TÜV Rheinland Test Report - Products

Report Summary

Test Report Number: CN25LGVD 001

Client: IKEA of Sweden AB

Test Item: Self-ballasted LED lamps

Model/Type Number: LED2402C3NA

Order Content: TÜV Rheinland EMC service

Test Specification: FCC 47 CFR Part 15, Subpart B:2023 Class B, ICES-005:2018, ICES-003:2020

Date of Testing: 2025-03-27

Issue Date: 2025-05-20

Test Result: Pass

Remarks

1. All test equipment used was calibrated according to the test laboratory's calibration program and complies with relevant standards. Traceability is ensured by the management system. Detailed information on test conditions, equipment, and measurement uncertainty is available upon request.

2. This document is digitally signed. TÜV Rheinland has not verified legal or other requirements applicable to this document; this is the user's responsibility. Digital signature validity can be confirmed by a separate document upon request (environmental fee applies). Verification details are available at go.tuv.com/digital-signature.

3. Test clauses marked with * were subcontracted to qualified subcontractors. Deviations from specifications are listed in the respective test clause.

4. Conformity statements are based on the "Zero Guard Band Rule" and "Simple Acceptance" (ILAC G8:2019, IEC Guide 115:2021), unless otherwise specified. Measurement uncertainty is not accounted for in the report.

Revision History

General Product Information

Product Function and Intended Use

The EUT (equipment under test) is an ordinary self-ballasted LED lamp for lighting and similar use. Refer to the user's manual for further information.

Ratings and System Details

• Rated input: AC 120 V, 60 Hz, 42 mA
• Rated power: 3.7 W
• RF IC: SiMG301

Independent Operation Modes

The basic operation modes are "ON" and "OFF". The test modes were:

• Mode 1: Warm lighting with maximum output.
• Mode 2: Warm lighting with minimum output.
• Mode 3: White lighting with maximum output.
• Mode 4: White lighting with minimum output.

Highest Frequency Generated or Used

The highest frequency used in the EUT is 2480 MHz.

Test Set-up and Operation Modes

Principle of Configuration Selection

For emission testing, the EUT was configured to measure its highest possible emission level under conditions adapted from the instructions for use. Tests were performed on 2025-03-27 for both conducted and radiated emissions.

Equipment and Cable Arrangement

Conducted Emission Setup: The setup includes the EUT, Line Impedance Stabilization Network (LISN), EMI receiver, computer, transformer, and power supply. The EUT is placed on a wooden support, 0.8m from the AMN. Excess cable is folded to a length of 0.3-0.4m.

Radiated Emission Setup (30-1000 MHz): The setup involves the EUT on a turntable, an antenna, and an EMI receiver. The test distance is 3m. The antenna height is varied from 1m to 4m, and the turntable rotates 360°.

Radiated Emission Setup (1-18 GHz): The setup includes the EUT on a turntable, absorbers, and an antenna. The test distance is 3m. The antenna height is varied from 1m to 4m, and the turntable rotates 360°.

Test Software

The "Home" APP for iPhone was used during the tests.

Special Accessories and Auxiliary Equipment

Countermeasures to Achieve EMC Compliance

No special measures were employed to achieve the requirement.

Conformity Decision Rule

For all EMI tests, compliance is determined by comparing measurement results directly with limits, as measurement uncertainties are less than specified values (CISPR 16-4-2). Measurement uncertainty is not taken into account.

Test Results - Emission

Emission in the Frequency Range up to 30 MHz (Conducted Emission)

Test Procedure: FCC 47 CFR Part 15, Subpart B:2023, ICES-005:2018, ICES-003:2020, ANSI C63.4-2014 and CISPR 16-2-1

Frequency Range: 0.15 – 30 MHz

Limits: Quasi-peak: 0.15-0.5 MHz (66-56 dBμV), 0.5-5 MHz (56 dBμV), 5-30 MHz (60 dBμV). Average: 0.15-0.5 MHz (56-46 dBμV), 0.5-5 MHz (46 dBμV), 5-30 MHz (50 dBμV).

Test Site: Shielded room

Input Voltage: AC 120 V, 60 Hz

Ambient Conditions: Temperature: 22.6 °C; Relative humidity: 53.2 %

Expanded Uncertainty (k=2): 2.33 dB

The minimum margin to the limit is 3.18 dB. The measurement setup used standard equipment and procedures. Disturbance voltage was measured on the neutral and phase lines. The spectral diagrams show Quasi-Peak and Average values against limits.

Mode 1: Warm lighting (Max Output) - Conducted Emission Results

Figure 1: Spectral Diagrams, Conducted Emission, 150 kHz – 30 MHz, L&N, Mode 1

Final Quasi-peak measurement result:

Final Average measurement result:

Mode 2: Warm lighting (Min Output) - Conducted Emission Results

Figure 2: Spectral Diagrams, Conducted Emission, 150 kHz – 30 MHz, L&N, Mode 2

Final Quasi-peak measurement result:

Final Average measurement result:

Mode 3: White lighting (Max Output) - Conducted Emission Results

Figure 3: Spectral Diagrams, Conducted Emission, 150 kHz – 30 MHz, L&N, Mode 3

Final Quasi-peak measurement result:

Final Average measurement result:

Mode 4: White lighting (Min Output) - Conducted Emission Results

Figure 4: Spectral Diagrams, Conducted Emission, 150 kHz – 30 MHz, L&N, Mode 4

Final Quasi-peak measurement result:

Final Average measurement result:

Emission in the Frequency Range above 30 MHz (Radiated Emission)

Radiated Emission (30-1000 MHz)

Test Procedure: FCC 47 CFR Part 15, Subpart B:2023, ICES-005:2018, ICES-003:2020, ANSI C63.4-2014 and CISPR 16-2-3

Product Classification: Class B

Frequency Range: 30 – 1000 MHz

Limits (3m distance): 30–88 MHz (40 dBμV/m), 88–216 MHz (43.5 dBμV/m), 216–1000 MHz (46 dBμV/m).

Test Site: Semi-anechoic chamber

Test Distance: 3 m

Input Voltage: AC 120 V, 60 Hz

Ambient Conditions: Temperature: 22.5 °C; Relative humidity: 48.3 %

Expanded Uncertainty (k=2): 5.40 dB

The minimum margin to the limit is 7.22 dB. The test was performed with the antenna in horizontal and vertical polarizations, with the EUT on an 80 cm wooden support, rotated 360°, and antenna height varied from 1m to 4m.

Mode 1: Warm lighting (Max Output) - Radiated Emission (30-1000 MHz) Results

Figure 5: Spectral Diagrams, Radiated Emission, 30 MHz – 1000 MHz, Horizontal polarization, Mode 1

Figure 6: Spectral Diagrams, Radiated Emission, 30 MHz – 1000 MHz, Vertical polarization, Mode 1

Mode 2: Warm lighting (Min Output) - Radiated Emission (30-1000 MHz) Results

Figure 7: Spectral Diagrams, Radiated Emission, 30 MHz – 1000 MHz, Horizontal polarization, Mode 2

Figure 8: Spectral Diagrams, Radiated Emission, 30 MHz – 1000 MHz, Vertical polarization, Mode 2

Mode 3: White lighting (Max Output) - Radiated Emission (30-1000 MHz) Results

Figure 9: Spectral Diagrams, Radiated Emission, 30 MHz – 1000 MHz, Horizontal polarization, Mode 3

Figure 10: Spectral Diagrams, Radiated Emission, 30 MHz – 1000 MHz, Vertical polarization, Mode 3

Mode 4: White lighting (Min Output) - Radiated Emission (30-1000 MHz) Results

Figure 11: Spectral Diagrams, Radiated Emission, 30 MHz – 1000 MHz, Horizontal polarization, Mode 4

Figure 12: Spectral Diagrams, Radiated Emission, 30 MHz – 1000 MHz, Vertical polarization, Mode 4

Radiated Emission (1-18 GHz)

Test Procedure: FCC 47 CFR Part 15, Subpart B:2023, ICES-005:2018, ICES-003:2020, ANSI C63.4-2014 and CISPR 16-2-3

Product Classification: Class B

Limits (3m distance): Peak: 1–18 GHz (74 dBμV/m); Average: 1–18 GHz (54 dBμV/m).

Test Site: Absorber-lined semi-anechoic chamber

Test Distance: 3 m

Test Voltage: AC 120 V, 60 Hz

Ambient Conditions: Temperature: 23.2 °C; Relative humidity: 52.8 %

Expanded Uncertainty (k=2): 5.17 dB (1-6 GHz), 5.12 dB (6-18 GHz)

The minimum margin to the limit is 10.32 dB. The test was performed with the antenna in horizontal and vertical polarizations, with the EUT on an 80 cm supporting table, rotated 360°, and antenna height varied from 1m to 4m.

Mode 1: Warm lighting (Max Output) - Radiated Emission (1-18 GHz) Results

Figure 13: Spectral Diagrams, Radiated Emission, 1 GHz – 18 GHz, Horizontal polarization on mode 1

Final peak measurement result:

Final average measurement result:

Figure 14: Spectral Diagrams, Radiated Emission, 1 GHz – 18 GHz, Vertical polarization on mode 1

Mode 2: Warm lighting (Min Output) - Radiated Emission (1-18 GHz) Results

Figure 15: Spectral Diagrams, Radiated Emission, 1 GHz – 18 GHz, Horizontal polarization on mode 2

Final average measurement result:

Figure 16: Spectral Diagrams, Radiated Emission, 1 GHz – 18 GHz, Vertical polarization on mode 2

Final average measurement result:

Mode 3: White lighting (Max Output) - Radiated Emission (1-18 GHz) Results

Figure 17: Spectral Diagrams, Radiated Emission, 1 GHz – 18 GHz, Horizontal polarization on mode 3

Final average measurement result:

Figure 18: Spectral Diagrams, Radiated Emission, 1 GHz – 18 GHz, Vertical polarization on mode 3

Final average measurement result:

Mode 4: White lighting (Min Output) - Radiated Emission (1-18 GHz) Results

Figure 19: Spectral Diagrams, Radiated Emission, 1 GHz – 18 GHz, Horizontal polarization on mode 4

Final average measurement result:

Figure 20: Spectral Diagrams, Radiated Emission, 1 GHz – 18 GHz, Vertical polarization on mode 4

Final average measurement result:

Test and Measurement Instruments

List of Test and Measurement Instruments

Photographs of the Test Set-Up

Refer to the test setup file.

List of Figures

• Figure 1: Spectral Diagrams, Conducted Emission, 150 kHz – 30 MHz, L&N, Mode 1
• Figure 2: Spectral Diagrams, Conducted Emission, 150 kHz – 30 MHz, L&N, Mode 2
• Figure 3: Spectral Diagrams, Conducted Emission, 150 kHz – 30 MHz, L&N, Mode 3
• Figure 4: Spectral Diagrams, Conducted Emission, 150 kHz – 30 MHz, L&N, Mode 4
• Figure 5: Spectral Diagrams, Radiated Emission, 30 MHz – 1000 MHz, Horizontal polarization, Mode 1
• Figure 6: Spectral Diagrams, Radiated Emission, 30 MHz – 1000 MHz, Vertical polarization, Mode 1
• Figure 7: Spectral Diagrams, Radiated Emission, 30 MHz – 1000 MHz, Horizontal polarization, Mode 2
• Figure 8: Spectral Diagrams, Radiated Emission, 30 MHz – 1000 MHz, Vertical polarization, Mode 2
• Figure 9: Spectral Diagrams, Radiated Emission, 30 MHz – 1000 MHz, Horizontal polarization, Mode 3
• Figure 10: Spectral Diagrams, Radiated Emission, 30 MHz – 1000 MHz, Vertical polarization, Mode 3
• Figure 11: Spectral Diagrams, Radiated Emission, 30 MHz – 1000 MHz, Horizontal polarization, Mode 4
• Figure 12: Spectral Diagrams, Radiated Emission, 30 MHz – 1000 MHz, Vertical polarization, Mode 4
• Figure 13: Spectral Diagrams, Radiated Emission, 1 GHz – 18 GHz, Horizontal polarization on mode 1
• Figure 14: Spectral Diagrams, Radiated Emission, 1 GHz – 18 GHz, Vertical polarization on mode 1
• Figure 15: Spectral Diagrams, Radiated Emission, 1 GHz – 18 GHz, Horizontal polarization on mode 2
• Figure 16: Spectral Diagrams, Radiated Emission, 1 GHz – 18 GHz, Vertical polarization on mode 2
• Figure 17: Spectral Diagrams, Radiated Emission, 1 GHz – 18 GHz, Horizontal polarization on mode 3
• Figure 18: Spectral Diagrams, Radiated Emission, 1 GHz – 18 GHz, Vertical polarization on mode 3
• Figure 19: Spectral Diagrams, Radiated Emission, 1 GHz – 18 GHz, Horizontal polarization on mode 4
• Figure 20: Spectral Diagrams, Radiated Emission, 1 GHz – 18 GHz, Vertical polarization on mode 4

End of test report