top rollers M and bottom rollers N, securing them with screws, and a checkmark for correct installation.

10. Step 10: Install Handle. Attach the handle (K) to the glass door using the handle screws (J). The diagram shows the handle being mounted on the door.

    Diagram shows attaching the handle K to the door using screws J.

11. Step 11: Attach Bottom Guide. Install the bottom guide (O) to the bottom profile (B) or the shower tray. This helps stabilize the door. The diagram shows the bottom guide being attached.

    Diagram shows attaching the bottom guide O.

12. Step 12: Final Checks and Sealing. Perform final checks on all fittings and seals. Ensure the door opens and closes smoothly. The diagram shows final adjustments and a 24-hour waiting period (⏳ 24H) before use, likely for sealant to cure.

    Diagram shows final adjustments and a 24-hour waiting period.

Model Width Specifications