Sealey Gear Oil Transfer Pump & Fixing Kit TP67 & TP67/X

Product Overview

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble-free performance.

IMPORTANT: Please read these instructions carefully. Note the safe operational requirements, warnings & cautions. Use the product correctly and with care for the purpose for which it is intended. Failure to do so may cause damage and/or personal injury and will invalidate the warranty. Keep these instructions safe for future use.

1. Safety

• WARNING! Ensure all health and safety, local authority, and general workshop practice regulations are strictly adhered to when using this equipment.
• Familiarise yourself with the application and limitations of this product, as well as the specific potential hazards peculiar to the area.
• Ensure safety eye protection and protective clothing are worn when using this product.
• Keep the work area clean, uncluttered and ensure there is adequate lighting.
• Dispose of waste liquids in accordance with local authority regulations.
• DO NOT use the pump to transfer solvents.
• DO NOT use the pump for any purpose other than for which it is designed.
• DO NOT place the oil drum on an uneven surface, or in contact with any heat source.
• DO NOT attempt to move the oil drum by pulling on the oil supply or the fluid transfer hose.
• Keep the pump clean and store in a safe dry location when not in use.

2. Introduction

TP67: Self-priming pump with polypropylene body. Suitable for pumping gear-oil or other products with a similar viscosity. Includes 1.5m of hose and universal adaptor.

Note: If the container you have will not accept direct mounting of Model No. TP67, order a Model No. TP67DT Trolley and a TP67/X Top Plate. The pump fixes to the top plate which in turn mounts onto the trolley and avoids the need to connect the pump directly to the container.

TP67/X: Fixing Kit for EP80 Gear Oil Drums for use with Model No. TP67 Gear Oil Transfer Pump.

3. Applications

Note: As a rule, if the chemical you want to pump is delivered in a plastic container, then you can use a plastic pump to transfer it. The TP67 and TP67/X cannot be used for the transfer of solvents. The unit will handle most disinfectants, detergents, pesticides, degreasers, mild acids, alkalis, oils, weed-killers, and chemical additives. If in doubt as to the suitability of use with a particular substance, contact your local Sealey supplier for advice.

4. Assembly

Figure 1: TP67 Gear Oil Pump Components

Diagram Description: The diagram shows the TP67 Gear Oil Pump with numbered parts.

Figure 2: TP67/X Adaptor Kit Components

Diagram Description: The diagram shows the TP67/X Adaptor Kit with numbered parts.

Parts List

5. Assembly Instructions

5.1. Preparations for Assembly

• Remove parts 3, 5, 6, 7, 8 from the main pump assembly (refer to Figure 1), and store them in a safe place for future use.
• Identify parts 1, 2, and 4, and keep them for the adaptor assembly.

5.2. Adaptor Assembly

• Assemble as shown (refer to Figure 2) incorporating parts 1 and 2 from the main pump assembly.
• Take part 4 (lock nut), invert it, and fit it to the end of the pump.

Environmental Protection

Recycle unwanted materials instead of disposing of them as waste. All tools, accessories, and packaging should be sorted, taken to a recycling centre, and disposed of in a manner compatible with the environment. When the product becomes completely unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids according to local regulations.

Notes and Warranty

Note: It is Sealey's policy to continually improve products and as such, they reserve the right to alter data, specifications, and component parts without prior notice.

Important: No liability is accepted for incorrect use of this product.

Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim.

Contact and Registration

Register your purchase here.

Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR

Phone: 01284 757500

Email: sales@sealey.co.uk

Website: www.sealey.co.uk